Environmental Impact Assessment of Polylactide(PLA)/Chicken Feathers Biocomposite Materials

The aim of this study is to analyse the environmental impacts (EIs) of the process of preparation of new biocomposite materials obtained from polylactide (PLA) and chicken feathers (CFs). Two CFs stabilization methods and different percentages of CFs have been studied. The EIs of these new composites were compared to the impact of virgin PLA. Cradle-to-gate life cycle inventories were assessed for 0–35% v/v of CFs in a CFs/PLA biocomposite. Two CFs stabilization processes, autoclave and surfactant, were tested and compared with the aim to prioritize one of them from the environmental point of view. A composite plate of 184?×?184?×?2.2 mm³ was defined as the functional unit. Autoclave stabilization process exhibited lower environmental impact compared with surfactant stabilization process mainly due to both the lower requirements of electricity and water and the reduced pollution loads of the generated wastewater. Thus, the autoclave process was selected as the standard method when comparing the EIs of the proposed CFs/PLA biocomposites. In this sense, the addition of CFs to PLA matrix proportionally reduces all the EIs compared to pure PLA due to the replacement of PLA with CFs. This behaviour can be explained because the PLA production accounts for the 99% of the impact of the biocomposite. Consequently, CFs conveniently stabilized might be an alternative raw material to prepare CFs/PLA biocomposites with less environmental impact compared to pure PLA.     

Interannual Changes in the C:N:P Ratios of Seston and Zooplankton of a High Mountain Lake in Sierra Nevada,Spain

We investigated the carbon, nitrogen and phosphorus content inthe seston and the zooplankton of a high-mountain lake duringthree years of contrasting physical and chemical conditions.Carbon in seston was ten times higher in 1995 than in 1996 and1997. Phosphorus content in seston was variable for the studyperiod, increasing gradually towards late summer in 1995, butpeaking abruptly in 1996 and 1997, reflecting atmosphericdepositions. Seston C:P were high and did not fit any definitepattern in 1995, and were particularly low after the thaw, increasing towards mid-summer in 1996 and 1997. As the seasonprogressed, major decreases in these ratios occurred coincidingwith important atmospheric inputs in the lake area. ZooplanktonN:P and C:P were negatively associated to the appearance ofrotifers and copepod nauplii in 1995, but positively correlatedto the ontogenetic development of the most abundant species,Mixodiaptomus laciniatus, in 1996. Seasonal variations inzooplankton N:P and C:P ratios showed limited interannual, butlarge intraannual variability. The comparison between the bulkcarbon in seston and zooplankton demands for this elementindicated that zooplankton were above food-quantity thresholdsfor maximum growth in 1995, 1996 and mid-season of 1997,therefore suffering only from food-quantity constraints afterthe thaw (nauplii dominance) and towards late season (adultdominance) in the latter year. The high C:P ratios in sestonrelative to zooplankton in 1995 imply that the zooplankton mayhave faced severe food-quality constraints (in terms ofphosphorus) during this year. Differences between bulkzooplankton and seston elemental nutrients are also discussed inrelation to the competitive abilities of species, andparticularly of Daphnia.     

Effect of Cross-Linking Waste Protein with Diepoxides on its Biodegradation under Anaerobic Conditions

Biodegradability testing was performed in an aqueous environment under anaerobic conditions after inoculation with digested sludge from municipal wastewater treatment plant. In cross-linking with 1,2:3,4-diepoxybutane in limits 0.8–9.1% weight, biodegradability degree decreased from 76.8 to 62.2%; when 1,2:7,8 diepoxyoctane in quantities 1.1–13.2% weight was used, biodegradability degree dropped more prominently – from 72.3 to 22.8%. There is obviously a direct connection between growing cross-link degree (assessed by so-called fixation index) and decreasing readiness to biodegradation, apparently owing to build-up of a network forming an obstacle to access of micro-organisms and enzymes.     

Sulfur Metabolism in Polluted Sphagnum Peat Bogs: A Combined 34S–35S–210Pb Study

The size and isotopic behavior of sulfur pools in²¹⁰Pb-dated peat cores were investigated to obtain aninsight into retention mechanisms of pollutant S in twomountain-top peatlands of the Northern Czech Republic, CentralEurope. The bogs were situated 40 km apart in an area whichbetween the years 1985 and 1995 received as much as 130 kg Sha^-1 yr^-1 from the atmosphere. Vertical peataccretion was faster at Pod Jelení horou (JH) than atVelký moál (VM). Organic carbon-bonded S was themost abundant sulfur pool, constituting 77 and 65 wt. % at JHand VM, respectively. At JH both the S concentration maximumand the highest annual S deposition rate were displaceddownward by more than 20 years (from 1987 to the 1960s)indicating that the buried S is vertically mobile. At VM the Sconcentration was the highest in the topmost 2-cm section eventhough atmospheric S deposition peaked in 1987. Differentmechanisms of S isotope redistribution prevailed in thetopmost peat layers at JH, where a negative ³⁴Sshift occurred, and at VM, where a positive ³⁴Sshift occurred. Bacterial sulfate reduction was responsiblefor the negative ³⁴S shift at JH. One possibleexplanation of the positive ³⁴S shift at VM isrelease of ³²S-enriched products of mineralization duringpeat diagenesis. There was a strong positive correlationbetween the abundance of total and pyrite S along the profiles.The presence of pyrite S at VM (526 ± 60 ppm) suggestedthat even at VM bacterial sulfate reduction occurred. Ananaerobic incubation of JH peat indicated sulfate reductionrate of 600 nmol g^-1 day^-1. The turnover times forinorganic S pools were shorter than for the organic S pools.Cumulative S contents in the Czech peat bogs were found to besignificantly lower than in similar sites in the NortheasternU.S., even though the atmospheric S inputs were more thanthree times higher at the Czech sites. Possible causes of suchdiscrepancy are discussed.     

