Processing plastics from ASR/ESR waste: separation of poly vinyl chloride (PVC) by froth flotation after microwave-assisted surface modification

The feasibility of the selective surface hydrophilization of poly vinyl chloride (PVC) using microwave treatment to facilitate the separation of PVC via froth flotation from automobile shredder residue (ASR) and electronic waste shredder residue (ESR) was evaluated. In the presence of powder-activated carbon (PAC), 60-s microwave treatment selectively enhanced the hydrophilicity of the PVC surface (i.e., the PVC contact angle decreased from 86.8° to 69.9°). The scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) results are consistent with increased hydrophilic functional groups (i.e., ether, hydroxyl, and carboxyl), amounting to significant changes in the morphology and roughness of the PVC surface after treatment. After only 60 s of microwave treatment, 20 % of the PVC was separated in virgin and ASR/ESR plastics with 33 and 29 % purity, respectively, as settled fractions by froth flotation at a 150 rpm mixing speed. The microwave treatment with the addition of PAC had a synergetic effect with the froth flotation, which brought about 100 and 90 % selective separation of PVC from the other virgin and ASR/ESR plastics, with 91 and 82 % purity. The use of the combined froth flotation and microwave treatments is an effective technology for separating PVC from hazardous waste plastics.     

Passenger head kinematics in abrupt braking and lane change events

Abstract

Objective: A test track study was conducted to quantify patterns of adult front seat passenger head motion during abrupt vehicle maneuvers.

Method: Eighty-seven men and women with a wide range of body sizes and ages participated in data collection on a closed test track in a passenger sedan under manual control by a test driver. Because a primary goal of the study was to gather “unaware” data, the participants were instructed that the study was concerned with vehicle dynamics and they were required to read from a questionnaire taped to the top of their thighs as the drive began. The first event was a hard brake (approximately 1 g) to a stop from 35?mph (56 kph). Within the space of approximately 5?min the participants also experienced an aggressive lane change, a sharp right turn with simultaneous hard braking, and a second hard braking event. A Microsoft Kinect v2 sensor was positioned to view the area around the front passenger seat. Head location was tracked using the Kinect data with a novel methodology that fit 3D head scan data to the depth data acquired in the vehicle.

Result: The mean (standard deviation) forward excursion of the estimated head center of gravity (CG) location in the first braking event was 135 (62) mm. The forward head CG excursion in the second braking event of 115 (51) mm was significantly less than that in the first, but the difference was small relative to the within-condition variance. Head excursion on the second braking trial was less than that on the first trial for 69% of participants. The mean maximum inboard head excursion in lane-change maneuvers was 118 (40) mm. Forward head excursions in braking were significantly smaller for older passengers and those with higher body mass index, but the combined factors accounted for less than 25% of the variance. Inboard head excursion in the lane-change event was significantly related to stature, but only about 7% of variance was related to body size. Head excursions for men and women did not differ significantly after accounting for body size.

Discussion: This is the first quantitative occupant dynamics study to use a large, diverse sample of passengers, enabling the exploration of the effects of covariates such as age and body size.

Conclusions: The data demonstrate that a relatively large range of head positions can be expected to result from abrupt vehicle maneuvers. The data do not support simple scaling of excursions based on body size.     

A study on engineering characteristics of asphalt concrete using filler with recycled waste lime

This study focuses on determining the engineering characteristics of asphalt concrete using mineral fillers with recycled waste lime, which is a by-product of the production of soda ash (Na(2)CO(3)). The materials tested in this study were made using a 25%, 50%, 75%, and 100% mixing ratio based on the conventional mineral filler ratio to analyze the possibility of using recycled waste lime. The asphalt concretes, made of recycled waste lime, hydrated lime, and conventional asphalt concrete, were evaluated through their fundamental engineering properties such as Marshall stability, indirect tensile strength, resilient modulus, permanent deformation characteristics, moisture susceptibility, and fatigue resistance. The results indicate that the application of recycled waste lime as mineral filler improves the permanent deformation characteristics, stiffness and fatigue endurance of asphalt concrete at the wide range of temperatures. It was also determined that the mixtures with recycled waste lime showed higher resistance against stripping than conventional asphalt concrete. It was concluded from various test results that a waste lime can be used as mineral filler and, especially, can greatly improve the resistance of asphalt concrete to permanent deformation at high temperatures.     

