Characterization of On-Road Vehicle NO Emissions by a TILDAS Remote Sensor

ABSTRACT

A tunable infrared laser differential absorption spectrometer (TILDAS) was used to remotely sense the nitric oxide (NO) emissions from 1,473 on-road vehicles. The real-world measurement precision of this instrument in the limit of low NO concentration is 5 ppm of the vehicle exhaust, which corresponds to a 3o detection limit of 15 ppm. Our analysis of the distribution of negative concentration measurements produced during this experiment supports this claim, showing that the instrumental noise for this set of measurements was at most 8 ppm in the limit of low NO concentration. The high sensitivity of this instrument allowed us to measure the NO emissions of even the cleanest vehicles. The measured vehicle fleet NO emissions closely fit a gamma distribution with 10% of the fleet contributing about 50% of the total fleet emissions. Newer vehicles had lower NO emissions than older ones, but high NO emitters were found in every vehicle age cohort. On a vehicle-by-vehicle basis, NO emissions correlated very weakly with vehicle velocity, acceleration, power per unit mass, carbon monoxide (CO) emissions, and hydrocarbon (HC) emissions. High NO emitting vehicles could not be identified by remote sensing of CO or HC emissions and vice versa. When we compared the NO emissions for 117 vehicles measured more than one time, about half of the high NO emitters were found to be very consistent, while the other half varied significantly.     

Determination of Motor Vehicle Profiles for Non-Methane Organic Compounds in the Mexico City Metropolitan Area

ABSTRACT

Non-methane organic compound (NMOC) profiles for on-road motor vehicle emissions were measured in a downtown tunnel and parking garages in Mexico City during 1996. Hydrocarbon samples from the tunnel and ambient air samples (C2-C12) were collected using stainless steel canisters, and carbonyl compounds were collected using 2,4-dinitrophenylhydrazine (DNPH) impregnated cartridges. Canister samples were analyzed by gas chromatog-raphy/flame ionization detection (GC/FID) to ascertain detailed hydrocarbon composition. DNPH samples were analyzed by high performance liquid chromatography (HPLC). NMOC source profiles were quantified for evaporative emissions from refueling, cold start, and hot soak, and on-road operating conditions. The ultimate purpose will be to determine the apportionment of ambient NMOC concentrations using the Chemical Mass Balance (CMB) model. The tunnel profile contained 42.3 ppbC% of alkanes, 20.6 ppbC% of unsaturated compounds, and 22.4 ppbC% of aromatics. The most abundant species were acetylene with 7.22 ppbC%, followed by ipentane with 5.69 ppbC%, and toluene with 5.42 ppbC%. These results were compared with those from studies in the United States. The cold start profile was found to be similar to the tunnel profile, although there were differences in the content of acetylene, isopentane, and oxygenates. The abundance of saturated NMOC in the hot soak profile was similar to gasoline head space profiles; it was also much larger than saturated NMOC in the roadway profile.     

Characteristics of penicillin bacterial residue

A hybrid selective noncatalytic reduction/selective catalytic reduction (SNCR/SCR) system that uses two types of technology, low-temperature SCR process and SNCR process, was designed to develop nitrogen oxide (NO_x) reduction technology. SCR was conducted with space velocity (SV) = 2400 hr^?1 and hybrid SNCR/SCR with SV = 6000 hr^?1, since the study focused on reducing the amount of catalyst and both achieved 98% NO_x reduction efficiency. Characteristics of NO_x reduction by NH₃ were studied for low-temperature SCR system at 150 °C using Mn-V₂O₅/TiO₂ catalyst. Mn-added V₂O₅/TiO₂ catalyst was produced, and selective catalyst reduction of NO_x by NH₃ was experimented. NO_x reduction rate according to added Mn content in Mn-V₂O₅/TiO₂ catalyst was studied with varying conditions of reaction temperature, normalized stoichiometric ratio (NSR), SV, and O₂ concentration. In the catalyst experiment according to V₂O₅ concentration, 1 wt.% V₂O₅ catalyst showed the highest NO_x reduction rate: 98% reduction at temperature window of 200~250 °C. As a promoter of the V₂O₅ catalyst, 5 wt.% Mn was added, and the catalyst showed 47~90% higher efficiency even with low temperatures, 100~200 °C. Mn-V₂O₅/TiO₂ catalyst, prepared by adding 5 wt.% Mn in V₂O₅/TiO₂ catalyst, showed increments of catalyst activation at 150 °C as well as NO_x reduction. Mn-V₂O₅/TiO₂ catalyst showed 8% higher rate for NO_x reduction compared with V₂O₅/TiO₂ catalyst in 150 °C SCR. Thus, (5 wt.%)Mn-(1 wt.%)V₂O₅/TiO₂ catalyst was applied in SCR of hybrid SNCR/SCR system of low temperature at 150 °C. Low-temperature SCR hybrid SNCR/SCR (150 °C) system and hybrid SNCR/SCR (350 °C) showed 91~95% total reduction rate with conditions of SV = 2400~6000 hr^?1 SCR and 850~1050 °C SNCR, NSR = 1.5~2.0, and 5% O₂. Hybrid SNCR/SCR (150 °C) system proved to be more effective than the hybrid SNCR/SCR (350 °C) system at low temperature.

