Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

超临界水氧化处理高浓度丙烯酸废水

采用超临界水氧化（SCWO）技术在连续蒸发壁式反应器内处理高浓度丙烯酸废水。实验结果表明：SCWO能有效地处理丙烯酸废水,废水COD和TOC去除率分别达到99％左右,且反应时间短;反应温度、反应压力和氧化剂加入量的增加有利于COD和TOC去除率的提高。实验得出的废水处理最佳工艺条件：反应温度693K、反应压力24～26MPa、氧化剂加入量1．0～1．5倍。对反应器出口试样进行色谱-质谱联用分析结果表明,小分子醇、醚类以及CO2和CO是主要的液相产物和气相产物。针对腐蚀和盐沉积问题,提出了预防措施。     

催化湿式氧化法处理吡虫啉农药废水

自制了Cu／Mn，Cu／Ce，Cu／Ni，Ce／Mn，Ce／Ag等催化剂，经过性能比较，选择催化活性较高且金属溶出量较小的Cu／Ni作催化剂。用催化湿式氧化法处理吡虫啉农药废水，考察了各种因素对处理效果的影响。实验结果表明：在进水pH为6．93、Cu／Ni加入量为4．0g、反应温度为190oC、氧分压为1．6MPa、反应时间为120min的条件下，COD去除率为95％；处理后废水的BOD5／COD从0．093增至0．590，可生化性明显改善。     

有机离子载入-复焙烧失法制备新型净水材料

探索了一种制备介孔复合净水材料的新方法——载入有机离子一复焙烧失法。通过实验得到的最佳工艺参数为：有机载入剂为CTMAB,有机载入剂(质量浓度5g/L)加入量4mL／g,有机离子交换反应时间2h,反应温度40℃,复焙烧失温度230℃,复焙烧失时间1．5h。在最佳工艺条件下制备的净水材料对色度为7400倍、COD为3040mg／L的染料废水的脱色率为98．9％,略优于杏壳活性炭的脱色率(98．2％);COD去除率为91．3％,与杏壳活性炭的COD去除率91．7％相差无几。净水材料的染料吸附量是添加剂升温烧蚀后产品的近85倍,是酸洗刻蚀后产品的近590倍,是原材料的900多倍,其对染料废水的净化能力整体优于杏壳活性炭。     

镉试剂2B固相萃取光度法测定水中微量银

研究了镉试剂2B固相萃取测定银的方法。在pH为9.5的硼砂-氢氧化钠缓冲介质中,乳化剂-OP存在下,镉试剂2B与银反应生成2∶1稳定络合物,该络合物可用pH使用范围为1~12的W atersX terraTMRP18固相萃取小柱富集,小柱上富集的络合物用乙醇(内含0.01 mol/L、pH为9.5的四氢吡咯-醋酸缓冲溶液)洗脱后用光度法测定,在洗脱剂介质中最大吸收波长为555 nm,摩尔吸光系数为1.04×105L/(mol.cm)。银质量浓度在0.01~1.0μg/mL内符合比尔定律,方法用于环境水样中银含量的测定,结果令人满意。     

BaO/γ-Al2O3同时吸附脱除一氧化氮和二氧化硫

利用固定床连续流动反应器研究了BaO／γ—Al2O，同时吸附模拟烟气中NO和SO2的工艺条件和再生循环使用性能，对BaO／γ—Al2O3进行了比表面积和程序升温表面反应（TPSR）等表征分析。结果表明，BaO／γ—Al2O3的适宜工艺条件是SO2与NO体积比为2．9～8．4、原料气中O2体积分数大于4．5％、吸附温度448～523K。BaO／γ—Al2O3在循环使用过程中吸附能力下降。与NOXSO吸附催化剂Na2CO3／γ—Al2O3相比，BaO／γ-Al2O3同时吸附SO2和NO的能力大、再生循环使用性能好、适宜的SO2与NO体积比范围宽、热稳定性好。将BaO／γ—Al2O3应用于NOXSO工艺可望提高该工艺的脱硫、脱氮效率。     

Effects of Preparation Parameters on Properties of Soy Protein-Based Fiberboard

The effects of manufacturing parameters on mechanical properties of medium density fibreboard (MDF) bonded with modified soy protein-based glue were studied to find an appropriate manufacture technology. Physical properties of MDF made with different amount of wax emulsion were measured. Results indicated that water repellent had no obvious influence on physical properties of soy protein-based MDF boards. The fiberboards bonded with soy protein-based glue showed stronger water resistance properties than those bonded with urea–formaldehyde (UF) resins. Furthermore, the soy protein-based MDF boards had good quality [25.2% 24 h soak thickness swell (TS), 29.9 MPa modulus of rupture (MOR), 3130 MPa modulus of elasticity (MOE)], which met requirements of Chinese national standard. Practical processing parameters were obtained by orthogonal experiment, i.e., glue content 8.0%, hot-press temperature 200 °C, and hot-press time 150 s.     

TiO2/凹凸棒土复合催化剂的制备及光催化降解活性大红

以凹凸棒土作为载体,以 TiOSO4为钛源,采用超声分散-再沉淀法制备了 TiO2粒径为 10 nm 左右的锐钛矿型 TiO2/凹凸棒土复合催化剂.并采用 X 射线衍射仪、透射电子显微镜、X 射线能谱仪对复合催化剂进行了表征.制备复合催化剂的最佳条件:凹凸棒土与 TiO2的质量比为 1:3.0,煅烧温度为 450 ℃....     

Recovery of silicon powder from kerf loss slurry waste using superconducting high gradient magnetic separation technology

A major challenge in recycling of silicon powder from kerf loss slurry waste is the complete removal of metal particles. The traditional acid leaching method is costly and not green. In this paper, a novel approach to recover high-purity Si from the kerf loss slurry waste of solar grade silicon was investigated. The metal impurities were removed with superconducting high gradient magnetic separation technology. The effects of process parameters such as magnetic flux density, slurry density, and slurry flow velocity on the removal efficiency were investigated, and the parameters were optimized. In one lot of control experiments, the silicon content was increased from 90.91 to 95.83%, iron content reduced from 3.24 to 0.57%, and aluminum content from 2.44 to 1.51% under the optimum conditions of magnetic flux density of 4.0 T, slurry density of 20 g/L, and slurry flow velocity of 500 mL/min. The result indicates that the superconducting high gradient magnetic separation technology is a feasible purifying method, and the magnetic separation concentrate could be used as an intermediate product for high-purity Si powder.

     

Approach to the management of magnesium slag via the production of Portland cement clinker

Journal of Material Cycles and Waste Management - This work aims to develop another approach to the management of magnesium slag (MS) via the production of Portland cement clinker. Thus, 0, 10, 20,...