The value of Seasonal Correction Factors in assessing the health risk from domestic radon: a case study in Northamptonshire, UK

Following an intensive survey of domestic radon levels in the United Kingdom (UK), the former National Radiological Protection Board (NRPB), now the Radiation Protection Division of the Health Protection Agency (HPA-RPD), established a measurement protocol and promulgated Seasonal Correction Factors applicable to the country as a whole. Radon levels in the domestic built environment are assumed to vary systematically and repeatably during the year, being generally higher in winter. The Seasonal Correction Factors therefore comprise a series of numerical multipliers, which convert a 1-month or 3-month radon concentration measurement, commencing in any month of the year, to an effective annual mean radon concentration. In a recent project undertaken to assess the utility of short-term exposures in quantifying domestic radon levels, a comparative assessment of a number of integrating detector types was undertaken, with radon levels in 34 houses on common geology monitored over a 12-month period using dose-integrating track-etch detectors exposed in pairs (one upstairs, one downstairs) at 1-month and 3-month resolution. Seasonal variability of radon concentrations departed significantly from that expected on the basis of the HPA-RPD Seasonal Correction Factor set, with year-end discontinuities at both 1-month and 3-month measurement resolutions. Following this study, monitoring with electrets was continued in four properties, with weekly radon concentration data now available for a total duration in excess of three and a half years. Analysis of this data has permitted the derivation of reliable local Seasonal Correction Factors. Overall, these are significantly lower than those recommended by HPA-RPD, but are comparable with other results from the UK and from abroad, particularly those that recognise geological diversity and are consequently prepared on a regional rather than a national basis. This finding calls into question the validity of using nationally aggregated Seasonal Correction Factors, especially for shorter exposures, and the universal applicability of these corrections is discussed in detail.     

Recycling potential of MWCNTs/HDPE nanocomposite filament: 3D printing and mechanical characterization

Journal of Material Cycles and Waste Management - Fused filament fabrication (FFF) based additive manufacturing (AM) process is a widely used and emerging manufacturing process for...     

Growth of Dehalococcoides spp. and increased abundance of reductive dehalogenase genes in anaerobic PCB-contaminated sediment microcosms

Polychlorinated biphenyls (PCBs) contaminate 19% of US Superfund sites and represent a serious risk to human and environmental health. One promising strategy to remediate PCB-contaminated sediments utilizes organohalide-respiring bacteria (OHRB) that dechlorinate PCBs.

However, functional genes that act as biomarkers for PCB dechlorination processes (i.e., reductive dehalogenase genes) are poorly understood. Here, we developed anaerobic sediment microcosms that harbor an OHRB community dominated by the genus Dehalococcoides. During the 430-day microcosm incubation, Dehalococcoides 16S rRNA sequences increased two orders of magnitude to 10⁷ copies/g of sediment, and at the same time, PCB118 decreased by as much as 70%. In addition, the OHRB community dechlorinated a range of penta- and tetra-chlorinated PCB congeners including PCBs 66, 70?+?74?+?76, 95, 90?+?101, and PCB110 without exogenous electron donor. We quantified candidate reductive dehalogenase (RDase) genes over a 430-day incubation period and found rd14, a reductive dehalogenase that belongs to Dehalococcoides mccartyi strain CG5, was enriched to 10⁷ copies/g of sediment. At the same time, pcbA5 was enriched to only 10⁵ copies/g of sediment. A survey for additional RDase genes revealed sequences similar to strain CG5’s rd4 and rd8. In addition to demonstrating the PCB dechlorination potential of native microbial communities in contaminated freshwater sediments, our results suggest candidate functional genes with previously unexplored potential could serve as biomarkers of PCB dechlorination processes.

     

Protective effects of thymoquinone against acrylamide-induced liver,kidney and brain oxidative damage in rats

Environmental Science and Pollution Research - Acrylamide (AA), an industrial monomer, may cause multi-organ toxicity through induction of oxidative stress and inflammation. The antioxidant...     

Biogeochemical consequences of a changing Arctic shelf seafloor ecosystem

Unprecedented and dramatic transformations are occurring in the Arctic in response to climate change, but academic, public, and political discourse has disproportionately focussed on the most visible and direct aspects of change, including sea ice melt, permafrost thaw, the fate of charismatic megafauna, and the expansion of fisheries. Such narratives disregard the importance of less visible and indirect processes and, in particular, miss the substantive contribution of the shelf seafloor in regulating nutrients and sequestering carbon. Here, we summarise the biogeochemical functioning of the Arctic shelf seafloor before considering how climate change and regional adjustments to human activities may alter its biogeochemical and ecological dynamics, including ecosystem function, carbon burial, or nutrient recycling. We highlight the importance of the Arctic benthic system in mitigating climatic and anthropogenic change and, with a focus on the Barents Sea, offer some observations and our perspectives on future management and policy.     

