乙醇汽油与普通汽油非常规污染物排放特性对比研究

在一台满足国Ⅴ排放标准的双喷射(气口喷射+缸内直喷)汽油机上开展了燃用E10乙醇汽油(乙醇体积比为10%)对发动机非常规排放特性影响的试验研究.使用傅里叶变换红外分析仪(FTIR)测量了饱和烃、不饱和烃、芳香烃及醇、醛等非常规污染物排放量,对比分析了双喷射模式时各工况下E0和E10两种燃料的非常规排放水平.结果表明,双喷射模式下,加入乙醇有效降低了乙烯、1,3-丁二烯、苯和甲苯的排放量,但会导致乙醛排放升高.双喷射模式下,随着负荷增加,两种燃料下的1,3-丁二烯和甲苯排放呈现先升高后降低的趋势,乙烯、甲醛和苯排放则先降低后升高.乙醇能抑制1,3-丁二烯、乙烯生成,抑制效果为PFI模式优于双喷射模式,GDI模式抑制量最低.PFI和GDI模式下E10的甲醛排放均显著升高,但双喷射模式有效抑制了甲醛排放的增加.     

邢台市秋季PM2.5及水溶性离子污染特征

为研究邢台市秋季PM_2.5污染特征,于2017年10月15日~11月14日在邢台市区对PM_2.5样品进行了采集,并对其中水溶性离子（包括Cl^-、NO₃^-、SO₄^2-、NH₄⁺、Ca²⁺、Na⁺、Mg²⁺、K⁺）进行了分析.结果显示,观测期间邢台市ρ（PM_2.5）平均值为（130.0±74.9）μg/m³,其中水溶性离子质量浓度为（69.8±11.4）μg/m³,占ρ（PM_2.5）的53.3%,NO₃^-、SO₄^2-和NH₄⁺为主要离子,占水溶性离子比例达到了89.7%. 当污染加重,水溶性离子质量浓度随ρ（PM_2.5）增大而升高,且NO₃^-、NH₄⁺及SO₄^2-占比亦逐渐升高,但其他离子占比随之下降,Ca²⁺尤为明显,表明ρ（PM_2.5）升高时主要受二次无机转化影响;观测期间SOR（硫转化率）与NOR（氮转化率）的平均值分别为0.36和0.25,表明秋季SO₂与NO₂转化速率较强,二次无机污染严重,另外SOR及NOR与温度及相对湿度呈正相关,且SOR对二者更为敏感;邢台市秋季PM_2.5呈弱碱性,NH₄⁺主要以（NH₄）₂SO₄和NH₄NO₃的形式存在;ρ（NO₃^-）/ρ（SO₄^2-）平均值为2.13,表明移动源对秋季大气颗粒物的来源贡献较大;PMF分析结果表明,二次转化源、燃烧源及扬尘源为邢台市秋季PM_2.5中水溶性离子的主要来源.     

节水灌溉措施下湘东北丘陵林-稻汇水区复合系统铅的迁移

铅通过食物链的迁移和积累对人类健康的毒害作用日益为社会所重视,而水稻是人类铅摄入的主要途径之一,因此,对稻田土壤铅的迁入途径及其过程特征的研究十分必要.为了探明湖南地区远离城镇、工矿区的丘陵稻区铅的输入、迁移、滞留机制,选择位于湘东北地域的汩罗市桃林林场的林地-山塘-稻田汇水区系统作为研究对象,在水稻大田生长期间,原位研究其大气沉降、岗地径流、山塘水、稻田水、水稻生长等过程的铅通量.结果表明：①输入系统的铅源是大气沉降,其中,在水稻生育前期通过东南季风输入的区域外源铅占90%;②山塘是大气沉降铅的主要集纳地貌单元,存留了大气沉降输入岗地和山塘总铅的66%;③林-稻汇水区系统岗地铅净留存28.8~57.7 g·hm^-2,山塘铅净留存604.3~961.9 g·hm^-2,稻田铅净留存89.6~90.9 g·hm^-2;而对照系统岗地铅净输出173.3 g·hm^-2,山塘净留存3427.6 g·hm^-2,稻田净留存87.1 g·hm^-2;④岗地和山塘对铅的截留量能够互补;⑤从岗地通过径流-山塘水过程迁移到稻田的大分子有机物能够增强稻田对铅的截留.综上所述,丘陵林-稻汇水区系统中铅的循环与大气沉降有关,系统内岗地森林类型、郁闭度、降水产流及泥沙、有机物的输出都会影响铅在系统中的迁移和分配.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Role of glycine on sulfuric acid-ammonia clusters formation: Transporter or participator

