Airborne Particulate Emissions from a Chromic Acid Anodizing Process Tank

Particulate mass concentration, particle size distribution, and particle chemical composition measurements have been conducted on the gases exhausting from a chromic acid anodizing process tank. Particle mass concentrations in the 200 to 20,000 μg/m³ range were measured using open-faced filters (47 mm diameter) adjacent to the process tank liquid and with closed filters (90 mm diameter) in the exhaust duct. Particle size distributions, measured using University of Washington Mark 3 and Mark 20 Cascade Impactors, showed the particle aerodynamic mass median diameter was about 3 microns. Chemical analysis of the particle samples obtained by the Modified EPA Method 5 sampling train, the Mark 20 UW Cascade Impactors, and by the 47 mm and 90 mm diameter filters showed Cr⁺⁶ concentrations in the 20 to 1,500 μg/m³ range with over 99 percent of the chromium in particles larger than 1.0 microns diameter. An integrating nephelometer was used to measure the light scattering coefficient of the exhaust gases upstream of the wet scrubber. The light scattering coefficient increased by a factor of about 2–3 over the background level during the 40 minute time period while a part was being anodized. The bscat values ranged from 3 × 10^?5 to 3 × 10^?4 meters^?1 for the aerosol particles less than about 6 microns aerodynamic diameter.     

Development of Cleanup Standards at Superfund Sites: An Evaluation of Consistency

The Washington Department of Ecology (WDOE) recently developed a regulatory program for determining cleanup standards at hazardous waste sites. One of WDOE's first tasks in the development of a cleanup standards program was to evaluate how standards have been developed and implemented under Superfund.

The evaluation of cleanup standards revealed: (1) a great deal of variation among sites, both in the magnitude of the standards set for some contaminants and the basis on which they were set, and (2) that there is no consistent decision-making approach for determining how standards should be set. This lack of consistency and guidance has the potential to result in overly stringent or underprotective cleanup requirements and inefficient standard development.

Washington State has adopted an approach that allows for implementing uniform numerical cleanup standards at relatively straightforward sites and provides a process for establishing site-specific cleanup levels at more complex sites. This approach is expected to facilitate development of standards that offer appropriate human health and ecological protection while minimizing private and public sector site management and cleanup costs.     

Measurement of Volatile Organics at Part per Billion Concentrations Using a Cold Trap Inlet and High Speed Gas Chromatography

Direct inlet gas chromatography (GC) is becoming one of the most frequently used techniques for measurement of volatile organics in air. Although GC is an effective tool, its usefulness as a field method can be limited by retention times of several minutes or more, and by the limits of detection. In order to address these issues, a high speed GC system featuring a capillary cold trap inlet and variable speed electrometeramplifier was developed and tested.

The gas cooled inlet was used to collect and focus organic vapors from injection volumes of up to 1 ml. Resistance heating of the metal cold trap produced a narrow injection band that allowed simple separations to be completed in 5 to 20 seconds. Use of a variable speed electrometer-amplifier allowed the response time and noise suppression characteristics to be adjusted to the needs of the specific analysis.

Simple mixtures of organics including aromatics, alkanes and chlorinated hydrocarbons were separated in 20 seconds or less. The limits of detection for 13 test compounds ranged from less than 1 part per billion by volume (ppbv) to about 50 ppbv. Data presented here indicate that high speed GC using a cold trap inlet may be a feasible approach for near real-time measurement of volatile organics in ambient air.     

Assessment of Needs for Technical Information in EPA’s Hazardous and Solid Waste Programs

Headquarters managers and Regional staff in the U.S. Environmental Protection Agency’s hazardous and solid waste programs were surveyed to determine priorities for technical information and guidance among EPA Regional staff, state hazardous waste management staff, EPA contractors, and the regulated community. The survey also examined delivery systems effective for EPA Regional staff. The fifteen highest ranked technical needs for RCRA, Superfund, and UST reflect a pervasive interest in hazardous waste remediation. Top priority technical needs focus on establishing cleanup levels, subsurface fate and transport, field monitoring and quality assurance, remedy selection, and most importantly, which remedies work and which do not in specific situations. Technical needs of non- EPA audiences are quite similar to those for EPA field staff. Preferences for technology transfer delivery systems are generally for conventional distribution methods (such as print materials and workshops) rather than electronic or video media. Regional staff report serious problems in utilizing technology transfer because of time constraints, insufficient knowledge of available products, insufficient travel funds, and limited access to and training on computers.     

An Analysis of Biomedical Waste Incineration

The California Air Resources Board (ARB) completed a series of source tests of eight operating biomedical waste incinerators (BMWI) under conditions of typical operation. The emissions of certain metals, and chlorinated dioxins and furans in the flue gases of BMWI are relatively high in comparison to emissions from other combustion sources, such as hazardous waste or municipal waste incinerators of modern design. This study reports on an analysis of the status of the existing regulatory framework and the California data base. Clarification of definitional issues at the federal level is needed to effectively treat BMWI management issues. Although few relationships among combustion parameters and emissions were uncovered, patterns of emissions were evident, suggesting commonality and relationships among the waste stream constituents and emissions. Potential implications for future research, operation of BMWI, controls and source reduction and waste segregation strategies are also discussed.     