Implications:?NO_x control is very important, since they are the part of greenhouse gases as well as the cause of acid rain and ozone hole. A technology, so-called hybrid SNCR/SCR process, was tested using Mn-V₂O₅/TiO₂ monolithic catalyst for NO_x reduction, and the method is promising. The results of this study would provide some ideas to parties such as policy makers, environmental engineers, and so on.     

Short-term impact of olive mill wastewater (OMWW) applications on the physico-chemical and microbiological soil properties of an olive grove in Argentina

The purpose of this work was to investigate the effects of spreading olive oil mill wastewater (OMWW) on soil biochemical parameters and olive production in an organically managed olive orchard. The experiment was carried out with three different doses of OMWW (80, 160 and 500 m³ ha^?1) and a control (untreated soil). Three samplings were done at 10, 30 and 90 days after the administration of the byproduct. OMWW application differentially modified the biochemical properties of the soil analyzed. Organic matter, organic carbon, total nitrogen and extractable phosphorus soil contents increased proportionally with each increasing dose. The values of these parameters decreased gradually with time. Total microbial activity was altered and the OMWW 500 m³ ha^?1 treatment proved to be the most active when compared with the other applied doses. OMWW agricultural application also modified the structure of soil microbial communities, particularly affecting Gram positive and negative bacteria, while fungal biomass did not show consistent changes. Although there was a salinity increase in the treated soil, especially at the highest dose, the productive parameters analyzed (fruit and oil tree^?1) were not affected. In light of the obtained results, we consider that low dose of OMWW could be considered an alternative farming practice for semiarid regions.     

Behaviour and variability of local and regional oxidant levels (OX = O3 + NO2) measured in a polluted area in central-southern of Iberian Peninsula

The purpose of this work is to contribute to the understanding of the photochemical air pollution in central-southern of the Iberian Peninsula, analysing the behaviour and variability of oxidant levels (OX?=?O₃?+?NO₂), measured in a polluted area with the highest concentration of heavy industry in central Spain. A detailed air pollution database was observed from two monitoring stations. The data period used was 2008 and 2009, around 210,000 data, selected for its pollution and meteorological statistics, which are very representative of the region. Data were collected every 15 min, however hourly values were used to analyse the seasonal and daily ozone, NO, NO₂ and OX cycles. The variation of OX concentrations with NO _x is investigated, for the first time, in the centre of the Iberian Peninsula. The concentration of OX was calculated using the sum of a NO _x -independent ‘regional’ contribution (i.e. the O₃ background), and a linearly NO _x -dependent ‘local’ contribution. Monthly dependence of regional and local OX concentration was observed to determine when the maximum values may be expected. The variation of OX concentrations with levels of NO _x was also measured, in order to pinpoint the atmospheric sources of OX in the polluted areas. The ratios [NO₂]/[OX] and [NO₂]/[NO _x ] vs. [NO _x ] were analysed to find the fraction of OX in the form of NO₂, and the possible source of the local NO _x -dependent contribution, respectively. The progressive increase of the ratio [NO₂]/[OX] with [NO _x ] observed shows a greater proportion of OX in the form of NO₂ as the level of NO _x increases. The higher measured values in the ratio [NO₂]/[NO _x ] should not be attributed to NO _x emissions by vehicles; they could be explained by industrial emission, termolecular reactions or formaldehyde and HONO directly emitted by vehicles exhausts. We also estimate the rate of NO₂ photolysis, J _NO2?=?0.18–0.64 min^?1, a key atmospheric reaction that influence O₃ production and then the regional air quality. The first surface plot study of annual variation of the daily mean oxidant levels, obtained for this polluted area may be used to improve the atmospheric photochemical dynamic in this region of the Iberian Peninsula where there are undeniable air quality problems.     

Impact of chronic exposure to low doses of chlorpyrifos on the intestinal microbiota in the Simulator of the Human Intestinal Microbial Ecosystem (SHIME®) and in the rat

The impact of the insecticide chlorpyrifos (CPF) on the mammalian digestive system has been poorly described. The present study aimed at evaluating the effect of chronic, low-dose exposure to CPF on the composition of the gut microbiota in a Simulator of the Human Intestinal Microbial Ecosystem: the SHIME® and in rats. The SHIME® comprises six reactor vessels (stomach to colon). The colonic segments were inoculated with feces from healthy humans. Then, the simulator was exposed to a daily dose of 1 mg of CPF for 30 days. The changes over time in the populations of bacteria were examined at different time points: prior to pesticide exposure (as a control) and after exposure. In parallel, pregnant rats were gavaged daily with 1 mg/kg of CPF (or vehicle) until the pups were weaned. Next, the rats were gavaged with same dose of CPF until 60 days of age (adulthood). Then, samples of different parts of the digestive tract were collected under sterile conditions for microbiological assessment. Chronic, low-dose exposure to CPF in the SHIME® and in the rat was found to induce dysbiosis in the microbial community with, in particular, proliferation of subpopulations of some strains and a decrease in the numbers of others bacteria. In compliance with European guidelines, the use of the SHIME® in vitro tool would help to (1) elucidate the final health effect of toxic agents and (2) minimize (though not fully replace) animal testing. Indeed, certain parameters would still have to be studied further in vivo.     

