Bioremediation of kerosene I: A case study in liquid media

The ability of different local isolates in addition to some isolates from Germany to degrade kerosene in liquid medium was studied. The results showed that the percent of kerosene degradation varied among the different organisms and that 59–94% of kerosene was degraded after 21 d. Two local isolates (Pseudomonas sp. AP and Pseudomonas sp. CK) and one German isolate (Gordonia sp. DM) were selected for this study. The addition of wheat bran, as co-substrate, stimulated the kerosene degradation by the two local strains, while glucose inhibited the degradation rate using the three organisms with different rates. Ammonium nitrate and urea was the best nitrogen sources. The use of superphosphate (as phosphorus source) in the presence of urea stimulates the degradation rate. It was also observed that the addition of 1% surfactants, like Triton X-100, Igepal, Tergitol, or Tween 20 and 80 enhanced the kerosene degradation. The degradation percent lied between 94% and 98%. The ability of the tested organisms to degrade kerosene concentration from 2% to 8% was evaluated. It was found that the three organisms degraded about 65–85% from 8% kerosene after 21 d. The use of rice straw-immobilized cells reduced the time of degradation and enhanced the degradation ability of the organisms. The sodium dodecyl sulphate-polyacrylamide gel electrophoresis revealed the presence of a common protein band when the tested organisms were grown on kerosene.     

A batch study on the bio-fixation of carbon dioxide in the absorbed solution from a chemical wet scrubber by hot spring and marine algae

Carbon dioxide mass transfer is a key factor in cultivating micro-algae except for the light limitation of photosynthesis. It is a novel idea to enhance mass transfer with the cyclic procedure of absorbing CO(2) with a high performance alkaline abosorber such as a packed tower and regenerating the alkaline solution with algal photosynthesis. Hence, the algae with high affinity for alkaline condition must be purified. In this study, a hot spring alga (HSA) was purified from an alkaline hot spring (pH 9.3, 62 degrees C) in Taiwan and grows well over pH 11.5 and 50 degrees C. For performance of HSA, CO(2) removal efficiencies in the packed tower increase about 5-fold in a suitable growth condition compared to that without adding any potassium hydroxide. But ammonia solution was not a good choice for this system with regard to carbon dioxide removal efficiency because of its toxicity on HSA. In addition, HSA also exhibits a high growth rate under the controlled pHs from 7 to 11. Besides, a well mass balance of carbon and nitrogen made sure that less other byproducts formed in the procedure of carboxylation. For analysis of some metals in HSA, such as Mg, Mn, Fe, Zn, related to the photosynthesis increased by a rising cultivated pH and revealed that those metals might be accumulated under alkaline conditions but the growth rate was still limited by the ratio of bicarbonate (useful carbon source) and carbonate. Meanwhile, Nannochlopsis oculta (NAO) was also tested under different additional carbon sources. The results revealed that solutions of sodium/potassium carbonate are better carbon sources than ammonia carbonate/bicarbonate for the growth of NAO. However, pH 9.6 of growth limitation based on sodium was lower than one of HSA. The integrated system is, therefore, more feasible to treat CO(2) in the flue gases using the algae with higher alkaline affinity such as HSA in small volume bioreactors.     

Risk assessment of trace elements in the stomach contents of Indo-Pacific Humpback Dolphins and Finless Porpoises in Hong Kong waters

The potential health risks due to inorganic substances, mainly metals, was evaluated for the two resident marine mammals in Hong Kong, the Indo-Pacific Humpback Dolphin (Sousa chinensis) and the Finless Porpoise (Neophocaena phocaenoides). The stomachs from the carcasses of twelve stranded dolphins and fifteen stranded porpoises were collected and the contents examined. Concentrations of thirteen trace elements (Ag, As, Cd, Co, Cr, Cs, Cu, Hg, Mn, Ni, Se, V and Zn) were determined by inductively coupled plasma mass spectrometer (ICP-MS). An assessment of risks of adverse effects was undertaken using two toxicity guideline values, namely the Reference Dose (RfD), commonly used in human health risk assessment, and the Toxicity Reference Value (TRV), based on terrestrial mammal data. The levels of trace metals in stomach contents of dolphins and porpoises were found to be similar. Risk quotients (RQ) calculated for the trace elements showed that risks to the dolphins and porpoises were generally low and within safe limits using the values based on the TRV, which are less conservative than those based on the RfD values. Using the RfD-based values the risks associated with arsenic, cadmium, chromium, copper, nickel and mercury were comparatively higher. The highest RQ was associated with arsenic, however, most of the arsenic in marine organisms should be in the non-toxic organic form, and thus the calculated risk is likely to be overestimated.     

