The effect of diesel fuel sulfur content on particulate matter emissions for a nonroad diesel generator

The effect of sulfur content on diesel particulate matter (DPM) emissions was studied using a diesel generator (Generac Model SD080, rated at 80 kW) as the emission source to simulate nonroad diesel emissions. A load simulator was used to apply loads to the generator at 0, 25, 50, and 75 kW, respectively. Three diesel fuels containing 500, 2100, and 3700 ppm sulfur by weight were selected as generator fuels. The U.S. Environmental Protection Agency sampling Method 5 "Determination of Particulate Matter Emissions from Stationary Sources" together with Method 1A "Sample and Velocity Traverses for Stationary Sources with Small Stacks or Ducts" was adopted as a reference method for measurement of the exhaust gas flow rate and DPM mass concentration. The effects of various parameters on DPM concentration have been studied, such as fuel sulfur contents, engine loads, and fuel usage rates. The increase of average DPM concentrations from 3.9 mg/Nm3 (n cubic meter) at 0 kW to 36.8 mg/Nm3 at 75 kW is strongly correlated with the increase of applied loads and sulfur content in the diesel fuel, whereas the fuel consumption rates are only a function of applied loads. An empirical correlation for estimating DPM concentration is obtained when fuel sulfur content and engine loads are known for these types of generators: Y = Zm(alphaX + beta), where Y is the DPM concentration, mg/m3, Z is the fuel sulfur content, ppm(w) (limited to 500-3700 ppm(w)), X is the applied load, kW, m is the constant, 0.407, alpha and beta are the numerical coefficients, 0.0118 +/- 0.0028 (95% confidence interval) and 0.4535 +/- 0.1288 (95% confidence interval), respectively.     

Investigation on the influence of methanol on adsorption and leaching of pesticides with soil column liquid chromatography

The effect of methanol of low concentration on adsorption and leaching of atrazine and tebuconazole was studied in this paper. The adsorption coefficients and the retardation factors (R^m) of pesticides on EUROSOIL 3# log-linearly decreased as volumetric fraction of methanol (f^c) was increased in the binary solvent mixtures of methanol and water. These data are consistent with solvophobic theory formerly outlined for describing the adsorption and transport of hydrophobic organic chemicals from mixed solvents. Nevertheless, the adsorption of these pesticides in soil–water system slightly increased when the soil was pre-washed with methanol in comparison with that pre-washed with water (pure water system). Furthermore, their adsorption coefficients were still higher in binary solvent systems with methanol of very low concentrations, i.e. f^c<0.03 for atrazine and f^c<0.01 for tebuconazole, than those in pure water system. The adsorption coefficients (logK^w) of atrazine and tebuconazole predicted by solvophobic theory were 0.5792 and 1.6525, respectively, and their experimental logK^w were 0.3701 and 1.6275 in pure water system. Obviously, the predicted logK^w of the two pesticides was higher than the experimental log K^w in pure water system. The predicted K^w and the retardation factor (R^w) in pure water system by solvophobic theory are thus possibly inaccurate.     

利用分子信标和EXO III放大荧光信号快速检测Ag+

设计新型的DNA探针,其主要功能区域包含适配体区域和分子信标互补区域;当无靶标存在时,羧基荧光素（FAM）的荧光被黑洞猝灭基团（BHQ）猝灭,加入靶标后,Ag⁺与适配体区域特异性结合,使得分子信标与其互补区域发生结合,加入EXO Ⅲ后,分子信标被酶解,从而释放Ag⁺/DNA探针复合物用于下一轮反应,同时产生大量的FAM,因此,可以通过荧光的增强来定量检测靶标的含量.评价了该方法的灵敏度和选择性,探究它在实际样品中的表现能力.结果表明,适配体区域与分子信标间隔2个碱基的DNA探针与分子信标结合效果最好,检测的信噪比最大.该方法对Ag⁺的检测最低下限（LOD）为0.1nmol/L,在0.5~200nmol/L范围内,荧光值与靶标浓度成线性关系（R²=0.994）.对实际样品的检测在20~200nmol/L范围内呈线性关系（R²=0.998）,且能很好的从混合样品中区分10nmol/L Ag⁺.该研究建立的快速检测Ag⁺方法具有良好的线性定量能力和操作性能,且灵敏度高、特异性强,可满足现实的需求.     

