A Survey of Nitrogen Dioxide Levels Measured Inside Mobile Homes

As part of the California Mobile Home Study, over 250 mobile homes from throughout the state were monitored for nitrogen dioxide (NO₂) concentrations. Week-long average measurements were taken with Palmes tubes in the kitchen and bedroom of each mobile home during the summer of 1984 and the winter of 1985. The study was conducted entirely by mail with the participants providing all the necessary information. Mobile homes using gas for cooking had significantly higher indoor NO₂ levels than those using electricity. Mobile homes located in the Los Angeles basin had significantly higher indoor NO₂ concentrations than did mobile homes in the rest of the state. Gas cooking, the inverse of the house volume and geographic location (as a surrogate of outdoor NO₂) were the most important variables identified by multiple linear regression.     

The Potential of Pulse-Jet Baghouses for Utility Boilers. Part 2: Performance of Pulse-Jet Fabric Filter Pilot Plants

Pulse-jet fabric filters (PJFFs) are widely used in U.S. industrial boiler applications and in utility and industrial boilers abroad. Their small size and reduced cost relative to more conventional reverse-gas baghouses makes the use of PJFFs appear to be an attractive particulate control option for utility boilers. This paper (Part 2 of a three-part series) summarizes the results of pilot PJFF studies sponsored by the Electric Power Research Institute at different utility sites in the United States. The purpose of these tests is to evaluate PJFF performance for U.S. fossil-fuel-fired applications. These data are also used to corroborate the results of a recent worldwide survey of PJFF user experience, as described in Part 1 of this series. Part 3 will provide a cost comparison of PJFFs to other particulate control options such as electrostatic precipitators and reverse-gas baghouses.     

An Analysis of Biomedical Waste Incineration

The California Air Resources Board (ARB) completed a series of source tests of eight operating biomedical waste incinerators (BMWI) under conditions of typical operation. The emissions of certain metals, and chlorinated dioxins and furans in the flue gases of BMWI are relatively high in comparison to emissions from other combustion sources, such as hazardous waste or municipal waste incinerators of modern design. This study reports on an analysis of the status of the existing regulatory framework and the California data base. Clarification of definitional issues at the federal level is needed to effectively treat BMWI management issues. Although few relationships among combustion parameters and emissions were uncovered, patterns of emissions were evident, suggesting commonality and relationships among the waste stream constituents and emissions. Potential implications for future research, operation of BMWI, controls and source reduction and waste segregation strategies are also discussed.     

The Nonlinearity and Related Band Strength of Carbon Monoxide When Applied in Ambient Air Measurement Using Open Long-Path Fourier Transform Infrared Spectrometry

ABSTRACT

The accuracy of CO concentration determination by open-path Fourier transform infrared (FTIR) spectrometry has been re-evaluated in detail. The evaluation focuses on the correction of the calibration curve—the integrated intensity of a standard spectrum—that is used as a comparison spectrum when doing quantitative analysis of CO. Results show that the calibration curve (with 0.5 cm^-1 or 1 cm^-1 resolution) is apparently inclined to be nonlinear under standard conditions, and that the threshold point of nonlinearity is ~0.1 atm-cm. Two commercial FTIR field monitoring systems have been used to investigate the nonlinearity trend. The experimental method consists of using open-path FTIR systems in combination with nondispersive infrared (NDIR) monitors to establish the calibration curve in a semi-closed corridor. The results have been double-checked using closed-cell dynamic equilibrium systems.

When the optical density is larger than a certain value, the curves begin to bend, and when the optical density approaches zero, the band strength is around 178 ± 3 atm^-1 cm^-2 and 173 ± 2 atm^-1 cm^-2, respectively, for 0.5 and 1 cm^-1 resolution at standard temperature and pressure (STP). These values are quite different from other published data that have been acquired by the pressurized method or by high-resolution     

Laboratory and Field Evaluation of Measurement Methods for One-Hour Exposures to O3, PM25, and CO

ABSTRACT

While researchers have linked acute (less than 12-hr) ambient O₃, PM₂₅, and CO concentrations to a variety of adverse health effects, few studies have characterized short-term exposures to these air pollutants, in part due to the lack of sensitive, accurate, and precise sampling technologies. In this paper, we present results from the laboratory and field evaluation of several new (or modified) samplers used in the “roll-around” system (RAS), which was developed to measure 1-hr O₃, PM₂₅, and CO exposures simultaneously. All the field evaluation data were collected during two sampling seasons: the summer of 1998 and the winter of 1999.

