Designating Air Quality Management Areas (AQMAs) in the UK Implications for Securing UK Air Quality Objectives

Across the United Kingdom, the majority of local authoritieshave now completed their first phase of local air qualityreview and assessment work, as required under the AirQuality Strategy for England, Scotland, Wales and NorthernIreland (DETR, 2000a). Emerging from this first phasework is an anticipated suite of over 110 Air QualityManagement Areas (AQMAs). These areas are identifiedlocations where one or more of the national air qualityobjectives are predicted to exceed by specific target dates,and their spatial extent and shape is emerging as highlyvariable. Local authorities are guided to use a variety ofscientific tools to underpin the scientific assessments, anda consideration of uncertainty in both the tools used andsubsequent delineation of AQMAs is likely to affect theemerging management areas significantly. With subsidiarity underpinning the process of local air qualitymanagement (LAQM), local decision-making is anticipated toinfluence the outcome of the LAQM process in its entirety,with the declaration of AQMAs necessitating the preparationand implementation of air quality action plans. UKexperience of the effective management of local air quality,through the designation of AQMAs, demonstrates a valuableframework for other European countries developing mechanismsto manage air quality locally.     

Use of Natural 35S to Trace Sulphate Cycling in Small Lakes,Flattops Wilderness Area,Colorado, U.S.A.

Measurements of the cosmogenically-produced ³⁵S, a radioisotope of sulphur (t_1/2 = 87 days), are reported for the Ned Wilson Lake watershed in Colorado. The watershed contains two small lakes and a flowing spring presumed to be representative of local ground water. The watershed is located in the Flattops Wilderness Area and the waters in the system have low alkalinity, making them sensitive to increases in acid and sulphate deposition. Time series of ³⁵S measurements were made during the summers of 1995 and 1996 (July–September) at all three sites. The system is dominated by melting snow and an initial concentration of 16–20 mBq L^-1 was estimated for snowmelt based on a series of snow samples collected in the Rocky Mountains. The two lakes had large initial ³⁵S concentrations in July, indicating that a large fraction of the lake water and sulphate was introduced by meltwater from that year's snowpack. In 1995 and 1996, ³⁵S concentrations decreased more rapidly than could be accounted for by decay, indicating that other processes were affecting ³⁵S concentrations. The most likely explanation is that exchange with sediments or the biota was removing ³⁵S from the lake and replacing it with older sulphate devoid of ³⁵S. In September of 1995 and 1996, ³⁵S concentrations increased, suggesting that atmospheric deposition is important in the sulphate flux of these lakes in late summer. Sulphur-35 concentrations in the spring water were highly variable but never higher than 3.6 mBq L^-1 and averaged 2 mBq L^-1. Using a simple mixing model, it was estimated that 75% of the spring water was derived from precipitation of previous years.     

Assessment of sampling and chemical analysis of source-separated organic household waste

The quality of the waste sampling procedure and chemical analysis was evaluated in a research program on characterization of organic waste obtained after disc screening of source-separated organic household waste. The sampling procedures focused on a truckload of waste and involved several steps of subsampling including shredding, mixing, blending, high-speed-blending, drying and milling prior to analysis of the organic waste with respect to ash content, crude fibers, crude fat, crude protein, sugar, starch, enzyme-digestible organic matter, P, N, C, H, S and calorific value. The statistical evaluation of the procedures involved 10 samples of the same truckload of waste obtained by splitting the sample at each level in the procedure according to a staggered, incomplete nested statistical design. Furthermore, one sample was analysed six times over a period of approximately one year. The statistical evaluation showed that no single step in the sampling procedure contributed with excessive variance and that the variance caused by the sampling procedure was approximately the same as the variance in the chemical analysis observed over a year. The variance varied with the analytical parameter but for most parameters the uncertainty was satisfactorily low (of the order of 3-10% expressed as the relative standard deviation, which is considered to be satisfactory for waste characterization).     

Lightweight Concrete Containing an Alkaline Resistant Starch-Based Aquagel

Starch aquagel-based lightweight concrete has properties similar to those of other lightweight concrete products. However, starch aquagels are unstable in the strongly alkaline conditions typical of Portland Cement-based concrete and may interfere with the setting process. The effect of alkali treatments on the physical, mechanical, and functional properties of starch aquagels and aquagels from starch/polymer blends was investigated. Starch was blended at 100–115°C in a twin-screw extruder with five different polymers to determine whether the blends improved alkaline resistance. Polymer blends containing 5%, 15%, and 30% of the polymer hydrated and formed aquagels when equilibrated in water for 24 h. However, equilibrium moisture content was lower for the blends compared to the starch control. Aquagels equilibrated in 0.15 N NaOH swelled, lost compressive strength and had greater than 90% moisture. The blend of starch and 30% PVOH absorbed less moisture and was more resistant to alkaline dissolution in 1 N NaOH than the other blends tested making it a more suitable material for aquagel-based concrete. The moisture content of starch-based aquagels and mixing time were critical factors in determining setting times. The size of aquagel blends had a minor effect on density and compressive strength.     

Utilization of magnetic and electrostatic separation in the recycling of printed circuit boards scrap

The progress of the technology is directly related to the growth of production and consumption of electrical/electronics equipment, especially of personal computers. This type of equipment has a relatively short average lifetime, 2-3 years. The amount of defective or obsolete equipment has been increasing substantially; consequently its disposition and/or recycling should be studied. In this work, printed circuit boards, which are used in personal computers, were studied in order to recover the metals in the circuit boards through mechanical processing, such as crushing, screening, as well as magnetic and electrostatic separation. The results obtained demonstrate the feasibility of using these processes to separate metal fractions from polymers and ceramics, and that it is possible to obtain a fraction concentrated in metals containing more than 50% on average of copper, 24% of tin and 8% of lead.     

Novel Sorbent of Sand Coated with Humic Acid-Iron Oxide Nanoparticles for Elimination of Copper and Cadmium Ions from Contaminated Water

Journal of Polymers and the Environment - Nanoparticles of humic acid and iron oxide were impregnated on the inert sand to produce sorbent for treating groundwater contained of cadmium and copper...     

Preliminary Studies on Converting Agricultural Waste into Biodegradable Plastics—Part IV: Polysaccharide Containing Natural Materials

Corn distillers’ dry grain, corncob powder, hardwood powder, and sugar beet pulp were separately anionized by oxidation with sodium hypochlorite in aqueous solution. Solid reaction products instantly precipitated upon admixing each of the above-oxidized materials with soy protein isolate. Infrared spectra and differential scanning calorimetry supported the hypothesis that soy protein isolate complexed with all of the above-oxidized polysaccharides. Reaction products with either oxidized corn distillers’ dry grain or oxidized sugar beet pulp provided hard, brittle pellets with tensile strengths as high as 9.5 MPa, suggesting that these materials could be viable as biodegradable plastics.