化学还原法回收含银电镀废液中的银

以Na2S2O4为还原剂,采用化学还原法回收某电镀厂含银电镀废液中的银。实验结果表明,在n(Na2S2O4)∶n(Ag+)=2.5、反应温度35℃、废水pH7.5、搅拌速率300r/min的条件下,Ag+回收率达到99.92%。对回收的银粉进行X射线衍射和扫描电子显微镜分析,分析结果表明回收的银粉纯度较高,成球形。     

硼氢化钠还原法回收电镀废液中的铜

采用NaBH4作为还原剂回收电镀废液中的铜。正交实验结果表明,各因素对剩余铜离子质量浓度的影响的显著性顺序为n(NaBH4)∶n(CuSO4)反应时间反应温度。最佳实验条件为:n(NaBH4)∶n(CuSO4)=1.50,反应温度30℃,反应时间25min。经该工艺可获得平均粒径为33nm的近球形立方晶系纳米铜粉,处理后废液中铜离子质量浓度低至0.2mg/L。在铜粉制备过程中加入非离子型表面活性剂可有效阻止晶粒长大,并提高其分散性能,使产物粒径均匀。采用苯骈三氮唑处理后的铜粉抗氧化能力明显提高。     

三元乙丙橡胶超细纤维复合膜的制备及其截留性能

以四氢呋喃和N,N-二甲基甲酰胺为溶剂,配制三元乙丙橡胶(EPDM)纺丝液,通过静电纺丝技术制备了EPDM超细纤维,进而以聚偏氟乙烯(PVDF)微滤膜为基膜制备了EPDM超细纤维复合膜。采用红外光谱(FTIR)和扫描电子显微镜(SEM)对EPDM超细纤维的结构和形态进行了表征。考察了复合膜对苯乙烯废水的截留效果和复合膜通量的变化情况。实验结果表明:EPDM超细纤维具有类似无纺布形式的多孔纤维网状结构,其直径在0.2~2.0μm之间;复合膜在操作压力为0.1MPa的条件下,处理质量浓度为100μg/mL的模拟苯乙烯废水,膜通量约为5.90mL/(cm2.h),苯乙烯去除率可达89.7%。     

壳聚糖三元接枝共聚物的合成及其阻垢性能

以壳聚糖(CTS)、衣康酸(IA)和马来酸酐(MA)为原料,以醋酸为溶剂、(NH_4)_2S_2O_8为引发剂,合成了CTS-IA-MA三元接枝共聚物。聚合反应的最佳条件为:反应温度90℃,n(CTS):n(IA):n(MA)=1:1.5:1.0,引发剂质量分数0.35%,反应时间5 h。通过傅立叶变换红外光谱(FTIR)表征,所得产物为CTS-IA-MA接枝共聚物。三元接枝共聚物质量浓度为50 mg/L、水样pH为中性或弱酸性时三元接枝共聚物对CaCO_3的阻垢效果较好。     

液相色谱-质谱法测定水中氨基甲酸酯类农药及其代谢物

建立了直接测定水中10种氨基甲酸酯类农药及其代谢物的超高效液相色谱-质谱分析方法。该方法对水样无需进行富集处理,水样过滤后就可以直接测定。实验结果表明:测定液中各氨基甲酸酯类农药及其代谢物的质量浓度与离子对峰面积在质量浓度0.5～1 000.0μg/L内具有良好的线性关系;方法检出限为0.1～5.0μg/L;加标回收率91%～103%;相对标准偏差为2%～5%。该方法具有简便快捷、灵敏度高的特点。     

溶剂热法合成SnWO_4及其可见光催化活性

采用溶剂热法合成了新型的可见光催化剂SnWO4,以甲基橙为目标污染物,考察了合成温度、合成时间和煅烧工艺对催化剂可见光催化活性的影响。实验结果表明:煅烧工艺会明显降低催化剂的光催化活性;在合成温度为180℃、合成时间为8h、未煅烧的条件下,合成的催化剂的光催化效果最好,光照90min后,对甲基橙的降解率可达99.93%。     

