A novel application of concentrated solar thermal energy in foundries

Scrap preheating in foundries is a technology that saves melting energy, leading to economic and environmental benefits. The proposed method in this paper utilizes solar thermal energy for preheating scrap, effected through a parabolic trough concentrator that focuses sunlight onto a receiver which carries the metallic scrap. Scraps of various thicknesses were placed on the receiver to study the heat absorption by them. Experimental results revealed the pattern with which heat is gained by the scrap, the efficiency of the process and how it is affected as the scrap gains heat. The inferences from them gave practical guidelines on handling scraps for best possible energy savings. Based on the experiments conducted, preheat of up to 160 °C and a maximum efficiency of 70 % and a minimum efficiency of 40 % could be achieved across the time elapsed and heat gained by the scrap. Calculations show that this technology has the potential to save around 8 % of the energy consumption in foundries. Cumulative benefits are very encouraging: 180.45 million kWh of energy savings and 203,905 t of carbon emissions cut per year across the globe. This research reveals immense scope for this technology to be adopted by foundries throughout the world.     

Preparation of gasification feedstock from leafy biomass

Dried leaves are a potential source of energy although these are not commonly used beside to satisfy daily energy demands in rural areas. This paper aims at preparing a leafy biomass feedstock in the form of briquettes which can be directly used for combustion or to extract the combustible gas using a gasifier. Teak (Tectona grandis) and rubber (Hevea brasiliensis) leaves are considered for the present study. A binder-assisted briquetting technique with tapioca starch as binder is adopted. Properties of these leafy biomass briquettes such as moisture content, calorific value, compressive strength, and shatter index are determined. From the study, briquettes with biomass-to-binder ratio of 3:5 are found to be stable. Higher mass percentage of binder is considered for preparation of briquettes due to the fact that leafy biomasses do not adhere well on densification with lower binder content. Ultimate analysis test is conducted to analyze the gasification potential of the briquettes. Results show that the leafy biomass prepared from teak and rubber leaves has calorific values of 17.5 and 17.8 MJ/kg, respectively, which are comparable with those of existing biomass feedstock made of sawdust, rice husk, and rice straw.     

Constructed wetlands may lower inorganic nutrient inputs but enhance DOC loadings into a drinking water reservoir in North Wales

Environmental Science and Pollution Research - The objective of this study was to monitor a newly constructed wetland (CW) in north Wales, UK, to assess whether it contributes to an improvement in...     

The ecology of the red fox (<Emphasis Type="Italic">Vulpes vulpes</Emphasis> L.) in the middle Lena River basin

The population of foxes in the central regions of Yakutia has grown by a factor of four to five during the period from 2000 to 2011–2012, following an increase in the abundance of voles from the genus Microtus. A total of 130 carcasses of foxes taken in 2007–2012 have been examined. Age- and sex-related variation in morphological features has been described. The demographic structure of the population has been studied by estimating animal age from annual layers in the recording structures. Changes in female fertility and involvement in reproduction depending on age and feeding conditions have been analyzed. Changes in the composition of fox diet caused by long-term population depression in the mountain hare and their effect on the dynamics of fox abundance have been revealed. Age- and sex-related characteristics of the condition factor in foxes and sex-related differences in their dietary preferences have been demonstrated.     

Spatial and temporal organization of benthic macroinvertebrate communities in Lake Chany,Western Siberia

Communities of benthic macroinvertebrates in drainless Lake Chany, the largest lake in Western Siberia, have been analyzed to estimate the effects of basic abiotic ecological factors (hydrophysical and hydrochemical parameters of water and the type of bottom ground) on their composition, structure, and dynamics. It has been shown that the level of development of these communities depends mainly on the water regime of the lake and also on the type of bottom ground, lake depth, and water mineral content.     

On ecotones as foci of ant species richness in a forest nature reserve (case study of the Voronezh Biosphere Reserve)

The role of ecotones with different (sharp or smooth) spatial boundaries between forest and meadow in ant biodiversity preservation was studied at the right-of-way of a power line in the Voronezh Reserve. The ecotone with a sharp boundary between forest and meadow (transitional zone 2 m wide) had higher species richness of ants compared to the ecotones (also 2 m wide) with smooth boundary between forest and meadow.     

Epigenetic variation in the American mink, <Emphasis Type="Italic">Neovison vison</Emphasis>, from eastern Europe: A search for factors of polymorphism

A comparative analysis of epigenetic variation has been performed in nine European populations and population groups of the American mink. It has been shown that differentiation of samples in nonmetric characters is due mainly to endogenous processes that have occurred in introduced populations in the course of colonization of new territory by the invasive species. Environmental factors have played a secondary role, with the influence of the geographic (latitudinal) origin of a given sample being considerable and stronger than that of macroclimatic factors.     

Two-echelon closed-loop supply chain deterministic inventory models in a batch production environment

This paper considers a two-echelon closed-loop supply chain consisting of a manufacturer and a remanufacturer at the upper echelon and a retailer at the lower echelon. The retailer faces a constant demand from customers, which is satisfied through recovered and new products received from the remanufacturer and the manufacturer, respectively. The manufacturer produces the product with finite rate, whereas the recovery of returned product is instantaneous at the remanufacturer. We develop three models to determine the optimal production-inventory policy of the players for minimizing the joint total cost of the system. In the first model, the retailer receives the product in batches from the manufacturer and the remanufacture simultaneously, whereas in the second and third models, the batches are received alternatively. In the third model, however, the procurement of raw material at the manufacturer is also considered. Numerical illustration is presented to examine the impact of certain key parameters.     

Economic and environmental value stream map (E2VSM) simulation for multi-product manufacturing systems

Value stream mapping (VSM) is a well-accepted tool within lean manufacturing concept which is often used for analysing and designing the flow of materials and information required to manufacture a product. However, the analysis is static and single product oriented, which fails to cope with either the variation of production plan or a multi-product environment. In addition, the environmental impact of a manufacturing system is highly associated with the dynamic consumption of energy and resources. Despite the recent integration of VSM with simulation or environmental studies (in the domain of energy efficiency), still neglected is the dynamic assessment of all the resources involved in a multi-product production environment. This paper presents a methodology for modelling multi-product manufacturing systems with dynamic material, energy and information flows with the aim to generate economic and environmental value stream maps (E²VSM). The proposed methodology is validated with an industrial case.