Toxicity of carbaryl,diquat dibromide,and fluoranthene,individually and in mixture,to larval grass shrimp,Palaemonetes pugio

This study examined the toxicity of two pesticides (carbaryl and diquat dibromide) and one polycyclic aromatic hydrocarbon (fluoranthene), both singly and in mixture, to grass shrimp larvae (Palaemonetes pugio). These three chemicals are all present in coastal environments and can easily enter estuarine ecosystems. Fluoranthene was the most toxic chemical with a 96-h LC₅₀ value of 32.45 μ g/L, followed by carbaryl (43.02 μ g/L) and diquat dibromide (1624 μ g/L). In the chemical mixture tests, the binary carbaryl/diquat dibromide mixture and the ternary carbaryl/diquat dibromide/fluoranthene mixture had additive results.     

Soot Control During the Combustion of Polystyrene

This paper describes an experimental study on the control of soot formation during the combustion of polystyrene (PS). A stable, twodimensional flame generated by using a Wolfhard-Parker type diffusion flame burner was used to simulate practical combustion situations. The combustion characteristics, effects of operating conditions on soot formation, and the effectiveness of various metallic additives as soot suppressants were investigated. It was found that soot yield could not be significantly reduced by controlling the oxidizer (air) flow rate. Increasing the O₂ mole fraction of the oxidlzer increased soot yield under typical operating conditions. However, soot yield could be greatly reduced by adding small amounts of air into the pyrolysis zone of the flame. The additional air would probably increase the combustion reaction rate while decreasing the soot precursor formation rate, thereby causing the observed effect. It was thus suggested that effective soot control could be accomplished by improving mixing between air and the PS devolatilizatlon products In practical combustion situations. The metallic additives tested in this study were the salts of Na, K, Ca, and Ba. Among these salts, Ca was the least effective in reducing soot, and K and Na were nearly equally effective. Ba was much more effective than all the others, and Its effectiveness was strongly dependent on its addition rate.     

Mercury flows in a zinc smelting facility in South Korea

To prepare for the international mercury convention, the characteristics of mercury emissions from a zinc smelting facility in South Korea have been reviewed and a material flow analysis (MFA) has been conducted in this research. As inputs into the mercury MFA study, zinc ores and sulfuric acid were examined, whereas wastewater sludge, effluence water, spent catalyst, and emissions from the casting and roasting processes were examined as outputs. Mercury concentrations extracted from end products like zinc ingots, cadmium ingots, and sulfuric acid were then analyzed. Our results showed that the wastewater sludge discharged from the zinc smelting process had a relatively higher concentration of mercury, indicating that the concentration of mercury was further enriched in the wastewater sludge. The wastes discharged through the zinc smelting process should be thoroughly controlled, as results of the MFA showed that approximately 89 % of the mercury contained in the original input was later found in the waste. According to this study, the higher the concentration of mercury within zinc ores at the input stage, the higher is the mercury concentration found in the wastewater sludge at the output stage.     

Biotreatment of H2S- and NH3-containing waste gases by co-immobilized cells biofilter

Gas mixture of H2S and NH3 in this study has been the focus in the research area concerning gases generated from the animal husbandry and the anaerobic wastewater lagoons used for their treatment. A specific microflora (mixture of Thiobacillus thioparus CH11 for H2S and Nitrosomonas europaea for NH3) was immobilized with Ca-alginate and packed inside a glass column to decompose H2S and NH3. The biofilter packed with co-immobilized cells was continuously supplied with H2S and NH3 gas mixtures of various ratios, and the removal efficiency, removal kinetics, and pressure drop in the biofilter was monitored. The results showed that the efficiency remained above 95% regardless of the ratios of H2S and NH3 used. The NH3 concentration has little effect on H2S removal efficiency, however, both high NH3 and H2S concentrations significantly suppress the NH3 removal. Through product analysis, we found that controlling the inlet ratio of the H2S/NH3 could prevent the biofilter from acidification, and, therefore, enhance the operational stability. Conclusions from bioaerosol analysis and pressure drop in the biofilter suggest that the immobilized cell technique creates less environmental impact and improves pure culture operational stability. The criteria for the biofilter operation to meet the current H2S and NH3 emission standards were also established. To reach Taiwan's current ambient air standards of H2S and NH3 (0.1 and 1 ppm, respectively), the maximum inlet concentrations should not exceed 58 ppm for H2S and 164 ppm for NH3, and the residence time be kept at 72 s.     

Measurement and three-dimensional modeling of airflow and pollutant dispersion in an undersea traffic tunnel

Airflow and pollutant dispersion in a cross-harbor traffic tunnel were experimentally and numerically studied. Concentrations of the gaseous pollutants CO, NOx, and total hydrocarbons (THC) at three axial locations in the tunnel, together with traffic flow rate, traffic speed, and types of vehicle were measured. Three-dimensional (3D) turbulent flow and dispersion of air pollutants in the tunnel were modeled and solved numerically using the finite volume method. Traffic emissions were modeled accordingly as banded line sources along the tunnel floor. The results reveal that cross-sectional concentrations are nonuniformly distributed and that concentrations rise with downstream distance. The piston effect of vehicles alone can provide 9-23% dilution of air pollutants in the tunnel, compounded to a 23-74% dilution effect according to the ventilation condition.     

