Microwave regeneration of activated carbon used for removal of solvents from vented air

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

Indoor and outdoor air quality investigation at schools in Hong Kong

Five classrooms in Hong Kong (HK), air-conditioned or ceiling fans ventilated, were chosen for investigation of indoor and outdoor air quality. Parameters such as temperature, relative humidity (RH), carbon dioxide (CO2), sulphur dioxide (SO2), nitric oxide (NO), nitrogen dioxide (NO2), respirable particulate matter (PM10), formaldehyde (HCHO), and total bacteria counts were monitored indoors and outdoors simultaneously. The average respirable particulate matter concentrations were higher than the HK Objective, and the maximum indoor PM10 level exceeded 1000 microg/m3. Indoor CO2 concentrations often exceeded 1000 microl/l in air-conditioning and ceiling fan classrooms, indicating inadequate ventilation. Maximum indoor CO2 level reached 5900 microl/l during class at the classroom with cooling tower ventilation. Increasing the rate of ventilation or implementation of breaks between classes is recommended to alleviate the high CO2 level. Other pollution parameters measured in this study complied with the standards. The two most important classroom air quality problems in Hong Kong were PM10 and CO2 levels.     

Study on the cytotoxicity of microcystin-LR on cultured cells

The toxicity of purified blue-green algal toxin, microcystin-LR, on permanent cell lines KB, NIH/3T3, H-4-II-E, HeLa, Vero, Hep G2, Caco-2 and HL-60 was studied. Assessment of cell viability using colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays indicated that purified microcystin-LR induced toxic effect on KB and H-4-II-E cell lines after 96 h incubation at toxin concentrations greater than 18.75 microg/ml. KB cell line was selected for further study when reproducibility, consistency and sensitivity were considered. Significant amounts of lactate dehydrogenase (LDH) were released from KB cells when incubation durations were 72 and 96 h with toxin concentrations of 18.75 microg/ml and higher. Although previous studies suggested that microcystin-LR had no cytotoxic effect on permanent cell lines, LDH release assay performed on KB cells indicated that exposure to microcystin-LR could result in damage to the cell membrane.     

Priority assessment of toxic substances in life cycle assessment. Part I: calculation of toxicity potentials for 181 substances with the nested multi-media fate, exposure and effects model USES-LCA

Toxicity potentials are standard values used in life cycle assessment (LCA) to enable a comparison of toxic impacts between substances. In most cases, toxicity potentials are calculated with multi-media fate models. Until now, unrealistic system settings were used for these calculations. The present paper outlines an improved model to calculate toxicity potentials: the global nested multi-media fate, exposure and effects model USES-LCA. It is based on the Uniform System for the Evaluation of Substances 2.0 (USES 2.0). USES-LCA was used to calculate for 181 substances toxicity potentials for the six impact categories freshwater aquatic ecotoxicity, marine aquatic ecotoxicity, freshwater sediment ecotoxicity, marine sediment ecotoxicity, terrestrial ecotoxicity and human toxicity, after initial emission to the compartments air, freshwater, seawater, industrial soil and agricultural soil, respectively. Differences of several orders of magnitude were found between the new toxicity potentials and those calculated previously.     

The influence on partial order ranking from input parameter uncertainty. Definition of a robustness parameter

The method of partial order ranking has been used within the environmental area for a variety of purposes as an attractive way of handling complex information. However, the environmental data are often associated with a significant degree of uncertainty. In this investigation the general nature of the influence from data uncertainty on the partial order ranking is analyzed. A Monte Carlo type analysis is performed in which a series of randomly formed data are used to test the influence of data uncertainty. The partial order ranking is interpreted, where the results are transferred to a one-dimensional ranking scale taking into account that not all elements are ranked with the same certainty. A simple general robustness parameter (E) in form of the expected number of comparisons for each ranking element is defined and correlated to the uncertainty analysis results. A simple equation relates E to the number of elements and the number of parameters, respectively. The magnitude of the ranking uncertainty is shown to increase rapidly when the E value decreases below 4-5 comparisons per element. When the E value exceeds 5 the ranking uncertainty becomes nearly constant and independent on the actual E value.     

Potential antitermite compounds from Juniperus procera extracts

Thin layer chromatography (TLC) analysis revealed that destructive distillation of Juniperus procera tree gave ten major components, whereas Croton megalocarpus tree yielded five components. This was confirmed by gas chromatography (GC). The components were isolated by column chromatography and analysed using infrared, ultra-violet, visible and mass spectroscopy (MS) techniques. The whole extract was about 30.3% of the starting material (sawdust) and consisted of 77.5% water and 22.5% oily reddish-brown layer. The extracts had alcoholic and phenolic compounds together with acids. Cedrol, a tertiary tricyclic alcohol, was found to be in the greatest proportion in the oily layer. IR spectra with a peak beyond 3000 cm(-1), UV-VIS absorption maxima at 230 nm and mass spectra with m/e 204 suggested the presence of cedrene in the extract.     

