内质网应激在氟暴露致小鼠睾丸损伤中的作用

探讨了内质网应激在亚慢性氟暴露致小鼠睾丸损伤中的作用及分子机制.选用健康初断乳ICR雄性小鼠30只,随机分为对照组（C）、低氟组（LF）和高氟组（HF）,分别饮用自来水、5、30 mg·L^-1氟化钠水溶液90 d.亚慢性氟暴露结束后,以睾丸脏器系数、睾丸组织氧化/抗氧化酶和形态结构、精子质量、睾丸细胞凋亡、葡萄糖调节蛋白78（GRP78）、CCAAT/增强子结合蛋白同源蛋白（CHOP）、半胱氨酸天冬氨酸蛋白酶12（CASPASE-12）、半胱氨酸天冬氨酸蛋白酶3（CASPASE-3）为观测点.结果表明,与对照组比,LF组和HF组LDH、SOD、T-AOC活性下降,MDA含量上升,HF组GSH-PX活性下降,差异有统计学意义（p<0.05或p<0.01）;LF组可见细胞层次减少、间隙变大,成熟精子数量减少,HF组细胞溶解、层次紊乱,空泡化严重,少见成熟精子;LF组和HF组小鼠的精子活力降低,HF组小鼠精子数量下降,畸形率上升,差异有统计学意义（p<0.05或p<0.01）;LF组和HF组睾丸细胞凋亡指数上升,差异有统计学意义（p<0.01）;LF组和HF组Grp78、Caspase-12、Caspase-3基因表达水平上升,差异有统计学意义（p<0.05或p<0.01）.结果提示,除氧化应激以外,Caspase-12和Caspase-3基因表达异常可能是氟暴露致小鼠睾丸细胞凋亡异常的分子机制之一.     

金属改性对SAPO-34低温还原NO性能的影响

采用浸渍法制备金属改性SAPO-34分子筛催化剂,分析比较了不同单金属（Cu或Co）及不同比例双金属（Cu：Co=1：1、3：1、5：1,质量比）改性催化剂对NO的催化还原性能,评价了不同催化剂的N₂选择性,并采用扫描电子显微镜（SEM）、比表面积测试、X射线衍射分析（XRD）、NH₃-程序升温脱附（NH₃-TPD）等表征手段对催化剂的物化性能进行了分析.结果表明,单金属Cu改性催化剂具有较宽的温度区间,在250~450℃范围内NO的转化率始终保持在100%;双金属改性使NO转化率保持为100%的最低温度下降了25~50℃,显著拓宽了低温段窗口,其中,Cu₃Co₁/SAPO-34催化剂的低温催化还原性能最好,200℃即可实现100%的NO转化率,175℃下的转化率也高达80%以上.Cu-Co双金属改性SAPO-34分子筛催化剂具有优异的低温催化还原NO性能,具有在机动车尾气、工业废气的低温脱硝治理领域应用的潜力.     

核壳结构KNbO3@Co(OH)2的制备及其活化过一硫酸盐降解帕珠沙星的研究

制备了以KNbO₃为载体材料的Co（OH）₂复合材料并对其进行了详细的表征,分析了材料的组成成分、组成形态进而确定了其为核壳结构形貌的KNbO₃@Co（OH）₂.利用合成的样品作为催化剂活化过一硫酸盐（peroxymonosulfate,PMS）来降解帕珠沙星（pazufloxacin,PZF）,结果表明制备的催化剂对PZF的去除效率显著增加.讨论了不同初始PMS剂量对降解效率的影响,发现随着PMS增加可活化生成更多的硫酸根自由基（sulfate radicals,SO₄^·-）和羟基自由基（hydroxyl radicals,HO^·）来降解PZF,但继续增大PMS用量降解效率未见明显提升.酸性和中性pH值条件下利于反应活化PMS降解PZF,而碱性体系减缓反应,甚至强碱体系更易形成Co（OH）₂沉淀不利于反应体系中活性组分CoOH⁺的形成,大大抑制了催化性能.此外,在体系中加入淬灭剂叔丁醇（tert-Butanol,TBA）或者乙醇（ethanol,ETOH）进行自由基的淬灭实验,结果表明SO₄^·-自由基为体系降解PZF过程中主要贡献的自由基,而HO^·自由基的贡献较少.催化剂具有较好的稳定性5次循环之后仍能在10 min之内完全去除PZF.本研究提出了新的思路为制备其他载体的Co（OH）₂核壳结构提供参考依据,同时将该催化剂结合高级氧化技术应用到水体新兴有机污染物净化领域具有很好的应用前景.     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Role of glycine on sulfuric acid-ammonia clusters formation: Transporter or participator

Glycine(Gly) is ubiquitous in the atmosphere and plays a vital role in new particle formation(NPF).However,the potential mechanism of its on sulfuric acid(SA)-ammonia(A)clusters formation under various atmospheric conditions is still ambiguous.Herein,a(Gly)_x·(SA)_y·(A)_z(z≤x+y≤3) multicomponent system was investigated by using density functional theory(DFT) combined with Atmospheric Cluster Dynamics Code(ACDC) at different temperatures and precursor concentrations.The results show that Gly,with one carboxyl(-COOH) and one amine(-NH_2) group,can interact strongly with SA and A in two directions through hydrogen bonds or proton transfer.Within the relevant range of atmospheric concentrations,Gly can enhance the formation rate of SA-A-based clusters,especially at low temperature,low [SA],and median [A].The enhancement(R) of Gly on NPF can be up to 340 at T=218.15 K,[SA]=10~4,[A]=10~9,and [Gly]=10~7 molecules/cm~3.In addition,the main growth paths of clusters show that Gly molecules participate into cluster formation in the initial stage and eventually leave the cluster by evaporation in subsequent cluster growth at low [Gly],it acts as an important "transporter" to connect the smaller and larger cluster.With the increase of [Gly],it acts as a "participator" directly participating in NPF.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Fast and efficient aqueous arsenic removal by functionalized MIL-100(Fe)/rGO/δ-MnO2 ternary composites: Adsorption performance and mechanism

Because of its significant toxicological effects on the environment and human health,arsenic(As) is a major global issue.In this study,an Fe-based metal-organic framework(MOF)(Materials of Institut Lavoisier:MIL-100(Fe)) which was impregnated with reduced graphene oxide(rGO) by using a simple hydrothermal method and coated with birnessitetype manganese oxide(δ-MnO_2) using the one-pot reaction process(MIL-100(Fe)/rGO/δ-MnO_2 nanocomposites) was synthesized and applied successfully in As removal.The removal efficiency was rapid,the equilibrium was achieved in 40 min and 120 min for As(Ⅲ) and As(Ⅴ),respectively,at a level of 5 mg/L.The maximum adsorption capacities of As(Ⅲ) and As(Ⅴ) at pH 2 were 192.67 mg/g and 162.07 mg/g,respectively.The adsorbent revealed high stability in pH range 2-9 and saturated adsorbent can be fully regenerated at least five runs.The adsorption process can be described by the pseudo-second-order kinetic model and Langmuir monolayer adsorption.The adsorption mechanisms consisted of electrostatic interaction,oxidation and inner sphere surface complexation.