Use of inert C&D materials for seawall foundation: quality control measures

The technical viability of using inert construction and demolition (C&D) materials for the construction of seawall and breakwater foundations has been established by laboratory testing of the materials, numerical analysis of foundation stability, and a pilot field-scale engineering performance evaluation. However, quality control measures are still required so that only suitable materials are used for seawall and breakwater foundation construction. The development of different quality control measures for different site conditions is presented in this paper. The rationale, practicality, and implementation of these quality control measures are also discussed.     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

The general utilization of scrapped PC board

The traditional burning process is used to recover copper from scrapped PC board (printed circuit board) but it causes serious environmental problems. In this research a new process was developed which not only prevents pollution problems, but also maximizes the utility of all the materials on the waste board. First, the scrapped PC board was crushed and grounded, then placed in the NH₃/NH₅CO₃ solution with aeration in order to dissolve copper. After distilling the copper NH₃/NH₅CO₃ solution and then heating the distilled residue of copper carbonate, pure copper oxide was obtained with particle size of about 0.2 μm and the shape elliptical. The remaining solid residue after copper removal was then leached with 6 N hydrochloric acid to remove tin and lead. The last residue was used as a filler in PVC plastics. The PVC plastics with PC board powder as filling material was found to have the same tensile strength as unfilled plastics, but had higher elastic modulus, higher abrasion resistance, and was cheaper.     

Effects of the type of sintering atmosphere on the chromium leachability of thermal-treated municipal solid waste incinerator fly ash

The sintering process offers an opportunity to combine detoxification and resource recovery for the treatment of municipal solid waste (MSW) incinerator fly ash. However, the chromium (Cr) in the sintered fly ash becomes more readily leachable with increasing sintering time and temperature, thus posing severe threats to the environment and human health when the sintered ash is recycled or reused. This study investigated the enhanced leachability of fly ash containing Cr, by heating the chromium (III) oxide (Cr2O3)-spiked fly ash to 800 degrees C in atmospheres containing air, nitrogen gas (N2), and 5% H2 + 95% N2, respectively. The results indicated that trivalent chromium was converted to its soluble hexavalent form during sintering in the air atmosphere; whereas sintering in a nitrogen atmosphere significantly reduced the leachability of Cr due to lack of oxygen (O2) to oxidize. The effects of the sintering temperature on the total chromium content and the leaching concentration in the toxicity characteristic leaching procedure (TCLP) extract are also discussed.     

负载稀土元素活性碳纤维在微型反应器中净化NO废气

以NH3为还原剂,以活性碳纤维（ACF）、HNO,浸渍的ACF、负载CuO的ACF和负载La2O3的ACF为催化剂,在微型反应器中考察各种催化剂对NO催化还原的活性,并进行了差热-热重、扫描电镜分析。实验结果表明,ACF负载La能有效地改善催化剂的活性,且催化活性中心为非晶态的氧化物;当ACF负载20％的La2O3时具有最好的低温活性,NO的去除率最高可达92％以上。     

Effect of soil solids concentration in batch tests on the partition coefficients of organic pollutants in landfill liner-soil materials

 The effect of the soil solids concentration in batch tests on the measured values of the partition coefficient (K _p) of organic pollutants in landfill liner-soil material was investigated. Since this study was based on the results of batch and column tests conducted independently, there were limitations to the conclusions derived. The organic compounds tested were benzene, methylene chloride, toluene, trichloroethylene, and p-xylene. The results of this study showed that as soil solids concentrations increased, the measured K _p values of these organic compounds strongly decreased. The observed values of K _p stabilized when the soil solids concentration was above a certain value. Typical K _p values obtained from batch tests conducted under high soil solids concentrations were close to those obtained from column tests. It was concluded that the K _p values of organic compounds measured under low soil solids concentrations, i.e., less than 100 g/l, may not correctly simulate the field situation. Consequently, the values of K _p obtained with low soil solids concentrations can result in an overestimation of the retardation factor of the landfill liner material. Received: March 14, 2002 / Accepted: August 25, 2002     

