Preferred modes of travel among older adults: What factors affect the choice to walk instead of drive?

Introduction

There are many factors that influence older adults' travel choices. This paper explores the associations between mode of travel choice for a short trip and older adults' personal characteristics.

Methods

This study included 406 drivers over the age of 64 who were enrolled in a large integrated health plan in the United States between 1991 and 2001. Bivariate analyses and generalized linear modeling were used to examine associations between choosing to walk or drive and respondents' self-reported general health, physical and functional abilities, and confidence in walking and driving.

Results

Having more confidence in their ability to walk versus drive increased an older adult's likelihood of walking to make a short trip by about 20% (PR = 1.22; 95% CI: 1.06-1.40), and walking for exercise increased the likelihood by about 50% (PR = 1.53; 95% CI = 1.22-1.91). Reporting fair or poor health decreased the likelihood of walking, as did cutting down on the amount of driving due to a physical problem.

Discussion

Factors affecting a person's decision to walk for exercise may not be the same as those that influence their decision to walk as a mode of travel. It is important to understand the barriers to walking for exercise and walking for travel to develop strategies to help older adults meet both their exercise and mobility needs. Impact on Industry: Increasing walking over driving among older adults may require programs that increase confidence in walking and encourage walking for exercise.     

The major accident risk (MAR) process - developing the profile of major accident risk for a large multi national oil company

The paper describes a programme to develop the profile of major accident risk across a large multi national oil company. It describes the concepts, tools and processes for constructing the risk profile and some of the key learnings from the exercise.     

Water quality assessment of Almatti Reservoir of Bijapur (Karnataka State, India) with special reference to zooplankton

The present investigation deals with the limnobiotic status of Almatti reservoir from February, 2003 to January, 2005. The study revealed that, the distribution and population density of zooplankton species depend upon the physico-chemical factors of the environment. Statistical analysis showed that there exists a significant relation between the biological and non-biological factors. The benthic fauna constituting the food of fish can be utilized for extensive culture operation so that the nutrients in the reservoir are not only properly cycled but also serve as a check on further eutrophication.     

Analysis of some heavy metals in the riverine water, sediments and fish from river Ganges at Allahabad

The river Ganges has been one of the major recipients of industrial effluents in India. The present paper deals with the study related to occurrence and bioaccumulation of heavy metals (Cu, Cr, Cd, Pb, Zn) in the riverine water, sediment, and the muscles of two cat fish species, Channa punctatus (C. punctatus) and Aorichthys aor (A. aor) procured from the river Ganges at Allahabad. The data obtained after water analysis reflected the order of occurrence of heavy metals to be Zn > Pb > Cu > Cr > Cd, respectively. The analysis of heavy metals in sediment indicated that among the five heavy metals tested; Zn was maximally accumulated followed by Pb, Cr, Cu and Cd. The trend of heavy metals accumulation in fish muscles was found to be similar to that observed in sediment and water such as Zn > Pb > Cu > Cr > Cd. Data indicated that Zn accumulated maximally in the sediment as well as muscles of both of the fish species in comparison to other metals.     

A novel way to upgrade the coarse part of a high calcium fly ash for reuse into cement systems

Reject fly ash (rFA) represents a significant portion of the fly ashes produced from coal-fired power plants. Due to the high carbon content and large particle mean diameter, rFA is not utilized in the construction sector (for example, as supplementary cementing material) and is currently dumped into landfills, thus representing an additional environmental burden. Recently, the feasibility of using rFA in a relatively small number of applications, like solidification/stabilization of other wastes, has been investigated by different researchers. However, as the overall amount of fly ash utilized in such applications is still limited, there is a need to investigate other possibilities for rFA utilization starting from a deeper understanding of its properties. In the work presented herein, mechanical and hydration properties of cementitious materials prepared by blending the coarse fraction of a lignite high-calcium fly ash with ordinary cement were monitored and compared with the respective ones of a good quality fly ash-cement mixture. The results of this work reveal that a relatively cheap, bilateral classification-grinding method is able to promote the pozzolanic behavior of the rFAs, so that the overall performances of rFA containing cements are drastically improved. The evaluation of these results supports the belief that appropriate utilization of non-standardized materials may lead to new environmental-friendly products of superior quality.     

