Comparison of the Annular Denuder System and the Transition Flow Reactor for Measurements of Selected Dry Deposition Species

An intensive field study was conducted in Research Triangle Park, North Carolina in the fall of 1986. Ambient concentrations of the following constituents were obtained: nitric acid, nitrous acid, nitrogen dioxide, sulfur dioxide, ammonia, hydrogen ion, and particulate nitrate, sulfate, and ammonium. Results collected using the annular denuder system (ADS) and the transition flow reactor (TFR) are presented and compared.

Both types of samplers had operational detection limits on daily (22-hour) samples that were generally below 1 μg m_-3 suggesting that both samplers can provide sensitive measurements for most of the constituents of interest. Both the ADS and TFR show reasonable (>25 percent) within-sampler precision for most of the measured species concentrations, except TFR fine particulate nitrate measurements where results were frequently negative (The TFR fine particulate nitrate measurement is calculated using subtraction of positive numbers).

Comparison of ADS and TFR daily results showed good agreement for total particulate sulfate, the sum of total (coarse plus fine) particulate and gaseous nitrate, and ammonia. As a result of different inlet particle collection efficiencies, the ADS fine particulate sulfate exceeded the TFR (5 percent). In the absence of a filter to collect volatilized particulate ammonium in the ADS, the sum of total particulate and gaseous ammonium in the TFR exceeded that in the ADS. Of potentially more importance, ADS measurements of SO₂ and H⁺ exceeded those of the TFR, while TFR measurements of HNO₃ exceeded those of the ADS. Results of this study suggest that the TFR may provide biased measurements of SO₂, H⁺, HNO₃, and Fine NO₃ ^- that cannot be corrected without modifications to the fundamental design of the sampling system.     

Validation of Models for Predicting Formaldehyde Concentrations in Residences due to Pressed-Wood Products

This paper describes a laboratory project to assess the accuracy of emission and indoor air quality models to be used in predicting formaldehyde (HCHO) concentrations in residences due to pressed-wood products made with urea-formaldehyde bonding resins. The products tested were partlcleboard underlayment, hardwood- plywood paneling and medium-density fiberboard (mdf). The products were initially characterized in chambers by measuring their formaldehyde surface emission rates over a range of formaldehyde concentrations, air exchange rates and two combinations of temperature and relative humidity (23° C and 5 0% RH; 26°C and 60% RH). They were then installed in a two-room prototype house in three different combinations (underlayment flooring only; underlayment flooring and paneling; and underlayment flooring, paneling, and mdf). The equilibrium formaldehyde concentrations were monitored as a function of air exchange rate. Particleboard underlayment and mdf, but not paneling, behaved as the emission model predicted over a large concentration range, under both sets of temperature and relative humidity. Good agreement was also obtained between measured formaldehyde concentrations and those predicted by a mass-balance indoor air quality model.     

A Management Systems Review of the Superfund RI/FS: Opportunities for Streamlining

The Management Systems Review is an important component of EPA’s quality assurance program. MSRs enable managers to assess the effectiveness of environmental data operations and the quality assurance/ quality control activities designed to ensure that the results are of the expected quality. These reviews inform managers about aspects of the environmental data operation that are working well and those which may warrant some improvement. A recent review of the Superfund remedial investigation/feasibility study (RI/FS) has shown that the MSR is an excellent tool for providing a systematic definition of complex environmental data operations and for enabling a thorough analysis of these operations. The MSR utilized information gathered from interviews of Regional staff and management and from case studies of recently completed RI/FSs. The findings indicated that environmental data play an important role in most RI/FS decisions and that thorough and structured scoping is critical to the effectiveness of the RI/ FS. Analysis of the RI/FS process using a comprehensive flow model identified several opportunities for changes that may increase efficiency in data collection and the reliability of RI/FS decisions. These changes provide for more effective scoping activities, a streamlined feasibility study, and increased use of treatability studies during the RI. A pilot demonstration of these process changes is being planned for a Regional RI/FS.     

An Evaluation of the Effects of Ozone Injury on Radial Growth of Ponderosa Pine (Pinus ponderosa) in the Southern Sierra Nevada

Growth of ponderosa pines with visible symptoms of ozone injury was compared with that of asymptomatic trees in the southern Sierra Nevada, California. Time series analysis indicated that there was no significant reduction in annual radial increment of symptomatic trees during recent years compared to past growth and growth of asymptomatic trees. First order autocorrelation and climatic variables accounted for a large proportion of the variance in growth index, and winter precipitation was positively correlated with growth for all size and age classes. Although ozone concentrations are high enough to cause chlorosis and premature needle senescence in ponderosa pine, there has been no significant change in growth associated with ozone injury.     