Pilot project of mechanical-biological treatment of waste in Brazil

By mechanical-biological treatment (MBT) of residual municipal solid waste the behaviour of landfills can be significantly improved. After MBT the organic content (COD and BOD5), total organic carbon, and total nitrogen in the leachate, as well as the gas production rate, are reduced to values lower than 90% of the fresh untreated waste. The volume of the stabilized material to be disposed on landfills decreases enormously, by up to 70%. The monitoring effort for a landfill constructed under these conditions is reduced to a minimum and the stabilized material can be used in other ways, as material for reforestation, for cover material or for thermal utilization to produce energy. Environmental conditions are important in MBT, as well as waste characteristics. This paper describes the results of a pilot project of MBT performed in Rio de Janeiro, Brazil. The results have shown that this technology can be used successfully in developing countries, with economy for the society and important results for the environment.     

Carbonization of waste PVC to develop porous carbon material without further activation

Efficient removal of chlorine from PVC achieved by two-stage heat-treatment (280 and 410 degrees C) provided chlorine-free isotropic pitch containing additive. The pitch was stabilized and carbonized into porous carbons with surface areas of approximately 300 m2/g. Resultant porous carbons showed three pore structures of supermicropore, micropore and mesopore. The generation of CO2 from the decomposition of the CaCO3 additive in waste PVC is responsible for the development of porous structures. The surface area of the carbonized product increased after the removal of CaO.     

Classification of in-flight catering wastes in Egypt air flights and its potential as energy source (chemical approach)

Waste to energy conversion is based on the classification of waste. In-flight catering wastes resulting from Egypt Airlines economy class passengers were classified. The solid waste stream generated contains plastic, paper, left-over waste food and aluminum. The type of meal served varies according to the period of flight and so the quantity and content of the waste stream. It was found that the waste generation rate varied from 61.3 to 265 g according to the meal type. Breakfast snack meal generates the highest weight of waste which recorded an average of 265 g. Plastic waste generated varied from 39.6% to 64.6% by weight for the various types of meals served. A total amount of 725 tons were generated annually from organic waste (paper, plastic and food waste) among which a non combustible 39.4 tons of aluminum. The calorific value for each generated item is calculated and the total energy potential reached up to 14.3 TJ annually.     

A GIS based transportation model for solid waste disposal--a case study on Asansol municipality

Uncontrolled growth of the urban population in developing countries in recent years has made solid waste management an important issue. Very often, a substantial amount of total expenditures is spent on the collection of solid waste by city authorities. Optimization of the routing system for collection and transport of solid waste thus constitutes an important component of an effective solid waste management system. This paper describes an attempt to design and develop an appropriate storage, collection and disposal plan for the Asansol Municipality Corporation (AMC) of West Bengal State (India). A GIS optimal routing model is proposed to determine the minimum cost/distance efficient collection paths for transporting the solid wastes to the landfill. The model uses information on population density, waste generation capacity, road network and the types of road, storage bins and collection vehicles, etc. The proposed model can be used as a decision support tool by municipal authorities for efficient management of the daily operations for transporting solid wastes, load balancing within vehicles, managing fuel consumption and generating work schedules for the workers and vehicles. The total cost of the proposed collection systems is estimated to be around 80 million rupees for the fixed cost of storage bins, collection vehicles and a sanitary landfill and around 8.4 million rupees for the annual operating cost of crews, vehicles and landfill maintenance. A substantial amount (25 million rupees/yr) is currently being spent by AMC on waste collection alone without any proper storage/collection system and sanitary landfill. Over a projected period of 15 yr, the overall savings is thus very significant.     

The effect of sodium chloride on the dissolution of calcium silicate hydrate gels

The use of cement based materials will be widespread in the long-term management of radioactive materials in the United Kingdom. One of the applications could be the Nirex reference vault backfill (NRVB) as an engineered barrier within a deep geological repository. NRVB confers alkaline conditions, which would provide a robust chemical barrier through the control of the solubility of some key radionuclides, enhanced sorption and minimised corrosion of steel containers. An understanding of the dissolution of C-S-H gels in cement under the appropriate conditions (e.g., saline groundwaters) is necessary to demonstrate the expected evolution of the chemistry over time and to provide sufficient cement to buffer the porewater conditions for the required time. A programme of experimental work has been undertaken to investigate C-S-H gel dissolution behaviour in sodium chloride solutions and the effect of calcium/silicon ratio (C/S), temperature and cation type on this behaviour. Reductions in calcium concentration and pH values were observed with samples equilibrated at 45 degrees C compared to those prepared at 25 degrees C. The effect of salt cation type on salt-concentration dependence of the dissolution of C-S-H gels was investigated by the addition of lithium or potassium chloride in place of sodium chloride for gels with a C/S of 1.0 and 1.8. With a C/S of 1.0, similar increases in dissolved calcium concentration with increasing ionic strength were recorded for the different salts. However, at a C/S of 1.8, anomalously high calcium concentrations were observed in the presence of lithium.