成都冬季一次持续污染过程气象成因及气溶胶垂直结构和演变特征

基于气溶胶激光雷达观测和环境监测站污染物浓度数据、气象观测资料及HYSPLIT后向轨迹模式,分析了2017年12月中下旬,成都市一次本地积累和沙尘输送影响的持续污染过程中污染物浓度、污染物来源、天气系统和气溶胶消光系数的垂直分布及演变.结果表明:①此次污染过程持续时间长,根据气象条件和主要污染物种类,分为本地污染累积、北方沙尘输送和混合影响3个阶段.②本地污染积累阶段,消光系数垂直分布不均匀,受湿度、太阳辐照与逆温层等气象因子的影响,垂直结构变化较大.消光系数最大值多出现在250 m附近,此阶段退偏比数值很小.③沙尘影响阶段,消光系数较前期明显下降,高值区位于250 m及2 km处.退偏比显示沙尘粒子于29日午后开始逐渐抵达成都市2 km高空,并于夜间达到峰值.退偏比相较本地污染累积阶段明显增大,各时段退偏比结构类似,近地面数值略低于高空.④混合影响阶段,消光系数强度小幅回升,退偏比显示有部分沙尘粒子漂浮在1～2 km高度上.     

高效除磷渗滤床填料筛选及连续流动态运行特性

磷是造成水体富营养化的重要因素之一,深度去除污染水体中的磷,具有重要的环保意义.为此,本研究比较了多种填料包括海绵铁及其改性填料、钢渣、活性氧化铝、活性炭的吸附除磷特性及动力学,探究了除磷机理,构建了高效除磷渗滤床,考察了动态连续流运行条件下的除磷特性.结果表明酸改性海绵铁具有最高的饱和磷吸附容量,为19.45 mg·g^-1,碱改性海绵铁、活性氧化铝、钢渣、未改性海绵铁及活性炭的饱和磷吸附容量分别为10.91、8.70、7.73、3.39和1.34 mg·g^-1.在此基础上,利用高效除磷填料酸改性海绵铁和钢渣构建了除磷渗滤床,开展了连续240 d的连续流实验,在磷容积负荷为6 g·d^-1·m^-3条件下,渗滤床累积磷吸附量达到10215 mg,单位容积吸附量达到1.62 kg·m^-3.总之,利用酸改性海绵铁和钢渣构建的除磷渗滤床具有较高的除磷效率和性能,可以作为除磷单元与现有的水污染治理及净化工艺耦合,提高或拓展系统除磷功能.     

成都西南城郊黑碳和PM2.5 浓度变化特征及其影响因子

四川盆地是我国灰霾和大气污染易发和频发区之一,目前关于本地区黑碳气溶胶（black carbon,BC）的相关研究较少。利用2017年11月—2018年12月成都西南城郊地区黑碳气溶胶以及PM_2.5观测资料,结合气象资料和其他污染物浓度资料,分析BC和PM_2.5浓度,BC浓度在PM_2.5浓度中所占比例（黑碳占比）的季节、月、日变化特征及其影响因子。结果表明：（1）BC逐小时浓度范围为0.18—40.51 μg?m^?3,平均值为(5.26±4.68) μg?m^?3,本底浓度为3.34 μg?m^?3。PM_2.5逐小时浓度范围为1.00—344.50 μg?m^?3,平均值为(60.02±46.91) μg?m^?3,本底浓度为33.38 μg?m^?3。日变化均呈“白天低,早晨、夜间高”的变化特征,其中冬季浓度最高,春、秋季次之,夏季浓度最低。（2）黑碳占比均值为9.16%±5.13%,白天黑碳占比低,夜间黑碳占比高,且夏季最高,冬季最低。随着空气污染加重,冬季占比缓慢增加,其他三季占比减小。（3）BC与NO₂和CO相关性较好,表明西南城郊BC排放主要受机动车尾气、生物质燃烧影响。BC和SO₂相关系数偏小,燃煤等工业源排放对西南城郊BC的贡献较小。（4）风速、温度和湿度与BC浓度均有很好的相关性,其中风速对BC浓度的影响最大,当风速小于2.0 m?s^?1时,BC浓度值明显偏高;BC浓度大于20.00 μg?m^?3的高值区主要集中在西北、西南以及东北风向上,即：偏东北方向市中心大气中的污染物,以及西南方向远郊地区的污染物可能对西南城郊高浓度黑碳的贡献更大。     

