Simulations and experiments in punching spring-steel devices with sub-millimeter features

This work demonstrates the feasibility of meso-scale (100 μm to mm) punching of multiple holes of intricate shapes in metals. Analytical modeling, finite element (FE) simulation, and experimentation are used in this work. Two-dimensional FE simulations in ABAQUS were done with an assumed material modeling and plane-strain condition. A known analytical model was used and compared with the ABAQUS simulation results to understand the effects of clearance between the punch and the die. FE simulation in ABAQUS was done for different clearances and corner radii of the punch, die, and holder. To complement modeling with real experiments and for the purpose of comparison, a set of punches and dies were made to punch out a miniature spring-steel gripper. Comparison of compliant grippers made by wire-cut electro discharge machining (EDM) and punching shows that realizing sharp interior and re-entrant corners by punching is not easy to achieve. However, the promise of realizing meso-scale parts with complicated shapes through punching is demonstrated in this work; and further work is identified and some strategies are suggested for improvement. The main contribution of this paper is in adapting the well-established punching and blanking operations to the meso-scale as a viable alternative to making miniature devices currently dominated by lithography-based techniques.     

Warm forming die design,part I: Experimental validation of a novel thermal finite element modeling code

Finite element analysis (FEA) has become an invaluable tool in the design of sheet metal stamping dies and processes. FEA has gained widespread acceptance as the best method of optimizing dies for conventional stamping processes. More recently, FEA has been shown to be an effective method of designing tooling for sheet forming processes. In this work, an FEA based approach is applied to the warm stamping (warm forming) process. This work introduces a new thermal finite element analysis software called PASSAGE®/Forming (PASSAGE) that enables the up-front design of the thermal management of warm forming dies. This thermal finite element analysis software is designed to specifically handle the forming and optimization scenarios related to the heating of a stamping die while minimizing user interface time. In this work, PASSAGE has been applied to a simple block of steel embedded with cartridge heaters to validate the prediction capability of this software under two different heating conditions. The results show that PASSAGE is capable of predicting the actual steady-state temperature distribution within the block with an acceptable level of accuracy while yielding notable information to the user with respect to specifying power requirements. A finite element software package like PASSAGE is a valuable tool that will aid greatly in the implementation of warm forming as a manufacturing process beyond the scope of the laboratory and into production.     

Investigation on the changes effected by tool profile on mechanical and tribological properties of friction stir processed AZ31B magnesium alloy

The present study investigates the effect of tool shoulder profile on the mechanical and tribological properties of friction stir processed AZ31B magnesium alloy. The tool rotational speed and feed rate are the chosen process parameters. The experiments were conducted with 3 level 2 factors full factorial design. The recorded responses were tensile strength, wear losses and corrosion rate. The results were analyzed with the help microstructures of the processed samples. The study reveals that, for concave shoulder tool, the strain hardening effect was playing a major role in determining the properties of the processed materials and for the step shoulder tool, the grain size plays a major role in determining the properties of the processed materials.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Presence of Torque Teno Virus (TTV) in Tap Water in Public Schools from Southern Brazil

Torque teno virus (TTV) was surveyed in tap water collected in schools from three municipalities located in the south of Brazil. TTV genomes were found in 11.7 % (4/34) of the samples. TTV DNA was detected in 10.5 % (2/19) of the samples collected at the city of Caxias do Sul and in 25 % (2/8) of the samples from Pelotas. Those cities have a low rate of sewage treatment. All samples from Santa Cruz do Sul, which has nearly 92 % of its sewage treated, were negative. These results suggest that the amount of sewage treated may have an effect on the detection rates of TTV DNA in drinking water in a given urban area, showing a mild negative correlation (r = ?0.76), when comparing the percentage of sewage treatment to the detection of TTV genomes. The detection rate of TTV was also compared with Escherichia coli, showing a strong correlation (r = 0.97), indicating that TTV may be a suitable marker of fecal contamination.     

Detection Method for Avian Influenza Viruses in Water

Recent events have shown that humans may become infected with some pathogenic avian influenza A viruses (AIV). Since soil and water, including lakes, rivers, and seashores, may be contaminated by AIV excreted by birds, effective methods are needed for monitoring water for emerging viruses. Combining water filtration with molecular methods such as PCR is a fast and effective way for detecting viruses. The objective of this study was to apply a convenient method for the detection of AIV in natural water samples. Distilled water and lake, river, and seawater were artificially contaminated with AIV (H5N3) and passed through a filter system. AIV was detected from filter membrane by real-time RT-PCR. The performance of Zetapor, SMWP, and Sartobind D5F membranes in recovering influenza viruses was first evaluated using contaminated distilled water. SWMP, which gave the highest virus recoveries, was then compared with a pre-filter combined GF/F filter membrane in a trial using natural water samples. In this study, the cellulose membrane SMWP was found to be practical for recovery of AIVs in water. Viral yields varied between 62.1 and 65.9% in distilled water and between 1 and 16.7% in natural water samples. The borosilicate glass membrane GF/F combined with pre-filter was also feasible in filtering natural water samples with viral yields from 1.98 to 7.33%. The methods described can be used for monitoring fresh and seawater samples for the presence of AIV and to determine the source of AIV transmission in an outbreak situation.     