Methodology for quantification of waste generated in Spanish railway construction works

In the last years, the European Union (EU) has been focused on the reduction of construction and demolition (C&D) waste. Specifically, in 2006, Spain generated roughly 47million tons of C&D waste, of which only 13.6% was recycled. This situation has lead to the drawing up of many regulations on C&D waste during the past years forcing EU countries to include new measures for waste prevention and recycling. Among these measures, the mandatory obligation to quantify the C&D waste expected to be originated during a construction project is mandated. However, limited data is available on civil engineering projects. Therefore, the aim of this research study is to improve C&D waste management in railway projects, by developing a model for C&D waste quantification. For this purpose, we develop two equations which estimate in advance the amount, both in weight and volume, of the C&D waste likely to be generated in railway construction projects, including the category of C&D waste generated for the entire project.     

Correlation analysis between sulphate content and leaching of sulphates in recycled aggregates from construction and demolition wastes

In some recycled aggregates applications, such as component of new concrete or roads, the total content of soluble sulphates should be measured and controlled. Restrictions are usually motivated by the resistance or stability of the new structure, and in most cases, structural concerns can be remedied by the use of techniques such as sulphur-resistant cements. However, environmental risk assessment from recycling and reuse construction products is often forgotten. The purpose of this study is to analyse the content of soluble sulphate on eleven recycled aggregates and six samples prepared in laboratory by the addition of different gypsum percentages. As points of reference, two natural aggregates were tested. An analysis of the content of the leachable amount of heavy metals regulated by European regulation was included. As a result, the correlation between solubility and leachability data allow suggest a limiting gypsum amount of 4.4% on recycled aggregates. This limit satisfies EU Landfill Directive criteria, which is currently used as reference by public Spanish Government for recycled aggregates in construction works.     

Effect of aeration rate and moisture content on the emissions of selected VOCs during municipal solid waste composting

The influence of the industrial control composting conditions (aeration 0.005–0.300?L_air?kg^?1 and moisture 40–70?%) of municipal solid waste on the composition of the selected compound emitted (limonene, β-pinene, 2-butanone, undecane, phenol, toluene, dimethyl sulfide, dimethyl disulfide) was studied. The highest emissions of volatile organic compounds (VOCs) were observed in the early stages of the processes. At the end of the process, low concentrations of the emitted compounds were found. Aeration rate had a strong effect on emissions. High aeration rate (0.300?L_air?kg^?1?min^?1) caused normally high emissions of all selected compounds whereas low aeration rates (0.05?L_air?kg^?1?min^?1) could cause anaerobiosis problems and generation of organic sulphur compounds. We observed that the effect of the moisture upon the emitted concentrations varied depending on the studied compound.     

Physical Properties, Photo- and Bio-degradation of Baked Foams Based on Cassava Starch, Sugarcane Bagasse Fibers and Montmorillonite

The objectives of this work were to develop biodegradable trays from cassava starch, sugarcane fibers and Na-montmorillonite (Na-MMT) using a baking process and to study the effects of these components on the physical properties, photo- and bio-degradation of the trays. The sample F20 (produced with 20 g fiber/100 g formulation) showed the maximum yield production (100 %). All formulations resulted in well-shaped trays with densities between 0.1941 and 0.2966 g/cm³. The addition of fibers and Na-MMT resulted in less dense and less rigid trays compared to control samples (only starch). The studied processing conditions resulted in good nanoclay dispersion, leading to the formation of an exfoliated structure. The evaluation of the photo-degradation stability of the trays under UV exposure for 336 h showed that a sample produced with a specific combination of fiber and nanoclay (20 g fiber and 5 g nanoclay/100 g formulation) had the highest loss in stress at break (91 %). Biodegradation assays showed that Control trays (starch) and F20 (20 g fiber/100 g formulation) lost a greater percentage of their weight after 90 days of incubation in soil, with losses of up to 85.50 and 82.70 %, respectively.     

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.     

Valorisation of used cooking oil sludge by codigestion with swine manure

The addition of lipid wastes to the digestion of swine manure was studied as a means of increasing biogas production. Lipid waste was obtained from a biodiesel plant where used cooking oil is the feedstock. Digestion of this co-substrate was proposed as a way of valorising residual streams from the process of biodiesel production and to integrate the digestion process into the biorefinery concept.Batch digestion tests were performed at different co-digesting proportions obtaining as a result an increase in biogas production with the increase in the amount of co-substrate added to the mixture. Semi-continuous digestion was studied at a 7% (w/w) mass fraction of total solids. Co-digestion was successful at a hydraulic retention time (HRT) of 50 d but a decrease to 30 d resulted in a decrease in specific gas production and accumulation of volatile and long chain fatty acids. The CH₄ yield obtained was 326 ± 46 l/kg VS_feed at an HRT of 50 d, while this value was reduced to 274 ± 43 l/kg VS_feed when evaluated at an HRT of 30 d. However these values were higher than the one obtained under batch conditions (266 ± 40 l/kg VS_feed), thus indicating the need of acclimation to the co-substrate. Despite of operating at low organic loading rate (OLR), measurements from respirometry assays of digestate samples (at an HRT of 50 d) suggested that the effluent could not be directly applied to the soil as fertiliser and might have a negative effect over soil or crops.