Moving Bed Adsorption System for Control of VOCs from an Aircraft Painting Facility

An activated carbon moving bed system (10 to 100 acf m air flow) was tested for controlling VOC emissions from a commercial aircraft painting facility. The cross-flow moving adsorbent bed showed a VOC collection efficiency in the 77.1 to 99.6 percent range over a superficial gas velocity range of 27 to 185 ft/min (0.14-0.94 m/sec). The collection efficiencies were neither affected by a change in carbon flow rates from 5 to 8 Ib/hr (2.3 to 3.6 kg/hr) nor by a change in the gas superficial velocity from 27 to 185 ft/min. The VOC concentration in the emission stream from the painting hangar was found to vary by at least a factor of 20 (from 0.18 to 15 ppm) both over the five month period (during which the 15 system tests of about three hours each were conducted) and within a single eight hour work shift.     

Wind Tunnel Modelling of Roadways: Comparison with Mathematical Models

The assessment of air quality impacts from roadways is a major concern to urban planners. In order to assess future road and building configurations, a number of techniques have been developed, including mathematical models, which simulate traffic emissions and atmospheric dispersion through a series of mathematical relationships and physical models. The latter models simulate emissions and dispersion through scaling of these processes in a wind tunnel. Two roadway mathematical models, HIWAY-2 and CALINE-4, were applied to a proposed development in a large urban area. Physical modelling procedures developed by Rowan Williams Davies & Irwin Inc. (RWDI) in the form of line source simulators were also applied, and the resulting carbon monoxide concentrations were compared. The results indicated a factor of two agreement between the mathematical and physical models. The physical model, however, reacted to changes in building massing and configuration. The mathematical models did not, since no provision for such changes was included in the mathematical models. In general, the RWDI model resulted in higher concentrations than either HIWAY-2 or CALINE-4. Where there was underprediction, it was often due to shielding of the receptor by surrounding buildings. Comparison of these three models with the CALTRANS Tracer Dispersion Experiment showed good results although concentrations were consistently underpredicted.     

Estimating Maximum Concentrations for Open Path Monitoring Along a Fixed Beam Path

ABSTRACT

Researchers have applied open path optical sensing techniques to a variety of workplace and environmental monitoring problems. Usually these data are reported in terms of a path-average (or path-integrated) concentration. When assessing potential human exposures along a beam path, this path-average value is not always informative, since concentrations along the path can vary substantially from the beam average. The focus of this research is to arrive at a method for estimating the upper-bound in contaminant concentrations over a fixed open beam path. The approach taken here uses a statistical model to estimate an upper-bound concentration based on a combination of the path-average and a measure of the spatial variability computed from point samples along the beam path. Results of computer simulations and experimental testing in a controlled ventilation chamber indicate that the model produced conservative estimates for the maximum concentration along the beam path. This approach may have many applications for open path monitoring in workplaces or wherever maximum concentrations are a concern.     

Innovative Approach for Estimating Fugitive Gaseous Fluxes Using Computed Tomography and Remote Optical Sensing Techniques

ABSTRACT

This paper presents a new approach to quantify emissions from fugitive gaseous air pollution sources. The authors combine Computed Tomography (CT) with Path-Integrated Optical Remote Sensing (PI-ORS) concentration data in a new field beam geometry. Path-integrated concentrations are sampled in a vertical plane downwind from the source along several radial beam paths. An innovative CT technique, which applies the Smooth Basis Function Minimization method to the beam data in conjunction with measured wind data, is used to estimate the total flux from the fugitive source. The authors conducted a synthetic data study to evaluate the proposed methodology under different meteorological conditions, beam geometry configurations, and simulated measurement errors. The measurement errors were simulated based on data collected with an Open-Path Fourier Transform Infra-Red system. This approach was found to be robust for the simulated errors and for a wide range of fluctuating wind directions. In the very sparse beam geometry examined (eight beam paths), successful emission rates were retrieved over a 70° range of wind directions under extremely large measurement error conditions.     

A Comparative Analysis of Emissions Deterioration for In-Use Alternative Fuel Vehicles

Abstract

Although there have been several studies examining emissions from in–use alternative fuel vehicles (AFVs), little is known about the deterioration of these emissions over vehicle lifetimes and how this deterioration compares with deterioration from conventional vehicles (CVs). This paper analyzes emissions data from 70 AFVs and 70 CVs operating in the federal government fleet to determine whether AFV emissions deterioration differs significantly from CV emissions deterioration. An analysis is conducted on three alternative fuel types (natural gas, methanol, and ethanol) and on four pollutants (carbon monoxide, total hydrocarbons, non-methane hydrocarbons, and nitrogen oxides). The results indicate that for most cases studied, deterioration differences are not statistically significant; however, several exceptions (most notably with natural gas vehicles) suggest that air quality planners and regulators must further analyze AFV emissions deterioration to properly include these technologies in broader air quality management schemes.