To measure 1-hr O₃ exposures, a new active O₃ sampler was developed that uses two nitrite-coated filters to measure O₃ concentrations. Laboratory chamber tests found that the active O₃ sampler performed extremely well, with a collection efficiency of 0.96 that did not vary with temperature or relative humidity (RH). In field collocation comparisons with a reference UV photometric monitor, the active O₃ sampler had an effective collection efficiency ranging between 0.92 and 0.96 and a precision for 1-hr measurements ranging between 4 and 6 parts per billion (ppb). The limits of detection (LOD) of this method were 9 ppb-hr for the chamber tests and ~16 ppb-hr for the field comparison tests.

PM_2.5 and CO concentrations were measured using modified continuous monitors—the DustTrak and the Langan, respectively. A size-selective inlet and a Nafion dryer were placed upstream of the DustTrak inlet to remove particles with aerodynamic diameters greater than 2.5 um and to dry particles prior to the measurements, respectively. During the field validation tests, the DustTrak consistently reported higher PM_2.5 concentrations than those obtained by the collocated 12-hr PM_{2 5} PEM samples, by approximately a factor of 2. After the DustTrak response was corrected (correction factor of 2.07 in the summer and 2.02 in the winter), measurements obtained using these methods agreed well with R² values of 0.87 in the summer and 0.81 in the winter. The results showed that the DustTrak can be used along with integrated measurements to measure the temporal and spatial variation in PM_{2 5} exposures. Finally, during the field validation tests, CO concentrations measured using the Langan were strongly correlated with those obtained using the reference method when the CO levels were above the LOD of the instrument [~1 part per million (ppm)].     

Microwave Process for Volatile Organic Compound Abatement

ABSTRACT

The CHA Corporation has completed the U.S. Air Force Phase II Small Business Innovation Research program to investigate the feasibility of using a novel microwave-based process for the removal and destruction of volatile organic compounds (VOCs) in effluents from noncombustion sources, such as paint booth ventilation streams. Removal of solvents by adsorption, followed by the regeneration of saturated granular activated carbon (GAC) by microwave energy, was achieved in a single fixed-bed reactor. Microwave regeneration of the fixed-bed-saturated carbon restored the original GAC adsorption capacity. After 20 adsorption/regeneration cycles, the adsorption capacity dropped from 13.5 g methyl ethyl ketone (MEK)/100 g GAC to 12.5 g MEK/100 g GAC. During microwave regeneration of the GAC fixed bed, the concentrated desorbed paint solvent was oxidized by passing the solvent mixture through a fixed bed of an oxidation catalyst mixed with silicon carbide in a microwave reactor. A 98% oxidation efficiency was consistently achieved from the oxidation of VOCs in the microwave catalytic reactor.     

Decomposition of Gas Phase 1,3-Butadiene by Ultraviolet/Ozone Process

Abstract

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O₃) and ultraviolet (UV)/O₃ technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of ～50 ppm, an ambient temperature of 26 °C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O₃, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo–first-order with respect to BD concentrations. Moisture content (relative humidity = 40–99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

Performance measurement for incineration plants using multi-activity network data envelopment analysis: The case of Taiwan

This study proposes the use of multi-activity network data envelopment analysis to appraise how incineration plants in Taiwan perform. Sample data from 2006 is used to examine the trade-offs between efficiency enhancement and pollution abatement. The respective efficiencies of the waste treatment and electricity generation are also assessed in a unified framework. The empirical results indicate that it is more important to improve the efficiency of waste treatment activity than of electricity generation activity in order to enhance the overall performance of Taiwan's incinerators. Since ownership, location and length of operations do not in general affect their performance, any improvement has to come from the careful monitoring of each process of the waste treatment operations. Furthermore, given that the policy in Taiwan has moved away from incineration to recycling, the problem of an over-supply of incinerators may become apparent in the near future. Our results indicate that the availability of capacity size may be an important factor when policy-makers consider whether to close down some existing incinerators.     

Textural and chemical properties of swine-manure-derived biochar pertinent to its potential use as a soil amendment

Biochars have received increasing attention in recent years because of their properties pertaining to soil fertility and contaminant immobilization as well as serving as carbon sinks. In this work, a series of biochars were produced from dried swine manure waste by slow pyrolysis at different temperatures (i.e., 673-1073 K). The characterization of the resulting biochars was examined for its relevance to its potential use as soil amendment. It was found that the pore properties, ash contents and pH values of all swine-manure-derived biochars basically increased as temperature increased, while the yield and nitrogen/oxygen contents decreased with increasing temperature as a result of pyrolytic volatilization during pyrolysis. From the organic and inorganic elements analyses, the manure-derived biochar was rich in soil nutrients such as N, P, Ca, Mg, and K. Furthermore, the pore, surface and chemical properties were also consistent with the observations of the SEM-EDS, XRD and FTIR. This result suggested that the mesoporous manure-derived biochar could be used as an excellent medium to soil environment.