Determination of Room Temperature OH Rate Constants for Acetylene,Ethylene Dichloride,Ethylene Dibromide,p-Dichlorobenzene and Carbon Disulfide

A relative rate procedure was used to measure hydroxyl rate constants at room temperature in the presence of oxygen. The photolysis of methyl nitrite in the presence of nitric oxide was used to generate OH radicals. The rate of loss of the test compounds was measured relative to that of ethane (k_OH = 2.74 × 10^-13 cm³ molec^-1 s^-1). The rates obtained at 297 ± 2 K are: acetylene = (7.8 ± 1.6) × 10^-13 cm³ molec^-1 s^-1,1,2-dichloroethane (2.8 ± Q.6) × 10^-13 cm³ molec^-1 s^-1, 1,2-dibromoethane (2.4 ± 0.5) × 10^-13 cm³ molec^-1 s^-1, p-dichlorobenzene (4.3 ± 0.9) × 10^-13 cm³ molec^-1 s^-1 and carbon disulfide (29 ± 6) × 10^-13 cm³ molec^-1 s^-1. Under a proposed EPA rule, this OH rate determination procedure could be used to determine if a given volatile organic will be subject to control for reduction of photochemical ozone.     

Transportation-Related Volatile Hydrocarbon Source Profiles Measured in Atlanta

Abstract

Samples representative of transportation-related hydrocarbon emissions were collected as part of the 1990 Atlanta Ozone Precursor Monitoring Study. Motor vehicle emissions were sampled in canisters beside a roadway in a tunnel-like underpass during periods of heavy traffic. Airport and aircraft emissions were approximated by canister samples obtained at a major airport facility. Three octane grades of gasoline were purchased from six major vendors in Atlanta. Canister samples were prepared using these fuels to approximate the whole gasoline and gasoline vapor composition of the fuels in use during the study. All samples were analyzed by gas chromatography/flame ionization detection (GC/FID) for their hydrocarbon content. Detailed speciated hydrocarbon profiles were developed from this source sampling and analysis program for use in the Chemical Mass Balance (CMB) model. Profiles presented and discussed here represent the hydrocarbon composition of emissions from a roadway, composite headspace gasoline at two temperatures, composite whole gasoline, whole gasoline at three octane grades, and an airport. The roadway profile is compared with similar profiles in the literature, and recommendations are made regarding its use in the CMB model. The roadway and fuel profiles are discussed in the context of the MOBILE5 model outputs. The headspace gasoline vapor profile presented here is compared with a headspace gasoline vapor profile calculated from the whole gasoline profile by means of Raoult’s law. Agreement between the measured and calculated headspace profiles is excellent. The airport profile demonstrates the importance of high molecular weight volatile hydrocarbons in airport and aircraft emissions.     

Limestone Dissolution in Flue Gas Scrubbing: Effect of Sulfite

Batch limestone dissolution experiments were carried out in a pH stat apparatus at 55°C with CO2 sparging and dissolved sulfite. Particle size distribution, utilization, sulfite in solution, limestone type, and the approach to calcite equilibrium were all found to contribute to the limestone reactivity. In the absence of sulfite, limestone dissolution was controlled solely by mass transfer. For a given stone under mass transfer control, film thickness was found to be independent of pH. The dissolution rate in the presence of sulfite was controlled by a combined surface kinetics/mass transfer regime. SEM micrographs supported this conclusion. A surface rate correlation was developed which accounted for observed inhibition by an inverse dependence on calcium sulfite concentration at the limestone surface. While the form of the rate expression was applicable to all stones, the surface rate constant was stone dependent. A computer code which accounted for mass transfer with surface kinetics was tested against experimental observations of four limestone types. Changes in pH and the concentrations of calcium, carbonate, sulfite, sulfate, and adipic acid were accurately modeled.     

The Potential of Pulse-Jet Baghouses for Utility Boilers. Part 2: Performance of Pulse-Jet Fabric Filter Pilot Plants

Pulse-jet fabric filters (PJFFs) are widely used in U.S. industrial boiler applications and in utility and industrial boilers abroad. Their small size and reduced cost relative to more conventional reverse-gas baghouses makes the use of PJFFs appear to be an attractive particulate control option for utility boilers. This paper (Part 2 of a three-part series) summarizes the results of pilot PJFF studies sponsored by the Electric Power Research Institute at different utility sites in the United States. The purpose of these tests is to evaluate PJFF performance for U.S. fossil-fuel-fired applications. These data are also used to corroborate the results of a recent worldwide survey of PJFF user experience, as described in Part 1 of this series. Part 3 will provide a cost comparison of PJFFs to other particulate control options such as electrostatic precipitators and reverse-gas baghouses.     

Flow Injection Analysis of MWC Fly Ash Leaching Characteristics

Abstract

A completely mixed batch reactor leaching method utilizing flow injection analysis (the CMBR-FIA method) was developed to study the lead leaching characteristics of municipal waste combustor fly ash. Flow injection analysis (FIA) coupled with atomic absorption spectrophotometry enabled the determination of lead concentrations at one minute intervals. The pH and oxidation-reduction potential of the solution were continuously monitored to characterize the leaching conditions. Automatic titration was used to alter the solution pH to defined endpoints. The CMBR-FIA method offers the ability to immediately observe alterations to the leaching solution, and grants the freedom to study a number of parameters concurrently. The CMBR-FIA method is a rapid and reliable means to investigate leaching characteristics. This paper describes the method and demonstrates its use to monitor the leaching of lead from municipal solid waste combustor fly ash as a function of pH. Soluble lead concentrations are shown to increase quickly with decreasing pH.

A maximum of 50% of the total lead concentration was available in solution at pH 2. This value gradually decreased with time to over 35% of the total.