悬浮填料生物反应器处理低浓度氨氮的动力学特性分析

城市污水经一级强化处理后,NH3-N浓度为10~15mg/L,CODCr为40~60mg/L。试验利用悬浮填料床对一级强化处理出水中的氨氮进行深度处理,分析了悬浮填料表面负荷和硝化速率与水力停留时间的关系,并模拟分析了硝化速率与氨氮浓度的关系。结果表明,悬浮填料床内混合液氨氮浓度为0.5~2.5mg/L时,硝化反应符合半级反应动力学,半级反应速率常数k1/2为0.48(g/m)0.5/d;混合液氨氮浓度>2.1mg/L时,硝化反应遵循零级反应动力学,rmax为0.71g/(m2.d)。动力学理论计算值与实际运行结果基本吻合,说明动力学模型对悬浮填料床的硝化性能具有良好的预测和指导意义。     

Field demonstration of surfactant-enhanced solubilization of DNAPL at Dover Air Force Base, Delaware

This study reports on a surfactant-based flood for tetrachloroethylene (PCE) removal from a control test cell at the Dover National Test Site. The surfactant formulation (sodium dihexyl sulfosuccinate (Aerosol-MA or AMA), isopropanol and calcium chloride) was able to achieve a high concentration of PCE in swollen micelles (supersolubilization) without vertical PCE migration. The hydraulic system included eight screened wells that were operated in both vertical circulation and line drive configurations. After 10 pore volumes of flushing, the overall PCE removal was 68% (65% of which corresponded to the surfactant flooding alone). In addition, the residual PCE saturation was reduced from 0.7% to 0.2%, and the concentration of PCE in the groundwater was reduced from 37-190 mg/L before the flushing to 7.3 mg/L after flooding. Recycling the surfactant solution reduced the required surfactant mass (and thus cost, and waste) by 90%. Close to 80% of the total PCE removal was obtained during the first five pore volumes which were operated in an upward vertical circulation flow scheme. No free oil phase was observed during the test. Further analysis of multilevel sampler data suggests that most of the trapped oil remaining in the cell was likely localized in secluded regions of the aquifer, which helps explain the lower PCE groundwater concentration after remedial activities. In summary, this field study demonstrated the feasibility of surfactant-enhanced remediation to reduce the mass in the source zone and significantly reduce the PCE aqueous concentration and therefore the risk associated with the contaminant plume.     

Enhanced Fenton's destruction of non-aqueous phase perchloroethylene in soil systems

The Fenton's system is applied to the destruction of perchloroethylene (PCE) present as a dense non-aqueous phase liquid (DNAPL) in soil slurry systems; the initial concentration of PCE was 45 times higher than its aqueous solubility. Studies were conducted in two matrices: Ottawa sand and soil from Warsaw, IN. In Ottawa sand, a 60-62% decrease in PCE concentration was observed, and Cl(-) recovery was 47-58%, whereas in Warsaw soil, a 44-49% decrease in PCE concentration and a Cl(-) recovery of 40-42% were observed after the addition of 600 mM H(2)O(2) and 10 mM dissolved iron. Significantly enhanced destruction resulted during application of N-(2-hydroxyethyl) iminodiacetic acid (HEIDA) to Warsaw soil. For example, in the absence of HEIDA in Warsaw soil, 36% PCE loss and 33% Cl(-) release were observed at 600 mM H(2)O(2) and 5 mM Fe(III), while 74% PCE loss and 63% Cl(-) release were achieved at 600 mM H(2)O(2) and 5 mM Fe(III)-HEIDA. For both soils, the catalytic activities of Fe(II) and Fe(III) were nearly equivalent. These findings clearly demonstrate that system design can be optimized with regard to process variables in Fenton's treatment of DNAPL in soils.     

In vitro agonistic and antagonistic endocrine disrupting effects of organic extracts from waste water of different treatment processes