Microbial degradation and impact of Bracken toxin ptaquiloside on microbial communities in soil

The carcinogenic and toxic ptaquiloside (PTA) is a major secondary metabolite in Bracken fern (Pteridium aquilinum (L.) Kuhn) and was hypothesized to influence microbial communities in soil below Bracken stands. Soil and Bracken tissue were sampled at field sites in Denmark (DK) and New Zealand (NZ). PTA contents of 2.1 +/- 0.5 mg g(-1) and 37.0 +/- 8.7 mg g(-1) tissue were measured in Bracken fronds from DK and NZ, respectively. In the two soils the PTA levels were similar (0-5 microg g(-1) soil); a decrease with depth could be discerned in the deeper B and C horizons of the DK soil (weak acid sandy Spodosol), but not in the NZ soil (weak acid loamy Entisol). In the DK soil PTA turnover was predominantly due to microbial degradation (biodegradation); chemical hydrolysis was occurring mainly in the uppermost A horizon where pH was very low (3.4). Microbial activity (basal respiration) and growth ([3H]leucine incorporation assay) increased after PTA exposure, indicating that the Bracken toxin served as a C substrate for the organotrophic microorganisms. On the other hand, there was no apparent impact of PTA on community size as measured by substrate-induced respiration or composition as indicated by community-level physiological profiles. Our results demonstrate that PTA stimulates microbial activity and that microorganisms play a predominant role for rapid PTA degradation in Bracken-impacted soils.     

A field trial for an ex-situ bioremediation of a drilling mud-polluted site

The remediation of drilling mud-polluted sites in the Southeast of Mexico is a top priority for Mexican oil industry. The objective of this work was to find a technology to remediate these sites. A field trial was performed by composting in biopiles, where four 1ton soil-biopiles were established, one treatment in triplicate and one unamended biopile. Amended biopiles were added with nutrients to get a C/N/P ratio of 100/3/0.5 plus a bulking agent (straw) at a soil/straw ratio of 97/3. Moisture content was maintained around 30-35%. Results showed that, after 180 d, total petroleum hydrocarbon (TPH) concentrations decreased from 99300+/-23000mgTPHkg(-1) soil to 5500+/-770mgTPHkg(-1) for amended biopiles and to 22900+/-7800mgTPHkg(-1) for unamended biopile. An undisturbed soil control showed no change in TPH concentrations. Gas chromatographic analysis showed residual alkyl dibenzothiophene type compounds. Highest bacterial counts were observed during the first 30 d which correlated with highest TPH removal, whereas fungal count increased at the end of the experimentation period. Results suggested an important role of the straw, nutrient addition and water content in stimulating aerobic microbial activity and thus hydrocarbon removal. This finding opens an opportunity to remediate old polluted sites with recalcitrant and high TPH concentration.     

Dioxin screening in fish product by pattern recognition of biomarkers

Two alternative, cost- and time-effective dioxin screening methods relying on two categories of potential lipid biomarkers were investigated. A dioxin range varying from 1.1 to 47.1 pg PCDD/F TEQ-WHO/g lipid using 64 fish meal samples was used for model calibration. The methods were based on multivariate models using either (1) fatty acid composition monitored by GC-FID or (2) fluorescence landscape signals analysed using the PARAFAC model and in both cases predicting dioxin content as pgPCDD/F TEQ-WHO/g lipid. In both cases, Partial Least Squares (PLS) regression was performed for predicting the dioxin content of a sample. The GC-FID data analyses was based on automatic peak alignment and integration, enabling extraction of the area of 140 peaks from the gas chromatograms, as opposed to the 31 fatty acids usually considered for fish oil characterisation. In addition to classic PLS employing the whole dataset for calibration, a two-step local PLS modeling approach was performed based upon an initial selection of k number of calibration samples providing the best match to the prediction sample using a so-called k Nearest Neighbors (kNN) approach, then followed by PLS calibration on these kNN selected samples for dioxin prediction. Fluorescence spectroscopy offers a promising non-invasive and ultra-rapid technique, with less than two minutes analysis time. However, fluorescence spectroscopy using the pattern recognition "kNN-PLS" yielded a correlation of 0.76 (r2) and a high root mean square error of prediction of 11.4 pg PCDD/F TEQ-WHO/g lipid. The predictions were improved when the PLS calibration was performed on all the sample with a root mean square error of prediction of 7.0 pg PCDD/F TEQ-WHO/g lipid. Unfortunately, these results failed to demonstrate the potential of fluorophore monitoring as a screening method. In contrast, the overall best screening performance was obtained with the fatty acid profile, when the kNN-PLS combination employed for pattern recognition (kNN) all the areas of the 140 detected peaks and the PLS regression used the areas of 46 selected peaks. This "kNN-PLS" prediction with three latent variables and based upon the 12 nearest neighbors selected out of the 64 x 2 fatty acid profiles (duplicate analyses), yielded a correlation of 0.85 (r2) and a root mean square error of prediction of 2.1 pg PCDD/F TEQ-WHO/g lipid and resulted in a total analysis time of one and half hour per sample.     

