Recycling of an industrial sludge and marine clay as light-weight aggregates

The geographical limitations of Singapore, its restricted natural resources and voluminous municipal and industrial waste streams, make environmental management a major challenge for the island state. In an attempt to find ways to reduce importation of raw materials and the waste sent to landfill, light weight aggregates were produced from marine clay and a CaF(2)-rich semiconductor industry sludge. Aggregates were produced in a bench-scale rotary kiln with three clay/sludge loadings (90/10, 70/30 and 50/50%). All three mixtures showed good bloating behavior during firing and the ceramic pellets (1-1.5cm diameter) had densities well below that required for light-weight aggregates. In the initial tests, the pore sizes of the aggregates were in general too large resulting in high water absorption. Comparisons between the composition of the two waste products and the aggregates showed a significant loss of fluorine (40-60%) during processing; a problem which may require flue gas treatment. Leach testing showed that the formed aggregates would not pose a human or environmental hazard in terms of fluorine mobilization.     

Study of the evolution of aerosol emissions from coal-fired power plants due to coagulation, condensation, and gravtitational settling and health impact

This paper studies the scavenging efficiencies of aerosol emissions from coal-fired power plants under different removal mechanisms (coagulation, heterogeneous nucleation and gravitational settling) as a function of time. It also analyses the ‘health impact’ of the aerosol before and after the above dynamic mechanisms by comparing the respirable dust fractions. The well-known equations of evolution are applied to an average PSD that represents the exhaust particulate emissions from coal-fired power plants (i.e. Aboño power plant in Asturias that belongs to Hidrocantábrico Group, S.A.). From this study it is inferred that respirable dust is scavenged with the greatest difficulty and when compared with the initial volume of respirable dust, roughly 20% remains after 18 h of gravitational settling. Therefore, gravitational settling is the main removal mechanism of respirable dust compared to condensation and coagulation.     

Performance Evaluation of Multiple Groundwater Flow and Nitrate Mass Transport Numerical Models

Environmental Modeling & Assessment - Benchmarking of different numerical models simulating groundwater flow and contaminant mass transport is the aim of the present study, in order to...     

Modelling the Distribution and Quality of Sand and Gravel Resources in 3D: a Case Study in the Thames Basin,UK

Three-dimensional (3D) models are often utilised to assess the presence of sand and gravel deposits. Expanding these models to provide a better indication of the suitability of the deposit as aggregate for use in construction would be advantageous. This, however, leads to statistical challenges. To be effective, models must be able to reflect the interdependencies between different criteria (e.g. depth to deposit, thickness of deposit, ratio of mineral to waste, proportion of ‘fines’) as well as the inherent uncertainty introduced because models are derived from a limited set of boreholes in a study region. Using legacy borehole data collected during a systematic survey of sand and gravel deposits in the UK, we have developed a 3D model for a 2400 km² region close to Reading, southern England. In developing the model, we have reassessed the borehole grading data to reflect modern extraction criteria and explored the most suitable statistical modelling technique. The additive log-ratio transform and the linear model of coregionalization have been applied, techniques that have been previously used to map soil texture classes in two dimensions, to assess the quality of sand and gravel deposits in the area. The application of these statistical techniques leads to a model which can be used to generate thousands of plausible realisations of the deposit which fully reflect the extent of model uncertainty. The approach offers potential to improve regional-scale mineral planning by providing an enhanced understanding of sand and gravel deposits and the extent to which they meet current extraction criteria.

     

Framing of Geoengineering Affects Support for Climate Change Mitigation

The growing recognition that climate change mitigation alone will be inadequate has led scientists and policymakers to discuss climate geoengineering. An experiment with a US sample found, contrary to previous research, that reading about geoengineering did not reduce conservatives’ skepticism about the existence of anthropogenic climate change. Moreover, depending on how it is framed, geoengineering can reduce support for mitigation among both conservatives and non-conservatives. When geoengineering is framed as a major solution, people worry less about climate change, leading to reduced mitigation support. When framed as disastrous, people perceived geoengineering as riskier, also leading to a decrease in mitigation support. A more moderate framing of geoengineering as a partial solution is less susceptible to moral hazard effects. Overall, results suggest that geoengineering will not lessen political polarization over anthropogenic climate change, and could undercut support for mitigation efforts. Instead, framing geoengineering as a small piece to solving a big puzzle seems to be the best strategy to weaken this potential moral hazard.     