Evaluation of operational parameters in thermophilic acid fermentation of kitchen waste

In this study, the effect of operational parameters, such as solids retention time (SRT), pH, and substrate total solids (TS) concentration, on acid fermentation efficiency was investigated. From batch tests, it was shown that the appropriate pH range for thermophilic acidogens was around 6–7 and that the optimum pH condition was 6. From the continuous experiment, pH and SRT were shown to be the most important operational parameters for solubilization and organic acid production. In contrast, TS concentration did not show any obvious effect on chromium chemical oxygen demand (CODcr) solubilization when TS was in the range 3.5%–10%. The optimum operational conditions for thermophilic acid fermentation were an SRT of 2 days and a pH of 6. This research was carried as a part of the CREST project of Japan Science and Technology Agency.     

Toxicity identification and reduction of wastewaters from a pigment manufacturing factory

In this study, major toxicants in pigment wastewaters (i.e. raw wastewater and effluent) were determined by toxicity identification evaluations (TIEs), and changes in their toxicities due to combined gamma-ray (gamma-ray) and ozone treatments were evaluated. From TIE results using Daphnia magna, Cr(VI) and o-toluidine were identified as major toxicants in the raw wastewater with concentrations of 2.47 and 25.3mg l(-1), respectively. This was confirmed by subsequent spiking and mass balance approaches. For effluent, TIE results suggested that organic anions were likely responsible for the observed toxicities. Toxicity reduction tests showed that gamma-rays with ozone treatment after coagulation was more efficient in reducing toxicities in the raw wastewater (3.9-2.0 TU) than gamma-ray treatment alone (3.9-3.1 TU). For pigment effluent, gamma-ray/O3 treatment resulted in a complete removal of the acute toxicity.     

Placental transfer of polychlorinated biphenyls, their hydroxylated metabolites and pentachlorophenol in pregnant women from eastern Slovakia

The aim of the present study was to understand the placental transfer of polychlorinated biphenyls (PCBs), specific hydroxylated PCB metabolites (OH-PCBs), and pentachlorophenol (PCP) in blood serum, in a birth cohort from eastern Slovakia. During the period 2002-2004, cord blood specimens were collected in parallel with maternal specimens from women delivering in the two eastern Slovak districts of Michalovce and Svidnik/Stropkov. A total of 92 pairs of mother-cord specimens at delivery were selected for this study. 4-OH-CB107, 3-OH-CB153, 4-OH-CB146, 3'-OH-CB138, 4-OH-CB187, and 4'-OH-CB172 were quantified. The median concentrations of Sigma(17)PCBs, Sigma(6)OH-PCBs, and PCP in cord serum were 0.92, 0.33, and 0.69 ng/g wet wt., respectively and highly correlated with the corresponding maternal serum levels (correlations were R(2)=0.61, 0.78, and 0.82, respectively). The median cord to mother ratios of the Sigma(17)PCBs, Sigma(6)OH-PCBs, and PCP were 0.18, 0.75, and 1.10, respectively. The median ratio of the Sigma(6)OH-PCBs to the Sigma(17) PCBs in the cord serum was 0.38 from wet weight based concentrations, which was about four times higher than the ratio of these compounds in maternal serum (0.09). PCP was more abundant than any PCB or OH-PCB congener measured in cord serum. The higher cord to maternal ratios of OH-PCB metabolites as compared with the parent compounds suggests either a higher placental transfer rate or greater metabolism in the fetus as compared with the maternal compartment. These findings are consistent with their preferential binding to TTR that can cross the placenta. The cord to maternal ratio varies by congener (e.g., 4-OH-CB107=0.58, 4-OH-CB146=0.74, 3'-OH-CB138=1.01).     