Management strategies to mitigate the impacts of climate change on sea turtle’s terrestrial reproductive phase

Climate change poses a serious threat to sea turtles (Cheloniidae) as their terrestrial reproductive phase is only successful within a limited range of environmental and physical conditions. These conditions are likely to become less optimal as climate change progresses. To date, management and conservation of sea turtles has focused almost entirely on non-climatic stressors, due at least in part to practitioners not knowing what strategies to take and the feasibility and risks of potential strategies. To aid the management of sea turtles in a changing environment, we identified management strategies via a focus workshop and surveys to mitigate the impacts of climate change to the terrestrial reproductive phase of sea turtles. The effectiveness, ecological risks and potential social and logistical constraints associated with implementing each of the identified management strategies is discussed. Twenty management strategies were identified; strategies varied from habitat protection to more active and direct manipulation of nests and the nesting environment. Based on our results, we suggest a three-pronged approach to sea turtle conservation in light of climate change, where managers and researchers should: 1) enhance sea turtle resilience to climate change by mitigating other threats; 2) prioritise implementing the ‘no regret’ and ‘reversible’ management strategies identified here; and 3) fill the knowledge gaps identified to aid the trial and implementation of the potential strategies identified here. By combining these three approaches our collective toolkit of sea turtle management strategies will expand, giving us an array of viable approaches to implement as climate change impacts become more extreme.     

Design and evaluation of an atomization-based cutting fluid spray system in turning of titanium alloy

Tool life has been a vital issue in machining titanium alloys. Recently, an atomization-based cutting fluid (ACF) application has been found to be an effective approach for cooling and lubrication in micromachining operations. In this study, an ACF spray system is developed for macro-scale turning of Ti–6Al–4V. The spray system is designed to minimize interaction between the fluid droplets, and the gas nozzle to control the divergence of the fluid droplets. Experiments are conducted to study the effect of five specific ACF spray parameters including fluid flow rate, spray distance, impingement angle, and type and pressure level of the droplet carrier gas on cutting forces, tool life, and chip characteristics. It has been observed that the combination of lower pressure (150 psi) air-mixed CO₂ with a higher flow rate (20 ml/min) and a larger spray distance (35 mm) produces a significantly longer tool life and broken chips. The results also reveal that the ACF spray system can extend tool life up to 40–50% over flood cooling.     

Design and manufacturing of femoral stems for the Indian population

Several researchers have stressed the need for a proper implant-patient match in hip joint replacements, in particular, for cementless femoral stems. Some of the complications of mismatch are aseptic loosening, improper load distribution, and discomfort. In this study, the differences in dimensions between femurs of elderly Indians and those of populations from other regions are compared in order to solve the problem of a possible geometric mismatch between a selected implant and the femurs of an Indian patients are concerned. This paper also describes a methodology for implant designing from measured anthropometric data, fit evaluation, finite element (FE) stress analysis and subsequently implant manufacturing using the CAM (Computer Aided Manufacturing) technique. The machining of the Titanium alloy femoral stem is usually performed on a 5 Axis CNC (Computer Numerical Control) machining center. However, in this study the machining of the femoral stem was effectively performed on a 3 Axis CNC machining center to emphasize on economical benefits for low cost manufacturing strategy.     

Incorporating stakeholder decision support needs into an integrated regional Earth system model

A new modeling effort exploring the opportunities, constraints, and interactions between mitigation and adaptation at regional scale is utilizing stakeholder engagement in an innovative approach to guide model development and demonstration, including uncertainty characterization, to effectively inform regional decision making. This project, the integrated Regional Earth System Model (iRESM), employs structured stakeholder interactions and literature reviews to identify the most relevant adaptation and mitigation alternatives and decision criteria for each regional application of the framework. The information is used to identify important model capabilities and to provide a focus for numerical experiments. This paper presents the stakeholder research results from the first iRESM pilot region. The pilot region includes the Great Lakes Basin in the Midwest portion of the United States as well as other contiguous states. This geographic area (14 states in total) permits cohesive modeling of hydrologic systems while also providing strong gradients in climate, demography, land cover/land use, and energy supply and demand. The results from the stakeholder research indicate that, for this region, iRESM should prioritize addressing adaptation alternatives in the water resources, urban infrastructure, and agriculture sectors, including water conservation, expanded water quality monitoring, altered reservoir releases, lowered water intakes, urban infrastructure upgrades, increased electric power reserves in urban areas, and land use management/crop selection changes. For mitigation in this region, the stakeholder research implies that iRESM should focus on policies affecting the penetration of renewable energy technologies, and the costs and effectiveness of energy efficiency, bioenergy production, wind energy, and carbon capture and sequestration.