Effluents from wastewater treatment plant （WWTP） have been reported to have a broad spectrum of endocrine disrupting compounds （EDCs）. The majority of studies have focused on the occurrence of estrogenic activity, while ignoring nuclear hormone receptors （NRs） pathways. In the present study, a battery of in vitro yeast bioassays and a cell bioassay, including antagonistic and agonistic effects on estrogen receptor （ER）, androgen receptor （AR）, progesterone receptor （PR）, estrogen- related receptor （ERR） and aryl hydrocarbon receptor （AHR）, were conducted to evaluate the removal efficien- cies of EDCs by different treatment processes of a WWTP located in Beijing. Estrogenic, anti-estrogenic, anti- androgenic, anti-progesteronic, anti-ERR and the activa- tion of AHR activities were detected in samples from all treatment processes and the receiving water. The concen- tration of estrogenic contaminants with estradiol （E2） equivalent concentrations ranged from 0.82 x 10-9 to 3.54 x 10 9g Ee_EQ.L-1. The concentration of anti-estrogenic contaminants with 4-hydroxytamoxifen （4-OHT） equiva- lent concentrations ranged from 1.24 × 10-6 to 2.36 x 10-6 g 4-OHT-EQ.L-1. The concentration of anti-androgenic contaminants ranged from 2.21 x 10-s to 3.52 × 10-6g flutamide-EQ. L-1. The concentration of anti-progesteronic contaminants ranged from 3.15 x 10^-5 to 2.71 x 10^-4g RU486-EQ. L-1. The concentration of anti-ERR contami- nants ranged from 7.09 x 10-5 to 6.50 x 104 g 4-OHT-EQ × L^-10. The concentration of AHR activators ranged from 1.7 × 10-10 to 3.4 × 10^-10g TCDD-EQ-L-1. These processes including secondary clarifier, coagulation, as well as coal and sand filtration could eliminated 67.2% of estrogenic contaminants, 47.0% of anti-estrogenic contaminants, 98.3% of anti-androgenic contaminants, 88.4% of anti- progesteronic contaminants, 65.4% of anti-ERR contami- nants and 46.9% of AHR activators. WWTP effluents contain multiple receptor disruptors may have very complex adverse effects on exposed organisms.     

Environmental contamination using accumulation of metals in marine sponge,Sigmadocia fibulata inhabiting the coastal waters of Gulf of Mannar,India

Coastal marine ecosystems in many parts of the world are under unrelenting stress caused by urban development, pollutants and other ecological impacts such as building of infrastructure, land reclamation for port and industrial development, habitat modification, tourism and recreational activities. The present work is a first extensive field study using the marine sponge, Sigmadocia fibulata as a bioindicator to detect metal pollution between inshore and offshore environment of the ‘Gulf of Mannar’, India. Samples of S. fibulata were collected from different places of inshore (0.1–0.5?km) and offshore (3–5?kms) locations. Metal concentrations in water and bioaccumulation in sponges were determined by ICP-MS (Inductively coupled plasma-mass spectrometry). Enrichment of metal contamination was more in the inshore, when compared to offshore environment. Higher concentrations of metals Fe, Al, Ni, Mn, Cu, Cr, Co, Ba, Zn, V, Pb and Cd in inshore waters (3–6.4 times than offshore) may be due to the discharge of monsoonal rains, carrying a discharge of industrial and agricultural wastes and sewage directly into the coast. This is substantiated by a highly significant positive correlation between concentrations of metals in the water and accumulation in sponges. The bioaccumulation of metals in sponge tissue were in order of Fe?>?Al?>?Ni?>?Mn?>?Cu?> Cr?>?Co?>?Ba?>?Zn?>?V?>?Cd?>?Pb in both the inshore and offshore regions. Apparently, the macromolecule composition (sugars, proteins and lipids) was significantly reduced by the accumulation of metals in inshore sponges. The current findings indicated that the frequent monitoring is necessary to assess the eco-health of the marine environment by choosing bio-indicator species like S. fibulata, which provide accurate, reliable measurements of environmental quality.     

Biosorption of chromium(VI), nickel(II) and copper(II) ions from aqueous solutions using Pithophora algae

The biosorption of heavy metals is considered to be one of the best alternatives for the treatment of wastewater. The metal binding capacity of algae and acid-treated algae is investigated to find out the removal characteristics of Cr(VI), Ni(II) and Cu(II) ions from single metal solutions. Batch experiments are conducted and the study is extended to investigate the effect of pH, amount of adsorbent and adsorbate concentration on the extent of biosorption. The results indicate that the adsorption capacity of algae depends strongly on pH. The maximum adsorption of Cr(VI), Ni(II) and Cu(II) occurs at pH values of 2, 7 and 4.3, respectively. The adsorption process follows first-order kinetic equation. The data obtained are correlated with Freundlich and Langmuir adsorption isotherms.     

Effect of nickel exposure on serum amylase activity in nickel-plating workers

The objective of this study was to determine the effect of nickel (Ni) exposure on serum amylase activity in nickel-plating workers in Bangalore (India). Sixty-nine subjects using Ni during the electroplating process formed the exposed group. An equal number of age- and sex-matched subjects working in the administration section formed the control group. Urine Ni levels were determined using a flameless atomic absorption spectrophotometer. Serum amylase activity was determined using spectrophotometric method with 2-chloro-4-nitrophenyl-α-D-maltotrioside as substrate. A significant increase in urine Ni and serum amylase activity was noted in nickel platers as compared with the control group. The level of serum amylase activity was positively and significantly associated with Ni content in urine of nickel platers. Stepwise multiple regression analysis was used to assess the effects of Ni exposure, life style confounding factors and presence of gastrointestinal problems on serum amylase activity. The analysis showed that the subjects who had urine Ni levels beyond 10?µg?g^?1 of creatinine, nickel platers category, smoking and body mass index variables were significantly associated with serum amylase activity. The results of this study suggest that the increased serum amylase activity observed in nickel-exposed subjects could be used as a biomarker for investigating pancreatic function in Ni exposure.     

