Airborne Particulate Emissions from a Chromic Acid Anodizing Process Tank

Particulate mass concentration, particle size distribution, and particle chemical composition measurements have been conducted on the gases exhausting from a chromic acid anodizing process tank. Particle mass concentrations in the 200 to 20,000 μg/m³ range were measured using open-faced filters (47 mm diameter) adjacent to the process tank liquid and with closed filters (90 mm diameter) in the exhaust duct. Particle size distributions, measured using University of Washington Mark 3 and Mark 20 Cascade Impactors, showed the particle aerodynamic mass median diameter was about 3 microns. Chemical analysis of the particle samples obtained by the Modified EPA Method 5 sampling train, the Mark 20 UW Cascade Impactors, and by the 47 mm and 90 mm diameter filters showed Cr⁺⁶ concentrations in the 20 to 1,500 μg/m³ range with over 99 percent of the chromium in particles larger than 1.0 microns diameter. An integrating nephelometer was used to measure the light scattering coefficient of the exhaust gases upstream of the wet scrubber. The light scattering coefficient increased by a factor of about 2–3 over the background level during the 40 minute time period while a part was being anodized. The bscat values ranged from 3 × 10^?5 to 3 × 10^?4 meters^?1 for the aerosol particles less than about 6 microns aerodynamic diameter.     

Nitrogen Compounds other than NO in Automobile Exhaust Gas

Recent studies of organic pyrolyses in the presence of nitric oxide have shown that various nitogen compounds, such as hydrogen cyanide (HCN) and aceto-nitrile (CH₃CN) are formed. This suggests the possibility that such compounds will be found in internal combustion processes, and may be present in automobile exhaust gases. The present paper describes some gas-chromatographic and wet analyses of exhaust gases. It is concluded that the amounts of hydrogen cyanide are less than 1 ppm, but that various organic nitrogen compounds may reach a level of about 100 ppm. The significance of these results is discussed.     

Performance and Cost Comparisons between Fabric Filters and Alternate Participate Control Techniques

A study was conducted to evaluate performance and cost comparisons of fabric filters and alternate fine particulate control techniques. In relating the removal of fine particulate to costs, due to the lack of fractional efficiency data, it was found necessary to treat a specific application in order to make the study manageable. The case chosen is that of the coal fired industrial boiler since Enviro-Systems has a pilot program in this application area.     

Economics and Alternatives for Sulfur Removal from Coke Oven Gas

Two processes are currently being employed in North America for the desulfurization of coke oven gas, the Vacuum Carbonate System, and the Stretford System. A third, the Sulfi-ban Process, which was recently announced, now has several plants scheduled for construction. Overall operating requirements for each of these processes are considered in detail. Emphasis is placed on an identification of power and steam requirements, the types and amounts of solid and/or liquid waste streams produced together with methods for their treatment, and the net desulfurization efficiencies achieved by each process. Detailed estimates of capital and operating costs for desulfurization are considered, and equipment needs for environmental control requirements are discussed.     

Desulfurization of Flue Gases in A Fluidized Bed of Modified Limestone

This publication concerns the dry removal of SO₂ from gases using limestone absorbents. It reports bench-scale experiments made with commercial samples of powdered limestone (CaCO₃) activated by addition of a cheap substance, namely CaCl₂. The absorption was carried out in a fluidized bed traversed by the flue gases, between 600° and 900° C. The degree and rate of transformation of CaCO₃ to CaSO₄ in the presence of SO₂ and air have been compared for unmodified and modified absorbents. Initial rates of reaction, and the variation of the rate of absorption with time have been measured. The influence of the SO₂ content of the gas has been assessed. At 700° C, the maximum degree of transformation of activated limestone to sulfate exceeds 90%, whereas untreated CaCO₃ transforms only to 16–20%. At the same temperature, more than 90% of SO₂ contained In a gas carrying 0.35% SO₂ is removed. Because of the much smaller quantity of solid absorbent required, dry absorption processes based on the modified absorbents might get renewed interest. The modified absorbents might also be used for in situ absorption in fluidized bed combustion, in which the temperatures are in the range studied in the present paper.     

Heavy trucks, conspicuity treatment, and the decline of collision risk in darkness

IntroductionThe influence of amendments to Federal Motor Vehicle Safety Standard (FMVSS) 108, requiring conspicuity treatments on heavy tractors and trailers, was determined in analyses of the odds of fatal collisions in darkness.MethodComparisons were made between crashes in which conspicuity treatment was likely relevant, and those in which it was likely irrelevant.ResultsOver 23 years, the odds that a fatal collision involving a heavy truck occurred in darkness declined by 58% among relevant crashes, while little decline was observed for irrelevant crashes. Disaggregation into crash types revealed the largest declines occurred in fatal rear-end and angle collisions. A parallel analysis of light vehicles also found declines but no differences among crash type. Similar trends were also observed for nonfatal rear end collisions.ConclusionThe results suggest that detection failure may have contributed to the risk of striking a tractor-semitrailer in darkness, and that conspicuity treatments have reduced this risk.Impact on IndustryConspicuity treatments appear to reduce risk of collision into heavy trucks in darkness. It is likely that this benefit would also extend to other vehicles that are not included in the FMVSS 108 regulation (e.g., buses, single unit trucks, recreational vehicles), although many are so equipped, regardless of the regulation.     

Assessment of medical care costs of injuries due to alcohol-related motor vehicle crashes

The purpose of this study was to estimate the total medical care costs of individuals injured in motor vehicle crashes and in crashes where alcohol was involved. Crashes were studied that involved 2,728 vehicle occupants and 191 pedestrians with injuries as reported in 1979 by the National Accident Sampling System, a probability sample of all motor vehicle crashes occurring in the united States. Medical care costs were assigned by using Abbreviated Injury Scale codes in accordance with other published research. Determination of alcohol involvement was based on crash characteristics. Results indicate that 20.2 % of medical care costs for motor vehicle crash injuries may be due to crashes where alcohol was involved. It was estimated that alcohol-related motor vehicle crashes cost between $434 million and $483 million in medical care alone in the United States in 1979.