Laboratory and field evaluation of crystallized DOW 704 oil on the performance of the Well Impactor Ninety-Six fFine particulate matter fractionator

Subsequent to the 1997 promulgation of the Federal Reference Method (FRM) for monitoring fine particulate matter (PM2.5) in ambient air, U.S. Environmental Protection Agency (EPA) received reports that the DOW 704 diffusion oil used in the method's Well Impactor Ninety-Six (WINS) fractionator would occasionally crystallize during field use, particularly under wintertime conditions. Although the frequency of occurrence on a nationwide basis was low, uncertainties existed as to whether crystallization of the DOW 704 oil may adversely affect a sampling event's data quality. In response to these concerns, EPA and the State of Connecticut Department of Environmental Protection jointly conducted a series of specialized tests to determine whether crystallized oil adversely affected the performance of the WINS fractionator. In the laboratory, an experimental setup used dry ice to artificially induce crystallization of the diffusion oil under controlled conditions. Using primary polystyrene latex calibration aerosols, standard size-selective performance tests of the WINS fractionator showed that neither the position nor the shape of the WINS particle size fractionation curve was substantially influenced by the crystallization of the DOW 704 oil. No large particle bounce from the crystallized impaction surface was observed. During wintertime field tests, crystallization of the DOW 704 oil did not adversely affect measured PM2.5 concentrations. Regression of measurements with crystallized DOW 704 versus liquid dioctyl sebacate (DOS) oil produced slope, intercept, and R2 values of 0.98, 0.1, and 0.997 microg/m3, respectively. Additional field tests validated the use of DOS as an effective impaction substrate. As a result of these laboratory and field tests, DOS oil has been approved by EPA as a substitute for DOW 704 oil. Since the field deployment of DOS oil in 2001, users of this alternative oil have not reported any operational problems associated with its use in the PM2.5 FRM. Limited field evaluation of the BGI very sharp cut cyclone indicates that it provides a viable alternative to the WINS fractionator.     

Synthesis of polyhydroxyalkanoates in municipal wastewater treatment.

Biologically derived polyesters known as polyhydroxyalkanoates (PHAs) represent a potentially "sustainable" replacement to fossil-fuel-based thermoplastics. However, current commercial practices that produce PHA with pure microbial cultures grown on renewable, but refined, feedstocks (i.e., glucose) under sterile conditions do not represent a sustainable commodity. Here, we report on PHA production with a mixed microbial consortium indigenous to an activated sludge process on carbon present in municipal wastewaters. Reactors operated under anaerobic/aerobic and aerobic-only mode and fed primary solids fermenter liquor maintained a mixed microbial consortium capable of synthesizing PHA at 10 to 25% (w/w), while reducing soluble COD by approximately 62 to 71%. More critically, an aerobic batch reactor seeded from the anaerobic/aerobic reactor and fed fermenter liquor achieved approximately 53% PHA (w/w). Results presented suggest that environmentally benign production of biodegradable polymers is feasible. We further used PHA-rich biomass to produce a natural fiber-reinforced thermoplastic composite that can be used to offset advanced wastewater treatment costs.     

Size and composition distributions of particulate matter emissions: part 1--light-duty gasoline vehicles

Size-resolved particulate matter (PM) emitted from light-duty gasoline vehicles (LDGVs) was characterized using filter-based samplers, cascade impactors, and scanning mobility particle size measurements in the summer 2002. Thirty LDGVs, with different engine and emissions control technologies (model years 1965-2003; odometer readings 1264-207,104 mi), were tested on a chassis dynamometer using the federal test procedure (FTP), the unified cycle (UC), and the correction cycle (CC). LDGV PM emissions were strongly correlated with vehicle age and emissions control technology. The oldest models had average ultrafine PM0.1 (0.056- to 0.1-microm aerodynamic diameter) and fine PM1.8 (< or =1.8-microm aerodynamic diameter) emission rates of 9.6 mg/km and 213 mg/km, respectively. The newest vehicles had PM0.1 and PM1.8 emissions of 51 microg/km and 371 microg/km, respectively. Light duty trucks and sport utility vehicles had PM0.1 and PM1.8 emissions nearly double the corresponding emission rates from passenger cars. Higher PM emissions were associated with cold starts and hard accelerations. The FTP driving cycle produced the lowest emissions, followed by the UC and the CC. PM mass distributions peaked between 0.1- and 0.18-microm particle diameter for all vehicles except those emitting visible smoke, which peaked between 0.18 and 0.32 microm. The majority of the PM was composed of carbonaceous material, with only trace amounts of water-soluble ions. Elemental carbon (EC) and organic matter (OM) had similar size distributions, but the EC/OM ratio in LDGV exhaust particles was a strong function of the adopted emissions control technology and of vehicle maintenance. Exhaust from LDGV classes with lower PM emissions generally had higher EC/OM ratios. LDGVs adopting newer technologies were characterized by the highest EC/OM ratios, whereas OM dominated PM emissions from older vehicles. Driving cycles with cold starts and hard accelerations produced higher EC/OM ratios in ultrafine particles.     

