Comparison of Predicted and Measured Concentrations for 58 Alternative models of Plume Transport in Complex Terrain

The purpose of this study was to evaluate alternative prediction models for the SO₂ concentrations produced in the vicinity of the Ohio Edison Company Sammis Power Plant. The plant is situated in the northeastern portion of the Ohio River Valley in complex terrain. Comparisons of the 16 highest predicted and measured short-term SO₂ concentrations were conducted for a one year period for 58 alternative models. Several models were found to predict reasonably accurately the 16 highest measured 24-hour SO₂ concentrations. Each of these models requires an upward adjustment in the plume centerline location as the plume is transported downwind in rising terrain. These same models overpredict by substantial margins the 16 highest measured 3-hour SO₂ concentrations. Improvements in emissions inventory data and improvements in the prediction models used are believed necessary to increase prediction accuracy further.     

Application of a combined measurement and modeling method to quantify windblown dust emissions from the exposed playa at Mono Lake, California

Particulate matter < or =10 microm (PM10) emissions due to wind erosion can vary dramatically with changing surface conditions. Crust formation, mechanical disturbance, soil texture, moisture, and chemical content of the soil can affect the amount of dust emitted during a wind event. A refined method of quantifying windblown dust emissions was applied at Mono Lake, CA, to account for changing surface conditions. This method used a combination of real-time sand flux monitoring, ambient PM10 monitoring, and dispersion modeling to estimate dust emissions and their downwind impact. The method identified periods with high emissions and periods when the surface was stable (no sand flux), even though winds may have been high. A network of 25 Cox sand catchers (CSCs) was used to measure the mass of saltating particles to estimate sand flux rates across a 2-km2 area. Two electronic sensors (Sensits) were used to time-resolve the CSC sand mass to estimate hourly sand flux rates, and a perimeter tapered element oscillating microbalance (TEOM) monitor measured hourly PM10 concentrations. Hourly sand flux rates were related by dispersion modeling to hourly PM10 concentrations to back-calculate the ratio of vertical PM10 flux to horizontal sand flux (K-factors). Geometric mean K-factor values (K(f)) were found to change seasonally, ranging from 1.3 x 10(-5) to 5.1 x 10(-5) for sand flux measured at 15 cm above the surface (q15). Hourly PM10 emissions, F, were calculated by applying seasonal K-factors to sand flux measurements (F = K(f) x q15). The maximum hourly PM10 emission rate from the study area was 76 g/m2 x hr (10-m wind speed = 23.5 m/sec). Maximum daily PM10 emissions were estimated at 450 g/m2 x day, and annual emissions at 1095 g/m2 x yr. Hourly PM10 emissions were used by the U.S. Environmental Protection Agency (EPA) guideline AERMOD dispersion model to estimate downwind ambient impacts. Model predictions compared well with monitor concentrations, with hourly PM10 ranging from 16 to over 60,000 microg/m3 (slope = 0.89, R2 = 0.77).     

CONTRIBUTION OF PRECIPITATION TO QUALITY OF URBAN STORM RUNOFF1

Precipitation and runoff samples were collected for 13 storms in a nonindustrial urban area in Central Pennsylvania between July 1980 and June 1981. Runoff was collected from tree surfaces, a residential roof and street, a shopping mall parking lot, a downtown business district alley, and a heavily traveled street. Analysis of the water samples showed 10 to 25 percent of the nitrogen, 25 percent of the sulfate, and less than 5 percent of the phosphorus, potassium, and calcium in water below a tree was deposited by the precipitation. The residential roof caused insignificant changes in water chemistry. The results for the four paved areas showed that all the nitrogen, and from 16 to 40 percent of the sulfate and 13, 4, and 2 percent of the phosphorus, potassium, and calcium, respectively, in runoff was deposited by the precipitation. Precipitation can also be an important source of sulfate and phosphorus in runoff. All of the surfaces raised the pH of the runoff, with the largest increases, from a pH of 4 to about 7, occurring in runoff from the paved areas. Precipitation and runoff chemistry was not related to antecedent conditions such as the length of the preceding dry period.     

Applying tqm to environmental site assessments under the astm standard

Total Quality Management was initially developed to facilitate an ethos of continuous improvement of the production process. It entails both an internal and external focus. The former depends on a cooperative effort among employees at all levels of the organization to analyze work processes, minimize process variance, and thereby maximize productivity. The latter requires close collaboration with suppliers to ensure that raw or processed materials can be readily and efficiently integrated into the production process and constant communication with the end user—the customer—to ensure that the process generates the expected level of quality. Applying TQM to service industry processes is a bit more complex. In addition to having to tailor the TQM approach to the specific service industry, the processes are seldom identical and tend not to lend themselves to the same type of statistical variance analysis that is considered a hallmark of TQM. Nevertheless, numerous case studies have shown that TQM is applicable to the service industry and can help to generate a culture of continuous improvement and enhance customer satisfaction. Environmental site assessments provide a unique challenge to proponents of TQM. Construction, geological, and hydrological characteristics are unique at each site; regulatory requirements differ by jurisdiction; access to historical information is inconsistent; auditors have varying backgrounds; and client needs and expectations differ. Nevertheless, as the American Society for Testing and Materials (ASTM) standard practice gains acceptance as a benchmark for environmental site assessments, the application of TQM practices to this service process becomes more practicable.     

The ecological relevance of current approaches for environmental protection from exposure to ionising radiation

This paper discusses the current approaches to environmental protection from ionising radiation from an ecological perspective, highlighting the need to understand fully what we are trying to protect. Ecologically relevant endpoints for environmental protection are discussed along with the need to integrate protection from ionising radiation with the approaches adopted for non-radioactive contaminants. A possible integrated assessment approach is outlined.