Removal of heavy metals from aqueous solutions using activated carbon prepared from Cicer arietinum

Removal of Cu²⁺, Cd²⁺, Pb²⁺, and Zn²⁺ from aqueous solutions by activated carbon prepared from stems and seed hulls of Cicer arietinum, an agricultural solid waste, has been studied. The influence of various parameters, such as pH, contact time, adsorbent dose, and initial concentration of metal ions on removal was evaluated. The activated carbon was characterized by FT-IR spectroscopy, X-ray diffraction, and elemental analysis. Sorption isotherms were studied using Langmuir and Freundlich isotherm models. All experimental sorption data were fitted to the sorption models using nonlinear least-squares regression. The maximum adsorption capacity values for activated carbon prepared from Cicer arietinum waste for metal ions were 18 mg g^?1 (Cu²⁺), 18 mg g^?1 (Cd²⁺), 20 mg g^?1 (Pb²⁺), and 20 mg g^?1 (Zn²⁺), respectively. The Freundlich isotherm model fit was best, followed by the pseudo-second-order kinetic model. Desorption studies were carried out with dilute hydrochloric acid for quantitative recovery of the metal ions and for regeneration of the adsorbent.     

Managing natural resources with eco-friendly technologies for sustainable rural development: a case of Garhwal Himalaya

Traditional Central Himalaya societies face a range of socio-economic and environmental problems. The potential of science and technology has not yet been adequately and appropriately harnessed to overcome the development constraints posed by the fragile Himalayan environment. Thus there is a need for large-scale establishment of technology resource centers. The Garhwal Unit of GB Pant Institute of Himalayan Environment and Development established rural technology demonstration and training centers in three different agroecological zones between 550 and 2200 m asl and in 13–15 locations, with suitable technologies based on appropriate use and management of locally available bio-resources that ensure people participation. About 35 on-site training courses were organised for about 2329 participants. The participants were given on-site demonstrations, training and technical know-how on various technologies, to enable farmers to better understand problems faced during implementation of new technologies for sustainable management of natural resources. An action research framework and training manuals were also developed in consideration of local socio-economic condition. The documentation and analysis of research (quantitative and qualitative) and data related to cost–benefit analysis of the technologies adopted by farmers generated through this study has created wider sharing of farmer training outputs, at farm level, amongst the scientific communities and with policy planners.     

Traditional crop diversity for sustainable development of Central Himalayan agroecosystems

SUMMARY

A rich diversity of traditional crops occurs generally in the Himalaya and more particularly in Central Himalaya. Over forty species of food grains are grown in traditional agroecosystems of Central Himalaya, which have been managed by the local farming communities since time immemorial. These traditional crop varieties have evolved over centuries and are well adapted to the particular area. A number of edaphic, topographic and climatic factors associated with different selection pressures over centuries of cultivation resulted in immense variations in the crop species.

The grain and by-product yield of the majority of the traditional crops cultivated across an altitudinal gradient were worked out and compared with common food crops (paddy, wheat, mustard) at two points in time (1970-74, 1990–94) and it was found that almost all the traditional crops had slightly higher yields during 1970–74 than between 1990–94. However, common food crops grown during the Kharif season had higher yields during 1990–94 whereas, Rabi season crops exhibited higher yield during 1970–74. The yield of rainfed paddy remained static over the years across the altitudinal gradient. Among the traditional crops cultivated during the Kharif and Rabi seasons in mixed and pure forms at different altitudes were Macrotyloma uniforum (at higher altitude), Parilla frutescens and Vigna mungo (at middle altitude) and Panicum miliaceum (at lower altitude) which were found to be eco-energetically efficient. Avena sativa (oat) and mixed cropping of Fagopyrum esculentum and potato had higher energy efficiency ratios whereas the latter also exhibited a higher monetary output/input ratio. Crops like paddy and wheat with mustard, grown in irrigated land were found to be more eco-energetically efficient than the same crops grown in the rainfed land. In general, traditional crops possess higher nutritive value than the common food crops. The contribution of traditional crops to the local diet (kg/capita/year) and their energy and protein equivalents were higher during both time periods. It was observed that while exporting these traditional crops, the locals of the region are highly exploited by middlemen. Despite having huge potential, traditional crop diversity of this region has been reduced to a great extent during the last two decades. Besides, the area under cultivation with these crops has been declining rapidly. However, many of these crops possess immense potential to meet the growing food demand and ensure food security of an increasing population. Therefore, a comprehensive programme of conservation through various means and improvement of agronomic yield in their natural habitats is urgently needed.