Glycine(Gly) is ubiquitous in the atmosphere and plays a vital role in new particle formation(NPF).However,the potential mechanism of its on sulfuric acid(SA)-ammonia(A)clusters formation under various atmospheric conditions is still ambiguous.Herein,a(Gly)_x·(SA)_y·(A)_z(z≤x+y≤3) multicomponent system was investigated by using density functional theory(DFT) combined with Atmospheric Cluster Dynamics Code(ACDC) at different temperatures and precursor concentrations.The results show that Gly,with one carboxyl(-COOH) and one amine(-NH_2) group,can interact strongly with SA and A in two directions through hydrogen bonds or proton transfer.Within the relevant range of atmospheric concentrations,Gly can enhance the formation rate of SA-A-based clusters,especially at low temperature,low [SA],and median [A].The enhancement(R) of Gly on NPF can be up to 340 at T=218.15 K,[SA]=10~4,[A]=10~9,and [Gly]=10~7 molecules/cm~3.In addition,the main growth paths of clusters show that Gly molecules participate into cluster formation in the initial stage and eventually leave the cluster by evaporation in subsequent cluster growth at low [Gly],it acts as an important "transporter" to connect the smaller and larger cluster.With the increase of [Gly],it acts as a "participator" directly participating in NPF.     

Hygroscopicity measurement of sodium carbonate, β-alanine and internally mixed β-alanine/Na2CO3 particles by ATR-FTIR

Water-uptakes of pure sodium carbonate(Na_2CO_3),pure β-alanine and internally mixedβ-alanine/Na_2CO_3 aerosol particles with different mole ratios are first monitored using attenuated total reflectance Fourier transform infrared spectroscopy(ATR-FTIR) technique.For pure Na_2CO_3 aerosol particles,combining the absorptions at 877 and 1422 cm-1 with abrupt water loss shows the efflorescence relative humidity(ERH) of 62.9%–51.9%.Upon humidifying,solid Na_2CO_3 firstly absorbs water to from Na_2CO_3·H2 O crystal at 72.0% RH and then deliquesces at 84.5% RH(DRH).As for pure β-alanine particles,the crystallization takes place in the range of 42.4%–33.2% RH and becomes droplets at ～ 88.2% RH.When β-alanine is mixed with Na_2CO_3 at various mole ratios,it shows no efflorescence of Na_2CO_3 whenβ-alanine to Na_2CO_3 mole ratio(OIR) is 2:1.For 1:1 and 1:2 β-alanine/Na_2CO_3 aerosols,the ERHs of Na_2CO_3 are 51.8%–42.3% and 57.1%–42.3%,respectively.While β-alanine crystal appears from 62.7% RH for 2:1 and 59.4% RH for both 1:1 and 1:2 particles and lasts to driest state.On hydration,the DRH is 44.7%–75.2% for Na_2CO_3 with the OIR of 1:1 and 44.7%–69.0%for 1:2 mixture,and those of β-alanine are 74.8% for 2:1 mixture and 68.9% for two others.After the first dehumidification–humidification,all the water contents decrease despite of constituent fraction.And at ～ 92% RH,the remaining water contents are 92%,89% and 82%at ～ 92% RH,corresponding to OIR of 2:1,1:1 and 1:2 mixed system,respectively.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Fast and efficient aqueous arsenic removal by functionalized MIL-100(Fe)/rGO/δ-MnO2 ternary composites: Adsorption performance and mechanism

Because of its significant toxicological effects on the environment and human health,arsenic(As) is a major global issue.In this study,an Fe-based metal-organic framework(MOF)(Materials of Institut Lavoisier:MIL-100(Fe)) which was impregnated with reduced graphene oxide(rGO) by using a simple hydrothermal method and coated with birnessitetype manganese oxide(δ-MnO_2) using the one-pot reaction process(MIL-100(Fe)/rGO/δ-MnO_2 nanocomposites) was synthesized and applied successfully in As removal.The removal efficiency was rapid,the equilibrium was achieved in 40 min and 120 min for As(Ⅲ) and As(Ⅴ),respectively,at a level of 5 mg/L.The maximum adsorption capacities of As(Ⅲ) and As(Ⅴ) at pH 2 were 192.67 mg/g and 162.07 mg/g,respectively.The adsorbent revealed high stability in pH range 2-9 and saturated adsorbent can be fully regenerated at least five runs.The adsorption process can be described by the pseudo-second-order kinetic model and Langmuir monolayer adsorption.The adsorption mechanisms consisted of electrostatic interaction,oxidation and inner sphere surface complexation.