Development of a sample equilibration system for the TEOM continuous PM monitor

In recent years, scientific discussion has included the influence of thermodynamic conditions (e.g., temperature, relative humidity, and filter face velocity) on PM retention efficiency of filter-based samplers and monitors. Method-associated thermodynamic conditions can, in some instances, dramatically influence the presence of particle-bound water and other light-molecular-weight chemical components such as particulate nitrates and certain organic compounds. The measurement of fine particle mass presents a new challenge for all PM measurement methods, since a relatively greater fraction of the mass is semi-volatile. The tapered element oscillating microbalance (TEOM) continuous PM monitor is a U.S. Environmental Protection Agency (EPA) PM10 equivalent method (EQPM-1090079). Several hundred of these monitors are deployed throughout the United States. The TEOM monitor has the unique characteristic of providing direct PM mass measurement without the calibration uncertainty inherent in mass surrogate methods. In addition, it provides high-precision, near-real-time continuous data automatically. Much attention has been given to semi-volatile species retention of the TEOM method.     

Heavy metals in urban soils of East St. Louis, IL. Part II: Leaching characteristics and modeling

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produced organic and inorganic chemicals, and petroleum refineries. Following a gross assessment of heavy metals in the community soils (see Part I of this two-part series), leaching tests were performed on specific soils to elucidate heavy metal-associated mineral fractions and general leachability. Leaching experiments, including the Toxicity Characteristic Leaching Procedure (TLCP) and column tests, and sequential extractions, illustrated the low leachability of metals in East St. Louis soils. The column leachate results were modeled using a formulation developed for fly ash leaching. The importance of instantaneous dissolution was evident from the model. By incorporating desorption/adsorption terms into the source term, the model was adapted very well to the time-dependent heavy metal leachate concentrations. The results demonstrate the utility of a simple model to describe heavy metal leaching from contaminated soils.     

The photocatalytic disinfection of urban waste waters

In this paper we present the results of the photocatalytic disinfection of urban waste water. Two microbial groups, total coliforms and Streptococcus faecalis, have been used as indexes to test disinfection efficiencies. Different experimental parameters have been checked, such as the effect of TiO2, solar or UV-lamp light and pH. Disinfection of water samples has been achieved employing both UV-lamp and solar light in agreement with data shown by other authors. The higher disinfection rates obtained employing an UV-lamp may be explained by the stronger incident light intensity. Nevertheless no consistent differences have been found between TiO2-photocatalysis and direct solar or UV-lamp light irradiation at natural sample pH (7.8). At pH 5 the presence of TiO2 increases the relative inactivation rate compared with the absence of the catalyst. After the photocatalytic bacterial inactivation, the later bacterial reappearance was checked for total coliforms at natural pH and pH 5, with and without TiO2. Two h after the photocatalytic treatment, CFU increment was almost nill. But 24 and 48 h later an important bacterial CFU increment was observed. This CFU increment is slower after irradiation with TiO2 at pH 5 in non-air-purged samples.     

Monitoring, modelling and environmental exposure assessment of industrial chemicals in the aquatic environment

Monitoring and laboratory data play integral roles alongside fate and exposure models in comprehensive risk assessments. The principle in the European Union Technical Guidance Documents for risk assessment is that measured data may take precedence over model results but only after they are judged to be of adequate reliability and to be representative of the particular environmental compartments to which they are applied. In practice, laboratory and field data are used to provide parameters for the models, while monitoring data are used to validate the models' predictions. Thus, comprehensive risk assessments require the integration of laboratory and monitoring data with the model predictions. However, this interplay is often overlooked. Discrepancies between the results of models and monitoring should be investigated in terms of the representativeness of both. Certainly, in the context of the EU risk assessment of existing chemicals, the specific requirements for monitoring data have not been adequately addressed. The resources required for environmental monitoring, both in terms of manpower and equipment, can be very significant. The design of monitoring programmes to optimise the use of resources and the use of models as a cost-effective alternative are increasing in importance. Generic considerations and criteria for the design of new monitoring programmes to generate representative quality data for the aquatic compartment are outlined and the criteria for the use of existing data are discussed. In particular, there is a need to improve the accessibility to data sets, to standardise the data sets, to promote communication and harmonisation of programmes and to incorporate the flexibility to change monitoring protocols to amend the chemicals under investigation in line with changing needs and priorities.