Review of indoor emission source models. Part 1. Overview

Indoor emission source models are mainly used as a component in indoor air quality (IAQ) modeling, which, in turn, is part of exposure and risk modeling. They are also widely used to interpret the experimental data obtained from environmental chambers and buildings. This paper compiles 52 indoor emission source models found in the literature. Together, they represent the achievements that IAQ modelers have made in recent years. While most models have a certain degree of usefulness, genuine predictive models are still few, and there is undoubtedly much room for improvement. This review consists of two parts. Part 1--this paper-provides an overview of the 52 models, briefly discussing their validity, usefulness, limitations, and flaws (if any). Part 2 focuses on parameter estimation, a topic that is critically important to modelers but has not been systematically discussed.     

Dissociation of sulfur hexafluoride tracer gas in the presence of an indoor combustion source

As an odorless, nontoxic, and inert compound, sulfur hexafluoride (SF6) is one of the most widely used tracer gases in indoor air quality studies in both controlled and uncontrolled environments. This compound may be subject to reactions with water vapor under elevated temperature to form acidic inorganic compounds such as HF and H2SO4. Thus, in the presence of unvented combustion sources such as kerosene heaters, natural gas heaters, gas log fireplaces, candles, and lamps, the SF6 dissociation may interfere with measurements of the emissions from these sources. Tests were conducted in a research house with a vent-free natural gas heater to investigate these potential interferences. It was observed that the heater operation caused about a 5% reduction of SF6 concentration, which can be an error source for the ventilation rate measurement and consequently the estimated pollutant emission rates. Further analysis indicates that this error can be much greater than the observed 5% under certain test conditions because it is a function of the ventilation flow rate. Reducing the tracer gas concentration has no effect on this error. A simple theoretical model is proposed to estimate the magnitude of this error. The second type of interference comes from the primary and secondary products of the SF6 dissociation, mainly H2SO4, SO2, HF, and fine particulate matter (PM). In the presence of approximately 5 ppm SF6, the total airborne concentrations of these species increased by a factor of 4-10. The tests were performed at relatively high SF6 concentrations, which is necessary to determine the interferences quantitatively. The second type of interference can be significantly reduced if the SF6 concentration is kept at a low ppb level.     

生物焦炭滴滤塔降解苯乙烯废气的中试启动研究

苯乙烯废气既是一种挥发性有机化合物（VOCs），又属于我国恶臭气体控制的范围之内。其作为一种化工原料和有机溶剂广泛应用于工业生产中。生物法处理有机废气具有运行费用低和没有二次污染等优点。采用焦炭填料滴滤塔对苯乙烯废气的处理进行了中试启动研究。启动过程中，进气浓度范围是50—114mg／m^3，去除率为30％～45％左右，最高可达90％左右。所采用的焦炭填料可以认为是一种环境友好型填料，废弃后可作为燃料，值得推广。     

Improving urban air quality in China: Beijing case study

China is undergoing rapid urbanization because of unprecedented economic growth. As a result, many cities suffer from air pollution. Two-thirds of China's cities have not attained the ambient air quality standards applicable to urban residential areas (Grade II). Particulate matter (PM), rather than sulfur dioxide (SO2), is the major pollutant reflecting the shift from coal burning to mixed source pollution. In 2002, 63.2 and 22.4% of the monitored cities have PM and SO2 concentrations exceeding the Grade II standard, respectively. Nitrogen oxides (NOx) concentration kept a relatively stable level near the Grade II standard in the last decade and had an increasing potential in recent years because of the rapid motorization. In general, the air pollutants emission did not increase as quickly as the economic growth and energy consumption, and air quality in Chinese cities has improved to some extent. Beijing, a typical representative of rapidly developing cities, is an example to illustrate the possible options for urban air pollution control. Beijing's case provides hope that the challenges associated with improving air quality can be met during a period of explosive development and motorization.     

废气治理的低温等离子体-催化协同净化技术

低温等离子体 催化协同净化技术具有能耗低、投资少、处理效率高、不产生二次污染等显著优点备受人们的关注。从挥发性有机化合物 (VOC)的转化、氮氧化合物的脱除、汽车尾气净化等不同废气治理的角度 ,概括了目前国内外在这方面的研究进展 ,最后提出了该项技术在环境保护领域的应用前景及研究方向     

油泥废弃物的生物修复技术研究

本文利用正交试验 ,探讨了堆腐法处理油泥废弃物过程中调控因子 (肥料、客土、水分和 pH)的影响。结果发现 ,投加一定量的客土是影响处理效果的重要因子。通过正交试验选择和确定的最佳处理条件为 :在自然温度 >2 0℃的情况下 ,客土投加量 2 0 %、肥料 10 %、菌剂 5 %、控制水分 30 % (烘干基 )和pH 7。优化条件的建立为油泥废弃物的深度处理提供了理论依据     

改进的硫酸盐-聚乙烯醇法包埋藻菌脱氮除磷研究

采用改进的硫酸盐-PVA固定化法将藻与菌混合固定。在三种不同藻菌比的情况下，固定化系统对氮去除均可达100％，但是去除速度与固定的细菌量有关，细菌量越大，对氮的去除速度越快；对磷的去除随实验进行，最大去除率逐步下降，其下降速度与固定藻的量有关，藻量越大，下降速度越慢。由此说明脱氮的主要贡献者是细菌，而藻对除磷起了主要作用。为达到有效的脱氮除磷，应适当提高固定化藻的浓度，藻菌比应大于2：1。透射电镜照片显示，在聚乙烯醇载体上，藻类的生长没有受到限制。     

超细TiO2粒子的超滤分离及回用特性

针对TiO2超细粒子的超滤分离特性进行了试验研究,探讨了操作压力、膜面流速、TiO2投量、pH、电解质等参数条件对膜通量的影响规律及作用机理,证实了浓差极化及滤饼层阻力是影响通量变化的主导因素,在此基础上确定了适宜的超滤工艺条件及膜清洗方式.以甲基橙为降解基质分别测试了经混凝与超滤分离后的TiO2光催化活性,结果表明,超滤不仅可实现TiO2粒子与水的彻底分离,且分离后TiO2催化活性与初次使用相当.研究表明超滤用于悬浮光催化体系的固液分离及催化剂再用是可行的.     

非定态SO2制酸工艺在铅精矿烧结烟气治理中的应用

介绍了非定态SO2制酸工艺的特点、流程及其在铅精矿烧结烟气治理中的应用效果。该工艺具有良好的社会效益、环境效益和较好的经济效益，具有较高的推广应用价值。     

用于粉煤灰排放的加湿卸灰设备

针对粉煤灰排放产生二次污染问题，经过分析比较，选用了科学的加湿排放工作原理，设计了用于粉煤灰排放的新型灰料加湿卸灰机。