疏水改性阳离子聚丙烯酰胺絮凝剂的制备及其絮凝性能

通过水溶液共聚合法,以丙烯酰胺(AM)、丙烯酰氧乙基三甲基氯化铵(DAC)和2-乙烯基吡啶(2-VP)为共聚单体合成了疏水改性阳离子聚丙烯酰胺P(AM-DAC-2VP),并用红外光谱仪和核磁共振光谱仪对其结构进行了表征。实验结果表明:当w(2-VP)为1.0%、w(DAC)为30%、活性污泥pH为5、P(AM-DAC-2VP)加入量为25mg/L时,P(AM-DAC-2VP)对本实验的活性污泥絮凝能力最强,上清液透光率为92.1%;P(AM-DAC-2VP)比同条件下制备的阳离子聚丙烯酰胺P(AM-DAC)具有更好的絮凝效果。     

Fe_2O_3/膨润土微波诱导氧化处理染料废水

以膨润土为载体,采用直接沉淀法制备了Fe2O3/膨润土负载型催化剂。制备催化剂的最佳工艺条件:硝酸铁质量浓度为8.08g/L,硝酸铁与膨润土质量比为1.0,焙烧温度为350℃,焙烧时间为3h。用Fe2O3/膨润土负载型催化剂微波诱导氧化处理50mL质量浓度为50mg/L的模拟活性嫩黄废水的最佳工艺条件:催化剂加入量为0.5g,微波功率为900W,微波作用时间为5min。在此条件下模拟活性嫩黄废水脱色率达96.40%。微波诱导氧化处理模拟活性嫩黄废水的反应符合一级反应动力学方程。     

Impact of anthropogenic emissions and open biomass burning on regional carbonaceous aerosols in South China

Carbonaceous aerosols were studied at three background sites in south and southwest China. Hok Tsui in Hong Kong had the highest concentrations of carbonaceous aerosols (OC = 8.7 ± 4.5 μg/m³, EC = 2.5 ± 1.9 μg/m³) among the three sites, and Jianfeng Mountains in Hainan Island (OC = 5.8 ± 2.6 μg/m³, EC = 0.8 ± 0.4 μg/m³) and Tengchong mountain over the east edge of the Tibetan Plateau (OC = 4.8 ± 4.0 μg/m³, EC = 0.5 ± 0.4 μg/m³) showed similar concentration levels. Distinct seasonal patterns with higher concentrations during the winter, and lower concentrations during the summertime were observed, which may be caused by the changes of the regional emissions, and monsoon effects. The industrial and vehicular emissions in East, Southeast and South China, and the regional open biomass burning in the Indo-Myanmar region of Asia were probably the two major potential sources for carbonaceous matters in this region.     

Formation of shaped barium sulfate-dye hybrids: waste dye utilization for eco-friendly treatment of wastewater

Purpose

Owing to the present complexity and difficulty of concentrated dye wastewater treatment, this work aimed to synthesize a reproducible waste-sorbing material for the treatment of wastewater by forming the dye-conjugating complex hybrid.

Methods

The inorganic/organic hybridization was applied to prepare the objective material by immobilizing waster dye-Mordant blue 9 (MB) with barium sulfate (BaSO₄). The composition and pattern of the formed material were determined by spectrometry and characterized by SEM and XRD, and their formation process was clarified. The adsorption of cationic dye-basic blue BO (BB) and copper ion was investigated..

Results

The hybrid of MB alone into growing BaSO₄ formed the pineapple-like particles while that of the MB/BB-conjugating complex was the rhombus material. The adsorption of BB on the MB–BaSO₄ hybrid was probably attributed to ion-pair equilibrium and that of Cu²⁺ may result from the complexation. The treatment of dye and heavy metal wastewaters indicated that the MB hybrid material removed 99.8% BB and 97% Cu²⁺ and the dye-conjugating hybrid with growing BaSO₄ 100% MB, 99.5% BB, and 44% Cu²⁺.

Conclusion

The waste MB–BaSO₄ hybrid material is efficient to treat cationic dye and Cu²⁺ wastewater. The dye-conjugating hybridization method is the first to be advanced for in situ wastewater treatment, and it showed a combined effect for the removal of both organic dyes and heavy metals.