Methodological approach towards the definition of new storage conditions for inert wastes

In 1997, the French Ministry of Environment launched studies aiming to define a specific regulation concerning inert waste disposal in order to limit potential impact of such facilities on the environment by fixing minimum requirements. A model (chemical model/hydrodynamic model) was developed to determine dumping conditions. This model was then applied on two defined scenarios (landfill surface, effective rainfalls...) in order to study the sulphate concentrations in aquifer system immediately downstream from the storage facility. Results allow us to determine in which conditions the sulphates concentrations are compatibles with the potentially drinkable character of the groundwater. They more specifically concern the nature of the waste disposed of, the efficient rainfalls and the landfill area.     

Quantifying dry NH3 deposition to an ombrotrophic bog from an automated NH3 field release system

Providing an accurate estimate of the dry component of N deposition to low N background, semi-natural habitats, such as bogs and upland moors dominated by Calluna vulgaris is difficult, but essential to relate nitrogen deposition to effects in these communities. To quantify the effects of NH₃ inputs to moorland vegetation growing on a bog at a field scale, a field release NH₃ fumigation system was established at Whim Moss (Scottish Borders) in 2002. Gaseous NH₃ from a line source was released along of a 60 m transect, when meteorological conditions (wind speed >2.5 m s^?1 and wind direction in the sector 180–215°) were met, thereby providing a profile of decreasing NH₃ concentration with distance from the source. In a complementary study, using a NH₃ flux chamber system, the relationships between NH₃ concentrations and cuticular resistances were quantified for a range of NH₃ concentrations and micrometeorological conditions for moorland vegetation. Cuticular resistances increased with NH₃ concentration from 11 s m^?1 at 3.0 μg m^?3 to 30 s m^?1 at 30 μg m^?3. The NH₃ concentration data and the concentration-dependent canopy resistance are used to calculate NH₃ deposition taking into account leaf surface wetness. The implications of using an NH₃ concentration-dependent cuticular resistance and the importance for refining critical loads are discussed.     

圆柱体相似试件的拉裂破坏模型研究

首先简单介绍了单轴压缩试验的具体情况。对于拉裂破坏模式,提出了相应的力学计算模型,并建立了抗压强度和抗拉强度的关系式。对于由拉裂面的存在而导致试件最终破坏的计算模型,提出了4种相应的假设。其中,对4种特征的拉裂面建立了抗压强度和抗拉强度的关系式。     

Low-dose irradiation by electron beam for the treatment of high-SOx flue gas on a semi-pilot scale—Consideration of by-product quality and approach to clean technology

Attention has been focused on the treatment of lignite-fired flue gas in order to use lignite in an environmentally friendly way – (i) low-CO₂ emission, (ii) production of a valuable by-product, (iii) no discharge of wastewater, (iv) direct removal of SO₃ (strong toxicity), and (v) treatment of high SO₂ concentration. Based on these criteria, electron beam irradiation with ammonia injection was tested on a semi-pilot scale: 800 Nm³ h^?1 flow rate, 5500 ppm SO₂, 70 ppm NO_x, 22% flue gas moisture, and 75–80 °C at the reactor outlet.As an energy-saving measure, a low dose (5 kGy) of irradiation was applied: the problem lay in the by-product quality. It is considered that (NH₄)₂SO₃ and NH₄HSO₃ produced by thermal reactions are oxidized to form (NH₄)₂SO₄ (fertilizer) by an electron beam. However, not all reactions were complete because the by-product contained small amounts of H₂SO₄ and NH₂SO₃NH₄ (herbicide), so a vegetable pot test was performed to study the by-product quality: no adverse effect was observed. It is inferred from the pot test that slightly acidic soil may protect vegetables from disease and a small amount of NH₂SO₃NH₄ probably affects woody species and not herbaceous species.It is concluded that the electron beam system is noted as a multi-component pollution control process (removal of NO_x, SO₃, SO₂ and dioxins) and this system will contribute to environmentally friendly use of lignite as well as agricultural productivity via fertilizer supply.