Trace elements and microbiological parameters in farmed Nile tilapia with emphasis on muscle,water, sediment and feed

Fish may bioaccumulate contaminants from the aquatic environment and extend them to the food chain provoking risks to human health. This study evaluated the microbiological parameters of the pond´s water and trace elements concentrations in samples of water, sediment, feed and muscle of farmed Nile tilapia used for human consumption in southern Brazil. A total of 240 fish were collected from 12 tilapia farms. Sediment, tank water and dry ration used in the animals' diet were collected for analysis. Analysis were performed by Energy Dispersion X-ray Fluorescence (EDXRF), Inductively Coupled Plasma Mass Spectrometer (ICP-MS), Induced Coupled Plasma Optical Emission Spectrometer (ICP-OES), and Atomic Absorption Spectrometer (AAS-VGA). In addition, the microbiological analysis of the water was carried out. The concentrations of Se, I, Fe, Cu and Zn in fish muscle were higher than the recommended by the Brazilian legislation, considering the advised daily intake for adults. The arsenic element had concentrations above the limit stipulated by the present Brazilian legislation, observed in all samples of muscle, sediment and tank water highlighting a possible environmental and fish contamination by the toxic element. Moreover, the arsenic concentration in the water presented a positive correlation (ρ?=?0.33) with arsenic in the muscle, suggesting that tilapia is a good environmental bioindicator, once they properly reflect the levels of arsenic in the water. It is suggested to perform an arsenic speciation for quantification of the inorganic form and accurate assessment of the degree of toxicity in the muscle samples and risks it can bring to human health. Regarding the other potentially toxic elements (Hg, Pb and Cd), and microbiological analysis of water it was verified that the consumption of the fish in question does not raise risks, since the values are within a quality benchmark established by law. The concentration of total and fecal coliforms in pond´s water in the facilities was in agreement with the microbiological indexes required by the legislation of CONAMA class II. Western region presented the lowest concentrations of fecal coliforms when compared to the other regions. There was no significant difference in the microbiological counts of total heterotrophic bacteria, Vibrio spp. and Pseudomonas spp. among the regions.     

Auxinic herbicides induce oxidative stress on Cnesterodon decemmaculatus (Pisces: Poeciliidae)

Environmental Science and Pollution Research - Pesticides might increase the production of reactive oxygen species (ROS). Dicamba (DIC) and 2,4-dichlorophenoxyacetic acid (2,4-D) are auxinic...     

Synthesis of functionalized mesoporous material from rice husk ash and its application in the removal of the polycyclic aromatic hydrocarbons

Environmental Science and Pollution Research - The rice husk ash (RHA) was used as an alternative source of silica for the synthesis of the functionalized mesoporous material, which was used in the...     

Low‐concentration hydrogen peroxide decontamination for Bacillus spore contamination in buildings

Remediation and recovery efforts after a release of Bacillus anthracis (anthrax) spores may be difficult and costly. In addition, response and recovery technologies may be focused on critical resources, leaving the small business or homeowner without remediation options. This study evaluates the efficacy of relatively low levels of hydrogen peroxide vapor (HPV) delivered from off‐the‐shelf equipment for the inactivation of Bacillus spores within an indoor environment. Decontamination evaluations were conducted in a house using both Bacillus atrophaeus var. globigii (Bg; as surrogates for B. anthracis) inoculated on the carpet and galvanized metal as coupons and Geobacillus stearothermophilus (Gs) as biological indicators on steel. The total decontamination time ranged from 4 to 7 days. Using the longer exposure times, low concentrations of HPV (average levels below 20 parts per million) effectively inactivated Bg and Gs spores on the materials tested. The HPV was generated with commercial humidifiers and household‐strength hydrogen peroxide solutions. The presence of home furnishings did not have a significant impact on HPV efficacy. This simple, inexpensive, and effective decontamination method could have significant utility for remediation following a B. anthracis spore release, such as following a terrorist attack.     

Evaluation of the effects of PFAS soil adsorption and transformation in the presence of divalent cations under ambient conditions

A bench‐scale study was conducted to evaluate the effect of divalent cations on the adsorption of perfluoroalkyl and polyfluoroalkyl substances (PFAS) onto soil particles. The study entailed batch testing of a synthetic soil mixture under a range of Epsom salt (soluble magnesium sulfate heptahydrate) concentrations. The synthetic soil was produced using a mix of sand, silt, clay, and organic matter that then was mixed and saturated with water collected from a PFAS‐impacted water source. The results indicate that variable concentrations of magnesium (divalent cation) had a minor effect on the sorption of perfluorooctane sulfonate with the highest sorption occurring in the strongest solution of Epsom salt. An unanticipated result of the test involved apparent biomediated transformation of polyfluorinated alkylated sulfonates (fluorotelomers or FTS) to perfluorooctanoic acid, perfluoroheptanoic acid (PFHpA), and perfluorononanoic acid. We believe this is the first time the complete transformation of 6:2 FTS to PFHpA has been observed and reported under ambient surface water‐like conditions within 6 months, a relatively short timeframe.