Fugitive emissions opacity determination using the digital opacity compliance system (DOCS)

Maintenance of Department of Defense (DoD) weapon systems, conducting battlefield training exercises as well as meeting military construction and/or demolition schedules, invariably generate fugitive air emissions, many of which are visible. Although there is no codified federal method for quantifying fugitive emissions opacity, many state and local air regulatory agencies have instituted enforceable fugitive emission opacity standards at DoD facilities. The current study focused on comparing the performance of the digital opacity compliance system (DOCS) with U.S. Environment Protection Agency Method 9 (Method 9) certified human observers in quantifying the visible opacity associated with fugitive emissions produced using a commercial fog generator. By systematically repositioning both DOCS cameras and Method 9-certified observers during field testing, differences in method performance as a function of observational locations were documented. At both the 30- and 300-ft off-set distances, opacity levels reported by the DOCS technology and Method 9-certified smoke readers were found to be statistically different at the 99% confidence level. Alternatively, at the 90- and 150-ft off-set distances, results suggested that there was an insignificant difference at the 99% confidence level between the two methods. Comparing the magnitude of the each method's standard deviation suggested that, at the 30-ft off-set distance, the DOCS technology was consistently more precise than Method 9-certified readers regardless of the observer's downwind distance. However, at the 90, 150, and 300-ft off-set distances, method precision seemed to vary as a function of both off-set and downwind distance. The primary factor affecting the consistency in opacity measurements appeared to be the impact of ground-level air turbulence on fog plume dispersion and transport. Field observations demonstrated that localized wind shear played a critical and decisive role in how and to what extent fugitive emissions opacity could be determined, regardless of the method selected.     

Refinery evaluation of optical imaging to locate fugitive emissions

Fugitive emissions account for approximately 50% of total hydrocarbon emissions from process plants. Federal and state regulations aiming at controlling these emissions require refineries and petrochemical plants in the United States to implement a Leak Detection and Repair Program (LDAR). The current regulatory work practice, U.S. Environment Protection Agency Method 21, requires designated components to be monitored individually at regular intervals. The annual costs of these LDAR programs in a typical refinery can exceed US$1,000,000. Previous studies have shown that a majority of controllable fugitive emissions come from a very small fraction of components. The Smart LDAR program aims to find cost-effective methods to monitor and reduce emissions from these large leakers. Optical gas imaging has been identified as one such technology that can help achieve this objective. This paper discusses a refinery evaluation of an instrument based on backscatter absorption gas imaging technology. This portable camera allows an operator to scan components more quickly and image gas leaks in real time. During the evaluation, the instrument was able to identify leaking components that were the source of 97% of the total mass emissions from leaks detected. More than 27,000 components were monitored. This was achieved in far less time than it would have taken using Method 21. In addition, the instrument was able to find leaks from components that are not required to be monitored by the current LDAR regulations. The technology principles and the parameters that affect instrument performance are also discussed in the paper.     

Assessment of pesticide contamination in three Mississippi Delta oxbow lakes using Hyalella azteca