Electrochemical degradation applied to the metabolites of Acid Orange 7 anaerobic biotreatment

The electrochemical oxidation of the biotic degradation products of the textile dye C.I. Acid Orange 7 (AO7) was achieved using a boron doped diamond electrode (BDD). Tests were performed with model solutions of the biotic degradation products, sulphanilic acid (SA) and 1-amino-2-naphthol (AN), and also with real effluents obtained in experiments carried out in an up-flow anaerobic sludge blanket (UASB) reactor, fed with a simulated textile effluent containing AO7, working in mesophilic or thermophilic conditions. Bulk electrolysis was studied using two different supporting electrolytes - NaCl and Na(2)SO(4). The influence of initial metabolite concentration and current density on the electrodegradation rates of the biotic products was investigated. For the UASB effluents, oxidation tests were carried out for different electrolytes and at different current densities. Samples were collected at pre-selected intervals and absorbance measurements, chemical oxygen demand (COD) and total organic carbon (TOC) tests and high performance liquid chromatography (HPLC) analysis were performed. Results have shown an almost complete elimination of the persistent pollutants and a COD removal higher than 70% for both AN and SA. For the UASB effluents, COD removals between 45% and 90% and TOC removals varying from 19% to 41% were obtained.     

Ozone pre-treatment as improver of PAH removal during anaerobic digestion of urban sludge

Polycyclic aromatic hydrocarbons are ubiquitous persistent pollutants. They may accumulate in sludge during wastewater treatment because of their low biodegradability and their hydrophobic characteristics. Combination of ozonation and anaerobic digestion may be efficient to remove PAHs naturally present in sludge. The objective of this study was to investigate the impact of ozone pre-treatment, with and without surfactant addition, on the anaerobic degradation of 12 PAHs (from low to high molecular weight). Under anaerobic digestion without ozonation pre-treatment, the highest removals were obtained for the lightest PAHs (3-aromatic rings). Ozonation pre-treatment of sludge allowed to increase biodegradability or bioavailability of each PAH, and the PAH removals were well correlated to the PAH solubility. Finally, addition of tyloxapol before sludge ozone pre-treatment had antagonist effects on PAH removal during anaerobic digestion: negative impact on anaerobic ecosystem activity and improvement of PAH bioaccessibility (particularly the PAHs with the highest octanol water partition coefficients).     

Sulfidation treatment of molten incineration fly ashes with Na2S for zinc, lead and copper resource recovery

The present study focuses on the conversion of heavy metals involved in molten incineration fly ashes to metal sulfides which could be thereafter separated by flotation. The sulfidation treatment was carried out for five molten incineration fly ashes (Fly ash-A to Fly ash-E) by contacting each fly ash with Na(2)S solution for a period of 10 min to 6h. The initial molar ratio of S(2-) to Me(2+) was adjusted to 1.20. The conversion of heavy metals to metal sulfides was evaluated by measuring the S(2-) residual concentrations using an ion selective electrode. The formation of metal sulfides was studied by XRD and SEM-EDS analyses. In the case of Fly ash-A to Fly ash-D, more than 79% of heavy metals of zinc, lead and copper was converted to metal sulfides within the contacting period of 0.5h owing to a fast conversion of metal chlorides to metal sulfides. By contrast, the conversion of about 35% was achieved for Fly ash-E within the same contacting period, which was attributed to a high content of metal oxides. Further, the S(2-) to Me(2+) molar ratio was reduced to 1.00 to minimize Na(2)S consumption and the conversions obtained within the contacting period of 0.5h varied from 76% for Fly ash-D to 91% for Fly ash-C. Finally, soluble salts such as NaCl and KCl were removed during the sulfidation treatment, which brought about a significant enrichment in metals content by a factor varying from 1.5 for Fly ash-D to 4.9 for Fly ash-A.     

Effect of pre-treatment and supporting media on Ni(II), Cu(II), Al(III) and Fe(III) sorption by plant root material

In this work Paspalum notatum root material was used to elucidate the influence of acid leaching pre-treatment and of sorption medium on metal adsorption. Ground P. notatum root was leached with 0.14M HNO(3). Leached root material (LRM) and non-leached root material (NLRM) were employed to flow sorption of Ni(II), Cu(II), Al(III) and Fe(III) in 0.5M CH(3)COONH(4) medium at pH 6.5. For LRM the sorption was also studied in 0.5M KNO(3) medium. The acid pre-treatment increased the sorption capacity (SC) for all ions studied. For the KNO(3) medium, Cu(II) and Fe(III) sorption was higher than in CH(3)COONH(4) and the type of the Ni(II) isotherm's model changed. The Freundlich model was the most representative isotherm model to describe metallic ions sorption. The (1)H NMR spectra showed differences between LRM and NLRM and the acid-basic potentiometric titration elucidated that acid-leaching procedure affected the root material sorption sites once only two predominant sorption sites were found for LRM (phenolic and amine, both able cations sorption) and five sorption sites (two carboxylic, amine and two phenolic) were founded for NLRM.