Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.     

State estimation in wastewater engineering: Application to an anaerobic process

The use of an extended Kalman filter for state estimation in biological wastewater treatment processes is discussed. The application of the technique requires an adequate mechanistic dynamic model and the identification and modelling of the major sources of stochastic disturbances in the process. The filter allows the on-line tracking of process variables which are not directly measurable. The use of an extended Kalman filter is illustrated through a simulated application to a high rate anaerobic wastewater treatment process.     

Application of cryofocusing hydride generation and atomic fluorescence detection for dissolved mercury species determination in natural water samples

The concentration levels of mercury (Hg) species in natural water samples are usually low. Consequently, accurate analysis with low detection limits is still a major problem. In this work, a method was applied for the simultaneous direct determination of dissolved mercury species in water samples by on-line hydride generation (HG), cryogenic trapping (CT), gas chromatography (GC) and detection by atomic fluorescence spectrometry (AFS). The suitability of the method for real samples with different organic matter and chloride contents was evaluated by recovery experiments in synthetic and natural spiked water samples. The HG method was compared with other current available methods for mercury analysis with respect to the different fraction of mercury analysed, i.e. 'reactive', 'reducible' or total. HG derivatization and SnCl2 reduction (with and without previous oxidation with BrCl) were applied to synthetic and natural (spiked and non-spiked) water samples. The influence of chloride and dissolved organic matter concentrations was studied. The results suggest that the HG procedure is suitable for the simultaneous determination of Hg2+ and MeHg+ in surface water samples. Inorganic mercury analysed by HG (i.e. reducible) is close to the total inorganic mercury.     

Mobilization of aluminium and deposition on fish gills during sea salt episodes--catchment liming as countermeasure

Episodic events may be critical with respect to aluminium (Al) toxicity in moderately acidified salmon rivers. The present work demonstrates that sea salt episodes enhance the toxicity of Al in acidic rivers. The documented sea salt episode (300 [micro sign]M Cl) mobilized positively charged Al species (0.4 to 1.1 [micro sign]M Al(i)), enhanced the Al accumulation on fish gills (0.9 to 10 [micro sign]mol g(-1) dw) and caused increased stress responses (6 to15 mM blood glucose) in fish. Accumulated Al on gills remained high several days after the episode. The presented results are based on a six-week field study in two tributary rivers on the west coast of Norway. Changes in the river water qualities and Al speciation were followed using in situ fractionation techniques. Al accumulation on gills and stress responses were followed for Atlantic salmon (Salmo salar) kept in tanks continually exposed to the changing water quality. The potential mobilization of Al from the two catchments was studied by extracting soils with diluted seawater (salinity of 3). To counteract Al toxicity, one of the tributary catchments has been limed. The potential mobility of Al by sea salt was lower in limed soils compared to acid soils, and the Al deposition on fish gills (<3.5 [micro sign]mol g(-1) dw) and associated stress responses stayed low during the sea salt episode in the river draining the limed catchment. Thus, for acid river systems in coastal areas, catchment liming should be considered as a useful countermeasure for Al toxicity.     

Suggested protocol for collecting, handling and preparing peat cores and peat samples for physical, chemical, mineralogical and isotopic analyses

For detailed reconstructions of atmospheric metal deposition using peat cores from bogs, a comprehensive protocol for working with peat cores is proposed. The first step is to locate and determine suitable sampling sites in accordance with the principal goal of the study, the period of time of interest and the precision required. Using the state of the art procedures and field equipment, peat cores are collected in such a way as to provide high quality records for paleoenvironmental study. Pertinent field observations gathered during the fieldwork are recorded in a field report. Cores are kept frozen at -18 degree C until they can be prepared in the laboratory. Frozen peat cores are precisely cut into 1 cm slices using a stainless steel band saw with stainless steel blades. The outside edges of each slice are removed using a titanium knife to avoid any possible contamination which might have occurred during the sampling and handling stage. Each slice is split, with one-half kept frozen for future studies (archived), and the other half further subdivided for physical, chemical, and mineralogical analyses. Physical parameters such as ash and water contents, the bulk density and the degree of decomposition of the peat are determined using established methods. A subsample is dried overnight at 105 degree C in a drying oven and milled in a centrifugal mill with titanium sieve. Prior to any expensive and time consuming chemical procedures and analyses, the resulting powdered samples, after manual homogenisation, are measured for more than twenty-two major and trace elements using non-destructive X-Ray fluorescence (XRF) methods. This approach provides lots of valuable geochemical data which documents the natural geochemical processes which occur in the peat profiles and their possible effect on the trace metal profiles. The development, evaluation and use of peat cores from bogs as archives of high-resolution records of atmospheric deposition of mineral dust and trace elements have led to the development of many analytical procedures which now permit the measurement of a wide range of elements in peat samples such as lead and lead isotope ratios, mercury, arsenic, antimony, silver, molybdenum, thorium, uranium, rare earth elements. Radiometric methods (the carbon bomb pulse of (14)C, (210)Pb and conventional (14)C dating) are combined to allow reliable age-depth models to be reconstructed for each peat profile.     