UV-B辐射增强对芦苇生长及生理特性的影响

在UV-B辐射增强条件下,以芦苇为材料,研究了不同辐射梯度对芦苇生长及生理特性的影响.结果表明:与自然光照相比,UV-B辐射增强可显著降低芦苇植株高度、比叶面积、生物量,且高强度辐射处理的影响大于低强度辐射,随辐射时间延长,生物量分配有向地下部分转移的趋势;与自然光照相比,UV-B辐射增强可显著增加芦苇叶片丙二醛(MDA)含量、抗氧化酶活性(SOD、CAT、GR、APX)、抗氧化物质含量(GSH、As A),且随辐射强度增大,MDA含量、酶活性、抗氧化物质含量增强程度加剧,但随辐射时间延长,高辐射处理下,GR酶活显著低于对照,GSH也表现出相应的趋势;UV-B辐射增强条件下,类胡萝卜素含量显著降低,而类黄酮含量较对照组却显著升高,且高强度辐射处理对芦苇叶片紫外吸收物质的影响大于低强度辐射.     

相变储能光伏太阳能热泵干燥系统的研究

建立了相变储能光伏太阳能热泵干燥系统实验平台,介绍了系统的运行方式以及太阳能光伏集热蒸发器与直流压缩机的匹配计算,最后对实验数据进行了分析。结果表明,太阳能辐照量为800 W/m~2、光伏集热蒸发器面积为12 m~2的条件下,系统制热功率为10 k W,太阳能光伏集热蒸发器发电量为6.2 k W·h,大于直流压缩机的耗电量,满足供电要求;实验所得系统COP为3.25。相变储能可以解决太阳辐照波动导致的系统运行不稳定问题,具有显著的节能性和环保性。     

粒径和温度对玉米秸秆生物碳吸附锶的耦合影响

以玉米秸秆为原材料,在350℃下采用限氧裂解法制备了4种粒径的生物碳(BC-9.31、BC-20.26、BC-71.07、BC-101.90,数字代表样品的中值径,单位μm),对比研究了15℃、25℃、35℃、45℃下生物碳对锶的吸附行为,旨在阐明生物碳粒径和溶液温度对生物碳吸附锶的耦合影响。结果表明:生物碳粒径和溶液温度对等温吸附曲线的基本特征影响较小,Freundlich模型能较好地拟合吸附过程(R2=0.915~0.997,N=0.513~0.745);生物碳吸附锶是以熵驱动为主的物理吸附过程,熵变ΔS为75.66~99.43 J/(mol·K),焓变ΔH为18.18~25.84 k J/mol;生物碳对锶的吸附性能大体与溶液温度呈正相关,与颗粒粒径呈负相关,同时颗粒粒径与溶液温度存在耦合影响;生物碳粒径越小,锶吸附过程受温度影响越小;温度越高,锶吸附受粒径影响越小。     

溶菌酶和硫酸铝联用优化污泥脱水性能的研究

以污泥沉降体积、污泥比阻和污泥泥饼含水率为指标,考察了溶菌酶和硫酸铝联用时加药方式和加药剂量对活性污泥沉降性能及脱水性能的影响。结果表明,先投加溶菌酶后投加硫酸铝时污泥的脱水性能更佳,硫酸铝和溶菌酶的最佳投加量均为0.10 g/g TS(总固体),此时,污泥泥饼含水率和污泥比阻分别可达71.84%和0.68×1012m/kg,相比于硫酸铝单独调理分别降低了约5%和0.23×1012m/kg。污泥胞外聚合物(EPS)含量分析表明,溶菌酶和硫酸铝联用时显著降低了污泥中LB-EPS(松散附着性EPS)含量,在最佳投量下可将原污泥的LB-EPS中的蛋白质和多糖依次从(13.44±2.11)mg/L和(23.97±3.44)mg/L降至(1.72±0.32)mg/L和(8.69±0.15)mg/L,表明联合处理使得EPS中的水分得到释放,提高了脱水性能。