Effects of the Ellagic acid on the N‐Acetyltransferase activity and Acetylation of 2‐aminofluorene in the rat

The effects of the ellagic acid on the in vitro and in vivo acetylation of 2‐aminofluorene were investigated in male Sprague‐Dawley rats. For in vitro examination, cytosols with or without ellagic acid co‐treatment showed different percentage of 2‐aminofluorene acetylation. For in vivo examination, pre‐treatment of male rats with ellagic acid (10 mg/kg) 24h prior to the administration of 2‐aminofluorene (50 mg/kg) resulted in a 26% and 29%, respectively, decrease in the urinary and fecal recovery of N‐acetyl‐2‐aminofluorene, and a 37% decrease in the metabolic clearance of 2‐aminofluorene to N‐acetyl‐2‐aminofluorene. This is the first demonstration that ellagic acid decrease the N‐acetylation of carcinogens in vitro and in vivo.     

Lead-210 and Beryllium-7 in the Aerosol Particles Around Taiwan Off-Shore Areas

Abstract

Distributions of ²¹⁰Pb and ⁷Be in the aerosol particles of different size fractions were measured around Taiwan offshore areas from October, 1994 to October, 1995. the size distribution and abundance of the aerosol particles showed both spatial and temporal variations. the particle concentrations off northwestern Taiwan were more than twice as those off northeastern Taiwan both in November and March, and the values were much higher in November than in March for both areas. the measured particle concentrations, except for one sample with an unusually high value, ranged from 10 to 83 μOgm ^?3 in the study areas. the ²¹⁰Pb concentrations in the aerosol particles filtered from the air mass varied between 20 × 10^?3 and 72 × 10^?3 dpm m^?3 (1dpm = 0.45 pCi). the ²¹⁰Pb concentrations in the area off southwestern Taiwan appeared somewhat higher than in other areas and were probably contributed by the land air from Taiwan which contains higher ²¹⁰Pb in winter. the ²¹⁰Pb concentrations off northern Taiwan were low in November when the aerosol concentrations were high, but they were high in March when the aerosol concentrations were low.

Based on the ⁷Be monitoring records of 20 years on the aerosol particles of the island by the Taiwan Radiation Monitoring Center, the mean settling rate averaged 0.91, 0.79 and 0.68 cm s^?1, respectively, in northern, central and southern Taiwan. with these values and the ²¹⁰Pb concentrations in the aerosols, the ²¹⁰Pb flux was determined to be between 0.58 and 2.30 dpm cm^?2y^?1, with an average of 1.19 dpm cm^?2y^?1. Excluding the highest value due to its extremely high ²¹⁰Pb and aerosol concentrations, the average is reduced to 1.05 dpm cm^?2y^?1. the activity median diameters (AMD) for ²¹⁰Pb in the study areas were between 0.69 and < 0.49 μM with a mean of 0.5 öm based on ²¹⁰Pb distributions in different particle size fractions. Thus, ²¹⁰Pb was preferentially adsorbed on to the submicron particles. ⁷Be in the study areas showed a good correlation with ²¹⁰Pb in total activity although the two nucides had different sources.     

Improvement of nuclide leaching resistance of paraffin waste form with low density polyethylene

Low-level liquid borate wastes have been immobilized with paraffin wax using a concentrate waste drying system (CWDS) in Korean nuclear power plants. The possibility for improving chemical durability of paraffin waste form was suggested in this study. A small amount of low density polyethylene (LDPE) was added to increase the leaching resistance of the existing paraffin waste form. The influence of LDPE on the leaching behavior of waste form was investigated by performing leaching test according to ANSI/ANS-16.1 procedure during 325 days. It was observed that the leaching of nuclides immobilized within paraffin waste form made a marked reduction although little content of LDPE was added to waste form. The acceptance criteria of paraffin waste form associated with leachability index (LI) and compressive strength after the leaching test were fully satisfied with the help of LDPE.     

Pah characteristics in ambient air within a steel industrial complex

Ambient air samples at ten sites in an iron and steel industrial complex were collected from June to December for analyzing polycyclic aromatic hydrocarbons (PAHs). Sixteen species of PAH components in air samples were identified. The results indicate that both gaseous phase and particle‐bound PAHs at the top of the cokemaking plants are unusually high. The profiles of particle‐bound PAHs indicate that the predominant species at the top of, the coke oven batteries are those of high molecular weight components. The major components of particle‐bound PAHs at sampling sites near the fenceline, however, include the medium molecular weight components. The PAH profiles of air samples within the industrial complex show a strong similarity to those of cokemaking plant samples. The concentrations and the specific content of benzo(a)pyrene in the iron and steel industrial complex are higher than those values measured in urban area, petrochemical industry park, and open‐air burning area.