One-year monitoring survey of organic compounds (PAHs, PCBs, TBT), heavy metals and biomarkers in blue mussels from the Arcachon Bay, France

Marine mussels Mytilus sp. were transplanted on a monthly basis in cages over one year to oyster farms and harbours in the Arcachon Bay (France) in order to assess the water quality of the bay. Contaminant levels (organotin compounds, trace metals, PCBs and PAHs) were measured in tissues of transplanted mussels and mussels from a reference station, along with physiological parameters of the mussels (condition indexes, lipid content and dry weight). Four biomarkers (AChE: acetylcholinesterase activity, GST: gluthathione S-transferase activity, CAT: catalase activity and TBARS: thiobarbituric acid-reactive substance content) were also monitored. The remote stations monitored (oyster parks) exhibited no accumulation pattern of pollutants. Their respective concentrations therefore constitute a background level of the contamination in the bay ([TBT]= 30 ng Sn g(-1) dw, [SigmaHAPs]= 100 ng g(-1) dw, [SigmaPCBs]= 35 ng g(-1) dw). The elevated chemical contamination of the largest harbour of the bay, the Arcachon harbour, can be interpreted in terms of persistence of organotin compounds ([SigmaOTs]= 1500-2000 ng Sn g(-1) dw) and PAHs ([SigmaHAPs]= 4500-5000 ng g(-1) dw) in sediments and, to a lesser extent, of direct inputs of copper ([Cu]= 20 microg g(-1) dw in harbours versus 7 in oyster parks) and petrogenic PAHs ([methylphenanthrenes]= 1600 ng g(-1) dw in the dockyard versus 170 at the gas stations), related to the use of copper-based antifouling paints and to dockyard activity, respectively. However, the Arcachon Bay presents a low contamination level by PCBs and metals, including harbour stations. Furthermore, higher levels of other PAHs (particularly alkyl PAHs such as methylphenanthrenes/1600 ng g(-1) dw) not included in the 16 PAHs from the EPA priority list (usually studied in biomonitoring programmes/1500 ng g(-1) dw) in the Arcachon harbour underline the need to integrate these compounds in biomonitoring of highly PAH-polluted areas such as harbours in order to avoid misinterpretation of the biological responses observed. Biomarker responses were not able to discriminate the different chemical contamination levels recorded in the Arcachon Bay and rather reflected changes in environmental factors. Furthermore, the strong intraspecies variability of biological responses could be due to genetic differences of mussels from the Arcachon Bay. It is the first time that such an integrated monitoring is performed in the Arcachon Bay, also taking into account seasonal variations of chemical contents and biomarkers levels in mussel tissues.     

Environmental benchmarks vs. ecological benchmarks for assessment and monitoring in Canada: Is there a difference?

Environmental benchmarks are widely used in Canadian environmental assessment as a standard against which to monitor air or water quality in response to human activities in the environment. Recent work in Canada has developed the concept of ecological benchmarks as a complement to environmental benchmarks. However, implementation of ecological benchmarks may be challenging. This paper presents an analogy between ecological benchmarks and the more commonly used environmental benchmarks, as an attempt to increase understanding and use of ecological benchmarks in resource management, assessment, and monitoring. Ecological benchmarks, and their corresponding indicators, will be challenging to identify and use. However, through the use of the principles of adaptive management, effective ecological indicators and benchmarks can be established. Although it is essential that ecological benchmarks are site-specific, the analogy and general principles outlined here are applicable to assessment and monitoring in any part of the world.