Manganese peroxidase-catalyzed oxidative degradation of vanillylacetone

When 4-(4-hydroxy-3-methoxy-phenyl)-2-butanone (vanillylacetone) was tested for manganese peroxidase (MnP)-catalyzed oxidation, it was found to be degraded with the cleavage of an aromatic ring. Among numerous products of vanillylacetone oxidation, four major ones were purified by thin-layer chromatography and identified using mass spectroscopy (MS) and nuclear magnetic resonance (NMR) analysis. Three of them maintained the aromatic ring structure and were identified as 4-[6,2'-dihydroxy-5,3'-dimethoxy-5'-(3-oxo-butyl)-biphenyl]-butan-2-one, 4-(4-hydroxy-3-methoxyphenyl)-3-buten-2-one, and 4-[6,2'-dihydroxy-5,3'-dimethoxy-5'-(3-oxo-butyl)-biphenyl]-3-buten-2-one. Even though the fourth product could not be purified to a single compound, data from infrared spectroscopy showed that it did not have a benzene ring. From MS and NMR analysis, 3-(3-oxo-butyl)-hexa-2,4-dienedioic acid-1-methyl ester was tentatively suggested as the dominant species. The reaction mechanism was suggested on the basis of the structural information of these products. To our knowledge, this paper is the first report on aromatic ring cleavage of the phenolic compound by MnP.     

Two-generation toxicity study on the copepod model species Tigriopus japonicus

Previous studies on the intertidal copepod Tigriopus japonicus have demonstrated that it is a suitable model species for the assessment of acute toxicities of marine pollutants. In order to standardize T. japonicus for use in environmental risk assessment involving whole life cycle exposure, we tested nine pollutants for their effects on growth and reproduction during a two-generation life cycle exposure test. Nauplii (F 0) were exposed to a range of concentrations of each chemical in a static renewal culture system. Broods of the second generation (F1) were subsequently exposed to the same concentrations for one full life cycle. Of the seven traits (nauplius phase, development time, survival, sex ratio, number of clutch, nauplii per clutch and fecundity), only the length of the nauplius phase and development time showed a greater sensitivity to chemical exposure. Between the two sensitive traits, the period of the nauplius phase was more sensitive than cohort generation time. Biocides significantly increased the maturation period of nauplii as well as copepodids in F 0 generation. In this study, it was demonstrated that T. japonicus could also be used in reproduction and life cycle tests and it provides an opportunity for testing the chronic and subchronic toxic effects of marine pollutants. Further validation and harmonization in a multi-centric study involving other laboratories of the region will strengthen its use as a supplement to existing model species.     

Applications of Satellite Remote Sensing to Marine Pollution Studies

There are two approaches in the application of satellite sensors to marine pollution studies. Satellite sensors are used to observe and characterize ocean pollutants such as industrial wastes and oil. in addition, satellite observations provide information useful in illuminating processes such as eutrophi-cation or air-sea exchange of CO₂, that are important in determining the distribution and fate of pollutants.

Satellite technology is an important tool in monitoring and studying ocean pollution. Visible sensors have been used to observe and characterize sewage sludge and industrial wastes dumped at sea. Oil slicks have been observed with Landsat, AVHRR and SAR imagery. Besides directly detecting pollutants, satellite sensors are useful for analyzing ocean processes that are influential in the fate of pollutants. These processes include eutrophication of coastal waters and the distribution of suspended matter. the fate of excess CO₂ can be addressed using scatterometer-derived estimates of wind speeds to determine the CO₂ exchange coefficient at the sea surface on a global scale.     

A DYNAMIC SYSTEM MODEL FOR SIMULATING SEDIMENT DISCHARGE1

ABSTRACT: A dynamic sediment discharge model was developed and proposed for the simulation of watershed systems. It war developed from an expansion of splash and flow erosion relationships under steady state conditions. It was described as a general erosion model that can be reduced to forms comparable to many conceptual soil erosion and sediment yield models. The model incorporates eight parameters such as rainfall intensities, runoff rates, and previous sediment discharges. The model was tested with two small watersheds with simulation results which were very satisfactory compared to the data.