太湖北部小流域沉积物重金属污染特征与评价

近几十年来重金属的沉积记录、来源及污染水平受到了广泛关注.为探明太湖北部小流域重金属的污染来源和环境质量状况,本研究分析了柱状沉积物中8种重金属（Mn、Cr、Zn、Cu、As、Pb、Ni和Co）含量.运用主成分分析法判定污染源,富集因子法表征重金属富集特征,通过熵权模糊模型对沉积物中重金属污染状况进行评价.结果显示,所有重金属含量均较高,高低依次为Mn > Cr > Zn > Cu > As > Pb > Ni > Co.其中Mn含量最高,为380.06~767.69μg/g.沉积物重金属污染的主要贡献因子为交通排放、农业污染和煤炭燃烧.As的富集指数最大（2.89~15.61）.其中77.59%的沉积层属于显著富集,受人类活动影响最为显著.熵权模糊综合评价结果表明,Cu（0.483）和As（0.352）的权重值最大,是沉积物中的首要污染物,且65.52%的沉积层重金属含量处于中度污染水平.     

电场与MnxCey催化剂在苯氧化反应中的协同效应及机理探究

挥发性有机物（VOCs）大量排放已成为日益严重的环境问题,为了实现VOCs的高效去除,本文采用自蔓延燃烧合成法制备了一系列锰铈复合氧化物催化剂,将稳恒直流电场引入典型VOCs气体苯的催化氧化过程,并基于不同电场条件下催化剂的理化性质表征结果进行机理分析.实验结果表明,Mn_xCe_y催化剂对含苯废气的去除有良好的效果,稳恒直流电场显著促进了催化剂的活性,其中Mn₁Ce₃的催化性能最佳,电流为5 mA时,Mn₁Ce₃催化剂在155℃可达到50%的苯转化率,在202.4℃可达到90%的苯转化率,对应的转化温度T₅₀和T₉₀比传统方法分别降低了62.4℃和48.3℃,且电场中的反应活化能由52.32 kJ·mol^-1降低至32.31 kJ·mol^-1.根据实验现象及表征结果,发现协同效应与活性位点的快速持续再生及活性氧物种的转化有关,由此提出苯在Mn_xCe_y催化剂上的氧化机理及电场协同催化的反应模型.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

Tuning the fill percentage in the hydrothermal synthesis process to increase catalyst performance for ozone decomposition

The performance of Ce-OMS-2 catalysts was improved by tuning the fill percentage in the hydrothermal synthesis process to increase the oxygen vacancy density. The Ce-OMS-2 samples were prepared with different fill percentages by means of a hydrothermal approach (i.e. 80%, 70%, 50% and 30%). Ce-OMS-2 with 80% fill percentage (Ce-OMS-2-80%) showed ozone conversion of 97%, and a lifetime experiment carried out for more than 20?days showed that the activity of the catalyst still remained satisfactorily high (91%). For Ce-OMS-2-80%, Mn ions in the framework as well as K ions in the tunnel sites were replaced by Ce⁴⁺, while for the others only Mn ions were replaced. O₂-TPD and H₂-TPR measurements proved that the Ce-OMS-2-80% catalyst possessed the greatest number of mobile surface oxygen species. XPS and XAFS showed that increasing the fill percentage can reduce the AOS of Mn and augment the amount of oxygen vacancies. The active sites, which accelerate the elimination of O₃, can be enriched by increasing the oxygen vacancies. These findings indicate that increasing ozone removal can be achieved by tuning the fill percentage in the hydrothermal synthesis process.     

Phosphate recovery with granular acid-activated neutralized red mud: Fixed-bed column performance and breakthrough curve modelling

Granular acid-activated neutralized red mud (AaN-RM) has been successfully prepared with good chemical stability and physical strength. However, its potential for industrial application remains unknown. Therefore, the performance of granular AaN-RM for phosphate recovery in a fixed-bed column was investigated. The results demonstrated that the phosphate adsorption performance of granular AaN-RM in a fixed-bed column was affected by various operational parameters, such as the bed depth, flow rate, initial solution pH and initial phosphate concentration. With the optimal empty-bed contact time (EBCT) of 24.27 min, the number of processed bed volumes and the phosphate adsorption capacity reached 496.95 and 84.80 mg/g, respectively. Then, the saturated fixed-bed column could be effectively regenerated with a 0.5 mol/L HCl solution. The desorption efficiency remained as high as 83.45% with a low weight loss of 3.57% in the fifth regeneration cycle. In addition, breakthrough curve modelling showed that a 5-9-1 feed-forward artificial neural network (ANN) could be effectively applied for the optimization of the fixed-bed adsorption system; the coefficient of determination (R²) and the root mean square error (RMSE) evaluated on the validation-testing data were 0.9987 and 0.0183, respectively. Therefore, granular AaN-RM fixed-bed adsorption exhibits promising potential for phosphate removal and recovery from polluted water.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Mechanism and catalytic performance for direct dimethyl ether synthesis by CO2 hydrogenation over CuZnZr/ferrierite hybrid catalyst

Direct synthesis of dimethyl ether(DME) by CO_2 hydrogenation has been investigated over three hybrid catalysts prepared by different methods:co-precipitation,sol-gel,and solid grinding to produce mixed Cu,ZnO,ZrO_2 catalysts that were physically mixed with a commercial ferrierite(FER) zeolite.The catalysts were characterized by N_2 physisorption,X-ray diffraction(XRD),transmission electron microscopy(TEM),X-ray photoelectron spectroscopy(XPS),temperature programmed desorption of CO_2(CO_2-TPD),temperature programmed desorption of NH_3(NH_3-TPD),and temperature programmed H2 reduction(H_2-TPR).The results demonstrate that smaller CuO and Cu crystallite sizes resulting in better dispersion of the active phases,higher surface area,and lower reduction temperature are all favorable for catalytic activity.The reaction mechanism has been studied using in situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS).Methanol appears to be formed via the bidentate-formate(b-HCOO) species undergoing stepwise hydrogenation,while DME formation occurs from methanol dehydration and reaction of two surface methoxy groups.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.