Three oxbow lakes in northwestern Mississippi, USA, an area of intensive agriculture, were assessed for biological impairment from historic and current-use pesticide contamination using the amphipod, Hyalella azteca. Surface water and sediment samples from three sites in each lake were collected from Deep Hollow, Beasley, and Thighman Lakes from September 2000 to February 2001. Samples were analyzed for 17 historic and current-use pesticides and selected metabolites. Ten-day H. azteca survival and growth (as length and dry weight) were measured to determine the degree of biological impairment. Maximum number of detectable pesticides in surface water from Deep Hollow, Beasley and Thighman Lakes was 10, 11, and 17, respectively. Maximum number of detectable pesticides in lake sediments was 17, 17, and 15, respectively. Bioassay results indicated no observable survival effects on H. azteca exposed to surface water or sediment from any lake examined and no growth impairment in animals exposed to lake sediments. However, growth was significantly impaired in surface water exposures from Deep Hollow Lake (2 sites) and Beasley Lake (1 site). Statistically significant relationships between growth impairment (length) and cyanazine, methyl parathion, λ-cyhalothrin, chlorfenapyr, and pp′DDE surface water concentrations in Deep Hollow Lake as well as trifluralin, atrazine, and methyl parathion in Beasley Lake were observed. Although pesticide frequency and concentrations were typically greater in sediment than surface water, bioassay results indicated decreased availability of these pesticides in sediment due to the presence of clay and organic carbon. Growth impairment observed in surface water exposures was likely due to complex interaction of pesticide mixtures that were present.     

Leaded electronic waste is a possible source material for lead-contaminated jewelry

Highly leaded jewelry, often imported from China, remains widely available in the United States. Leaded electronic waste is exported from the United States to several Asian countries where solder is recovered and circuit boards are stripped of parts in small workshops. To assess whether electronic waste is being recycled into the jewelry, lead, tin and copper content of highly leaded jewelry samples were determined by atomic absorption spectrometry. Sixteen jewelry items previously determined to contain 20-80% lead by weight were analyzed. Samples were digested in nitric acid for analysis of lead and copper, and in aqua regia for analysis of tin. Six samples contained significant amounts of tin, from 20.8% to 29.9% by weight. In addition, copper was a significant minor component of five of these samples (up to 4% by weight). Copper (present at 10-40% by weight in circuit boards) was shown to rapidly move into heated lead-tin solder. The combined lead-tin-copper content of these six items ranges from 93.5% to 100%, suggestive of a solder-based source material. These results are consistent with the hypothesis that recycled circuit board solders are being used to produce some of the heavily leaded imported jewelry sold in the United States. Should this hypothesis be substantiated, it suggests that environmental policies to protect children's health must address both proper recycling of source materials as well as restrictions of the lead content in consumer goods.     

Chromate transport through columns packed with surfactant-modified zeolite/zero valent iron pellets

Chromate transport through columns packed with zeolite/zero valent iron (Z/ZVI) pellets, either untreated or treated with the cationic surfactant hexadecyltrimethylammonium (HDTMA), was studied at different flow rates. In the presence of sorbed HDTMA, the chromate retardation factor increased by a factor of five and the pseudo first-order rate constant for chromate reduction increased by 1.5-5 times. The increase in rate constant from the column studies was comparable to a six-fold increase in the rate constant determined in a batch study. At a fast flow rate, the apparent delay in chromate breakthrough from the HDTMA modified Z/ZVI columns was primarily caused by the increase in chromate reduction rate constant. In contrast, at a slower flow rate, the retardation in chromate transport from the HDTMA modified Z/ZVI columns mainly originated from chromate sorption onto the HDTMA modified Z/ZVI pellets. Due to dual porosity, the presence of immobile water was responsible for the earlier breakthrough of chromate in columns packed with zeolite and Z/ZVI pellets. The results from this study further confirm the role of HDTMA in enhancing sorption and reduction efficiency of contaminants in groundwater remediation.     

Variations in PCB concentrations between genders of six warmwater fish species in Lake Logan Martin, Alabama, USA

We collected and analyzed 955 individual fish (six species) for sexual differences in PCB bioaccumulations from a southeastern, USA reservoir. Using 2-way ANCOVAs, we found significant differences in fillet PCB concentrations between sexes for channel catfish (Ictalurus punctatus), largemouth bass (Micropterus salmoides) and spotted bass (Micropterus punctulatus). Striped bass (Morone saxatilus), black crappie (Pomoxis nigromaculatus) and freshwater drum (Aplodinotus grunniens) did not display differences between sexes in PCB concentrations. We suspect that sexual differences may be due to biological differences in reproduction, relative motility and lipid deposition. For one species (striped bass), sexual differences in PCB concentrations were inconsistent with a study in the Hudson River suggesting that sexual differences in bioaccumulations can change across ecosystems. Two species which did show sexual differences, largemouth bass and channel catfish, are often chosen as representative species (e.g., "piscivore" and "benthivore") in contaminant monitoring in many USA states indicating human consumption and risk management decisions would be improved if an equal number of male and female fish were included in composite PCBs analysis. This could reduce variability in fish PCBs data from which consumption advisories are based.