强化除磷型A/O-MBR工艺运行稳定性

采用缺氧/好氧膜生物反应器(A/O-MBR)处理合成的生活污水,考察了投加不同浓度的聚合氯化铝(PAC)对该工艺在除磷效能及运行稳定性方面的影响。结果表明,投加PAC可以有效降低出水TP的浓度;在投加量为150 mg/L时,TP的去除率达到最优,为90.1%,出水浓度维持0.48 mg/L左右,达到《城镇污水处理厂污染物排放标准》(GB18918-2002)的一级A标准。投加一定量的PAC可以有效提高微生物的活性;此外,可以降低污泥絮体的Zeta电位,增大污泥絮体的粒径,降低胞外聚合物(EPS)中多糖的浓度,进而有效延缓膜污染的速率。     

Congener-specific accumulation and environmental risk assessment of polybrominated diphenyl ethers in diverse Korean sewage sludge types

Industrial, domestic wastewater, and livestock sludge samples were collected from 23 wastewater treatment plants in Korea and analyzed for polybrominated diphenyl ethers (PBDEs). The concentrations of Σ₁₉PBDE ranged from 4.01 to 10,400 ng/g dry weight. The average Σ₁₉PBDE concentrations in industrial, domestic wastewater, and livestock sludge were 1,560?±?3,610, 402?±?148, and 27.6?±?50.4 ng/g dry weight, respectively. The composition of PBDEs differed according to the type of sludge. Among the PBDE congeners, BDE 209 was dominant in all sludge samples. After BDE 209, relatively high levels were found for BDE 28 and 47 from industrial sludge, BDE 47 and 99 from domestic wastewater sludge, and BDE 206, 207, and 208 from livestock sludge. Using hierarchical cluster analysis, sludges were divided into three groups according to PBDE congener composition. A risk assessment of PBDEs in sludge used for soil amendment was carried out. Preliminary results indicated that the potential risk of soil exposed to PBDEs in sludge was relatively low.     

A Survey of Nitrogen Dioxide Levels Measured Inside Mobile Homes

As part of the California Mobile Home Study, over 250 mobile homes from throughout the state were monitored for nitrogen dioxide (NO₂) concentrations. Week-long average measurements were taken with Palmes tubes in the kitchen and bedroom of each mobile home during the summer of 1984 and the winter of 1985. The study was conducted entirely by mail with the participants providing all the necessary information. Mobile homes using gas for cooking had significantly higher indoor NO₂ levels than those using electricity. Mobile homes located in the Los Angeles basin had significantly higher indoor NO₂ concentrations than did mobile homes in the rest of the state. Gas cooking, the inverse of the house volume and geographic location (as a surrogate of outdoor NO₂) were the most important variables identified by multiple linear regression.     

An Analysis of Biomedical Waste Incineration

The California Air Resources Board (ARB) completed a series of source tests of eight operating biomedical waste incinerators (BMWI) under conditions of typical operation. The emissions of certain metals, and chlorinated dioxins and furans in the flue gases of BMWI are relatively high in comparison to emissions from other combustion sources, such as hazardous waste or municipal waste incinerators of modern design. This study reports on an analysis of the status of the existing regulatory framework and the California data base. Clarification of definitional issues at the federal level is needed to effectively treat BMWI management issues. Although few relationships among combustion parameters and emissions were uncovered, patterns of emissions were evident, suggesting commonality and relationships among the waste stream constituents and emissions. Potential implications for future research, operation of BMWI, controls and source reduction and waste segregation strategies are also discussed.     

The Nonlinearity and Related Band Strength of Carbon Monoxide When Applied in Ambient Air Measurement Using Open Long-Path Fourier Transform Infrared Spectrometry

ABSTRACT

The accuracy of CO concentration determination by open-path Fourier transform infrared (FTIR) spectrometry has been re-evaluated in detail. The evaluation focuses on the correction of the calibration curve—the integrated intensity of a standard spectrum—that is used as a comparison spectrum when doing quantitative analysis of CO. Results show that the calibration curve (with 0.5 cm^-1 or 1 cm^-1 resolution) is apparently inclined to be nonlinear under standard conditions, and that the threshold point of nonlinearity is ~0.1 atm-cm. Two commercial FTIR field monitoring systems have been used to investigate the nonlinearity trend. The experimental method consists of using open-path FTIR systems in combination with nondispersive infrared (NDIR) monitors to establish the calibration curve in a semi-closed corridor. The results have been double-checked using closed-cell dynamic equilibrium systems.

When the optical density is larger than a certain value, the curves begin to bend, and when the optical density approaches zero, the band strength is around 178 ± 3 atm^-1 cm^-2 and 173 ± 2 atm^-1 cm^-2, respectively, for 0.5 and 1 cm^-1 resolution at standard temperature and pressure (STP). These values are quite different from other published data that have been acquired by the pressurized method or by high-resolution     

Laboratory and Field Evaluation of Measurement Methods for One-Hour Exposures to O3, PM25, and CO

ABSTRACT

While researchers have linked acute (less than 12-hr) ambient O₃, PM₂₅, and CO concentrations to a variety of adverse health effects, few studies have characterized short-term exposures to these air pollutants, in part due to the lack of sensitive, accurate, and precise sampling technologies. In this paper, we present results from the laboratory and field evaluation of several new (or modified) samplers used in the “roll-around” system (RAS), which was developed to measure 1-hr O₃, PM₂₅, and CO exposures simultaneously. All the field evaluation data were collected during two sampling seasons: the summer of 1998 and the winter of 1999.