Waste polyvinylchloride derived pitch as a precursor to develop carbon fibers and activated carbon fibers

Polyvinylchloride (PVC) was successfully recycled through the solvent extraction from waste pipe with an extraction yield of ca. 86%. The extracted PVC was pyrolyzed by a two-stage process (260 and 410 degrees C) to obtain free-chlorine PVC based pitch through an effective removal of chlorine from PVC during the heat-treatment. As-prepared pitch (softening point: 220 degrees C) was spun, stabilized, carbonized into carbon fibers (CFs), and further activated into activated carbon fibers (ACFs) in a flow of CO2. As-prepared CFs show comparable mechanical properties to commercial CFs, whose maximum tensile strength and modulus are 862 MPa and 62 GPa, respectively. The resultant ACFs exhibit a high surface area of 1200 m2/g, narrow pore size distribution and a low oxygen content of 3%. The study provides an effective insight to recycle PVC from waste PVC and develop a carbon precursor for high performance carbon materials such as CFs and ACFs.     

Diel cycles of arsenic speciation due to photooxidation in acid mine drainage from the Iberian Pyrite Belt (Sw Spain)

Twenty four hours diel cycles of arsenic speciation in Acid Mine Drainage (AMD) due to photooxidation have been reported for the first time. AMD samples were taken during 48 h (31st March and 1st April, 2005) at 6 h intervals from the effluent of a massive abandoned polymetallic sulphide mine of the Iberian Pyrite Belt (Sw Spain). Samples were preserved in situ using cationic exchange prior to analysis by coupled high performance liquid chromatography, hydride generation and atomic fluorescence spectrometry (HPLC-HG-AFS) for arsenic speciation. The results indicated the presence of inorganic arsenic species with daily means of 262mugl(-1) for As(V) and 107 microg l(-1) for As(III). No marked diel trend was observed for As(V). However, a marked diel trend was observed for As(III) in the two studied days, with maximum concentrations during nighttime (141-143 microg l(-1)) and minimum concentrations at daytime (72-77 microg l(-1)). This difference in concentration during daytime and nighttime is ca. 100%. A similar diel cycle was observed for iron. An explanation for the arsenic diel cycles observed is the light induced photooxidation of As(III) and the elimination of As(V) due to its adsorption onto Fe precipitates during the daytime. Furthermore, the diel changes in arsenic speciation emphasize the importance of designing suitable sampling strategies in AMD systems.     

Combustion characteristics of Malaysian municipal solid waste and predictions of air flow in a rotary kiln incinerator

Malaysia is in dire need of alternatives to landfilling for solid waste management. Recently, landfills have faced the problems of overfilling, overflowing of leachates leading to pollution of water resources, and uncontrolled dust emissions adversely affecting the local environment. With the rising cost of urbanization coupled with the high rate of waste generation, one possible method of waste treatment that is receiving particular attention by the government is incineration. Incineration of solid waste is rather new in Malaysia, with limited usage in handling small sources of waste generation such as the municipal solid waste (MSW) of resort islands; however, its potential in ameliorating the problems associated with solid waste treatment may make it an attractive alternative to landfill. This article presents the results of test runs conducted to investigate the performance of a locally designed and manufactured rotary kiln incinerator (RKI). The test runs were conducted using MSW collected from the Shah Alam municipality. The combustion efficiency was analyzed by looking at the temperature profiles and chemical species concentrations. To complement the combustion characteristics measurements, predictions of the air flow in the incinerator during the process were also investigated. The overall performance of the RKI suggests that it is suitable for treating MSW.     

Mechanical Property Characterization of Plasticized Sugar Beet Pulp and Poly(Lactic Acid) Green Composites Using Acoustic Emission and Confocal Microscopy

Sorbitol and glycerol were used to plasticize sugar beet pulp-poly(lactic acid) green composites. The plasticizer was incorporated into sugar beet pulp (SBP) at 0%, 10%, 20%, 30% and 40% w/w at low temperature and shear and then compounded with poly(lactic acid) (PLA) using twin-screw extrusion and injection molding. The SBP:PLA ratio was maintained at 30:70. As expected, tensile strength decreased by 25% and the elongation increased. Acoustic emission (AE) showed correlated debonding and fracture mechanisms for up to 20% w/w plasticizer and uncorrelated debonding and fracture for 30–40% sorbitol and 30% glycerol content in SBP–PLA composites. All samples had a well dispersed SBP phase with some aggregation in the PLA matrix. However, at 40% glycerol plasticized SBP–PLA composites exhibited unique AE behavior and confocal microscopy revealed the plasticized SBP and PLA formed a co-continuous two phase system.