Synthesis of α-Fe2O3 nanofibers for applications in removal and recovery of Cr(VI) from wastewater

Purpose

Nanomaterials such as iron oxides and ferrites have been intensively investigated for water treatment and environmental remediation applications. The purpose of this work is to synthesize α-Fe₂O₃ nanofibers for potential applications in removal and recovery of noxious Cr(VI) from wastewater.

Methods

α-Fe₂O₃ nanofibers were synthesized via a simple hydrothermal route followed by calcination. The crystallographic structure and the morphology of the as-prepared α-Fe₂O₃ nanofibers were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. Batch adsorption experiments were conducted, and Fourier transform infrared spectra were recorded before and after adsorption to investigate the Cr(VI) removal performance and adsorption mechanism. Langmuir and Freundlich modes were employed to analyze the adsorption behavior of Cr(VI) on the α-Fe₂O₃ nanofibers.

Results

Very thin and porous α-Fe₂O₃ nanofibers have been successfully synthesized for investigation of Cr(VI) removal capability from synthetic wastewater. Batch experiments revealed that the as-prepared α-Fe₂O₃ nanofibers exhibited excellent Cr(VI) removal performance with a maximum adsorption capacity of 16.17 mg g^?1. Furthermore, the adsorption capacity almost kept unchanged after recycling and reusing. The Cr(VI) adsorption process was found to follow the pseudo-second-order kinetics model, and the corresponding thermodynamic parameters ΔG°, ΔH°, and ΔS° at 298 K were calculated to be ?26.60 kJ?mol^?1, ?3.32 kJ?mol^?1, and 78.12 J?mol^?1 K^?1, respectively.

Conclusions

The as-prepared α-Fe₂O₃ nanofibers can be utilized as efficient low-cost nano-absorbents for removal and recovery of Cr(VI) from wastewater.     

焦化废水处理过程外排污泥中重金属形态特征及其潜在环境风险

焦化废水处理过程所排放污泥中重金属的含量及化学形态是否构成环境风险将直接影响污泥处置方法的选择,为此,实验采用BCR顺序提取法分析了焦化废水处理站外排污泥中重金属(Cd、Hg、Pb、Cr、As、Ni、Zn、Cu和Mn)的形态特征,并采用地累积指数(Igeo)和潜在生态危害指数(RI)评价了重金属对土壤的潜在环境风险。研究结果表明:除Ni主要以可氧化态存在外,焦化废水外排污泥中其他几种重金属元素主要存在于残渣态,重金属元素的含量低于《城镇污水处理厂污染物排放标准(GB18918—2002)》中的控制限值;与城市污泥相比,焦化废水外排污泥具有低Pb、Cr、Zn、Cu含量,而高Cd、Hg、Mn含量的特点;基于Igeo和RI的评价结果,Cd和Hg是外排污泥中具有一定环境风险的元素,需要考虑其下游去向。焦化废水处理外排污泥中主要存在残渣态重金属成分,不表现为很高的环境风险,其处置应重点考虑其中有机污染物特别是POPs。     

风量对高频气力分选机分选效率及金属分布规律的影响——以废弃印刷电路板粉末为例

以金属高富集粒级0.5～0.125 mm的废弃电路板为分选物料,通过ICP-AES测定分选产品,研究了风量对高频气力分选机分选效率及金属分布规律的影响.结果表明,风量变化对分选效率及金属分布规律影响显著,当风量为200m3/h时分选效率达到最大值78.23％,铜品位为86.745％,相比原料中铜品位13.96％,富集约6.2倍.随着风量的变化,金属的分布呈现规律性变化:密度比铜大或与铜相差不多的金属颗粒(铅、铂和锌等),其变化规律与铜相似,回收率在85％左右变化;密度比铜小很多的金属颗粒(铝、镁等),由于其密度与分选物料中的非金属非常接近,在分选过程中会随非金属带人轻产物中去,从而造成重产物中铝和镁品位最低,甚至低于其在原料中的品位.所以若要分离富集铝和镁,须对分选后的物料进行二次分选.     

六铝酸盐催化剂的催化还原脱硫脱硝性能

采用共沉淀法制备Cu和Fe掺杂的六铝酸盐催化剂(SrCuxFe1-xAl11O19-δ,x为0,0.2,0.4,0.5,0.6,0.8,1),通过XRD、TPR、BET等技术方法对催化剂的结构及性质进行了研究,并考察了以CO为还原剂的催化脱硝活性。结果表明,用碳酸铵作为沉淀剂在1 200℃焙烧4 h可以形成完整的六铝酸盐晶型,Cu和Fe能够取代Al3+,很好地促进六铝酸盐晶体结构的形成;SrCuxFe1-xAl11O19-δ催化剂有很好的脱硫脱硝催化活性,此类型的催化剂均使SO2、NO的转化率在空速为6 000 h-1下达到了80%和90%以上。向体系中加入氧气会对催化活性有较大影响。