To measure 1-hr O₃ exposures, a new active O₃ sampler was developed that uses two nitrite-coated filters to measure O₃ concentrations. Laboratory chamber tests found that the active O₃ sampler performed extremely well, with a collection efficiency of 0.96 that did not vary with temperature or relative humidity (RH). In field collocation comparisons with a reference UV photometric monitor, the active O₃ sampler had an effective collection efficiency ranging between 0.92 and 0.96 and a precision for 1-hr measurements ranging between 4 and 6 parts per billion (ppb). The limits of detection (LOD) of this method were 9 ppb-hr for the chamber tests and ~16 ppb-hr for the field comparison tests.

PM_2.5 and CO concentrations were measured using modified continuous monitors—the DustTrak and the Langan, respectively. A size-selective inlet and a Nafion dryer were placed upstream of the DustTrak inlet to remove particles with aerodynamic diameters greater than 2.5 um and to dry particles prior to the measurements, respectively. During the field validation tests, the DustTrak consistently reported higher PM_2.5 concentrations than those obtained by the collocated 12-hr PM_{2 5} PEM samples, by approximately a factor of 2. After the DustTrak response was corrected (correction factor of 2.07 in the summer and 2.02 in the winter), measurements obtained using these methods agreed well with R² values of 0.87 in the summer and 0.81 in the winter. The results showed that the DustTrak can be used along with integrated measurements to measure the temporal and spatial variation in PM_{2 5} exposures. Finally, during the field validation tests, CO concentrations measured using the Langan were strongly correlated with those obtained using the reference method when the CO levels were above the LOD of the instrument [~1 part per million (ppm)].     

Microwave Process for Volatile Organic Compound Abatement

ABSTRACT

The CHA Corporation has completed the U.S. Air Force Phase II Small Business Innovation Research program to investigate the feasibility of using a novel microwave-based process for the removal and destruction of volatile organic compounds (VOCs) in effluents from noncombustion sources, such as paint booth ventilation streams. Removal of solvents by adsorption, followed by the regeneration of saturated granular activated carbon (GAC) by microwave energy, was achieved in a single fixed-bed reactor. Microwave regeneration of the fixed-bed-saturated carbon restored the original GAC adsorption capacity. After 20 adsorption/regeneration cycles, the adsorption capacity dropped from 13.5 g methyl ethyl ketone (MEK)/100 g GAC to 12.5 g MEK/100 g GAC. During microwave regeneration of the GAC fixed bed, the concentrated desorbed paint solvent was oxidized by passing the solvent mixture through a fixed bed of an oxidation catalyst mixed with silicon carbide in a microwave reactor. A 98% oxidation efficiency was consistently achieved from the oxidation of VOCs in the microwave catalytic reactor.     

Decomposition of Gas Phase 1,3-Butadiene by Ultraviolet/Ozone Process

Abstract

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O₃) and ultraviolet (UV)/O₃ technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of ～50 ppm, an ambient temperature of 26 °C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O₃, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo–first-order with respect to BD concentrations. Moisture content (relative humidity = 40–99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

Urban-Center CO Air Quality Projections

The distribution of mutagenic activity and nitroaromatic components of polycyclic organic matter (POM) in ambient air at industrial, urban, suburban, rural, and remote sites was studied using organic extracts from high volume aerosol samples. Direct-acting mutagens including 1-nitropyrene (1-NP), dinitropyrenes (DNP), and hydroxynitropyrenes (HNP) were measured by high performance liquid chromatography while the mutagenicity was determined in the Salmonella bioassay with strain TA-98. Benzo(a)pyrene (BaP), one of the possible precursors of nitroaromatic compounds in POM, was also measured. In comparing samples from a range of sites, TSP and the concentration of BaP per mass of particulate matter decreased, as expected, at greater distances from urban and industrial combustion sources. However, the concentrations of polar nitroaromatic POM compounds per mass of particles were higher at a remote site than in nonindustrial urban and suburban areas. The mutagenicity in particulate matter extracts from the remote area was predominantly (>90 percent) in the very polar fractions. There were also high atmospheric levels of nitroaromatic compounds and mutagenicity in heavily industrialized areas. These observations may reflect the influences of source emissions, atmospheric transformations of POM compounds, and ther atmospheric processes on the composition of ambient suspended particulate matter.     

Evaluation of two models of a slipmeter

The aim of the study was to compare the performances of the Brungraber Mark II (BM II) and Mark III (BM III) slipmeters. Friction measurements with the two slipmeters were conducted in a laboratory using four footwear materials, four floor types, and three surface conditions. Both the coefficient of friction (COF) values obtained with the slipmeters and the force platform-based COF values were measured. The COF measured with the BM II was slightly higher than that measured with the BM III with a R² of 0.83. A comparison of the averaged normal force between the two slipmeters showed that the BM II generated a significantly higher normal force than the BM III at a low COF and the difference of the normal force between the two slipmeters decreased when the COF value was increased. The regression analysis results in this study showed that the force platform-based COF values were closer to the COF values obtained with the BM III than with the BM II. The R² values for the regression model between the COF values obtained from the slipmeter and the force platform were 0.90 and 0.79 for the BM II and BM III, respectively.