Dry FGD at United Power Association’s Stanton Station

The United Power Association’s dry FGD system at Stanton, North Dakota was the first utility-operated lime spray dryer to be put into service in the United States. At 60 MW in size, it utilizes a single spray dryer vessel with three rotary atomizers and a ten-compartment fabric filter. It is currently operating at better than expected efficiency and Is meeting state and federal air quality requirements. Start-up and operation have shown that certain areas of design and operating conditions are critical to reliable operation. Flue gas, slurry, and water distribution and mixing must be carefully controlled if reliable, long term operation is to be achieved. Likewise, water chemistry Is Important in the reagent preparation equipment. Start-up of the system was accomplished In a step-wise fashion to bring the baghouse on line first, followed by the spray dryer. The spray dryer was operated at gradually lower outlet temperatures until design conditions were met. Measures taken since start-up to ensure reliable operation, and operation over an eighteen month period are discussed. Both particulate and SO₂ emission performance are evaluated.     

Evaluation of RAM Model for Cleveland,Ohio, Part II

Coal combustion is the primary contributor to atmospheric pollution in China, especially so In big cities. Particulate matter and sulfur dioxide are the two main pollutants worthy of attention. Concentration of suspended particles is usually higher in northern cities than in southern cities and higher in winter than in summer. In the case of sulfur dioxide, concentrations are high in the heating season (wintertime) in northern cities, but also in some of the cities in the southwest part of China. Rainfall with pH less than 5.6 occurs mostly to the south of the Yangtze River, especially so in the cities of Chongqing and Gueiyang, and their neighboring areas, and also In the southwest part of China. No acid rain, however, has been found in Beijing and Tianjin. Although the formation of acid rain can thus be thought of as dependent on the presence of enough sulfur dioxide, other factors such as airborne particles and ammonia also play an important role. The difference is, therefore, explained and theorem postulated with supporting data. Ways of abating atmospheric pollution are, in essence, related to improved coal burning; some simple methods are suggested for nationwide control options.     

Reducing Interference Effects in the Chemiluminescent Measurement of Nitric Oxides from Combustion Systems

Experiments were carried out to determine the relative chemiluminescence quenching efficiencies as a function of third body concentration for each of the common combustion products, H₂O, CO₂, CO, H₂, O₂ and Ar. These results are compared with those of other investigators. The effect of reaction chamber pressure on analyzer response and the development of an analyzer design which incorporates an adjustable sample capillary inlet capable of maintaining a constant molar flow rate of sample gas to the reaction chamber are discussed. The effect of carbon monoxide interference on chemiluminescent NO_x measurement has been isolated and found to be significant. A means of correcting NO, measurements for these CO interference effects is described. Quantification of NO and NO₂ absorption in liquid water in NO_x sampling systems has been made. Recommendations for sample system designs to handle the presence of water in the sample gas are made.     

1985 Update,Operating History and Current Status of Fabric Filters in the Utility Industry

Stringent particulate emissions limits and increasing awareness of stack opacity is leading the utility industry to use high efficiency particulate control systems. In response to this trend, the Electric Power Research Institute (EPRI) is conducting several research programs aimed at improving the operation, maintenance and performance of particulate control systems. One of these programs, RP-1401, “Reliability Assessment of Particulate Control Systems,” is developing operation, maintenance and design data bases for both electrostatic precipitators and fabric filters. This paper discusses some of the intermediate findings of the work done on fabric filters.     

Development of Federal Air Standards to Reduce Sulfur Dioxide Emissions from New Industrial Boilers

Federal new source performance standards to control air emissions of sulfur dioxide from new industrial boilers were proposed by EPA on June 19, 1986. These standards would require boiler owners to reduce SO₂ emissions by 90 percent and meet an emission limit of 1.2 lb/MM Btu of heat input for coal-fired boilers and 0.8 lb/MM Btu for oil-fired boilers. In developing these standards, several regulatory options were considered, from standards that could be met by firing low sulfur fuels to standards that would necessitate flue gas treatment. The environmental, economic, and cost impacts of each option were analyzed. National impacts were estimated by a computer model that projects the population of new boilers over the 5-year period following proposal, predicts the compliance strategy that will be used to comply with the particular option (always assuming that the lowest cost method of compliance will be selected), and estimates the resulting emission reductions and costs. Impacts on specific industries and on model boilers were also analyzed. This paper focuses on these analyses and their results. The Agency's conclusions from these analyses, which led to the decision to establish percent reduction standards, are provided, and the proposed SO₂ standards are summarized. The proposed standards also include an emission limit for particulate matter from oil-fired boilers (0.1 lb/MM Btu). However, this article focuses only on the SO₂ standards.     

Rotary Kiln Incineration II. Laboratory-Scale Desorption and Kiln-Simulator Studies—Solids

With landfill costs increasing and regulations on landfilling becoming more stringent, alternatives to conventional hazardous waste treatment strategies are becoming more desirable. Incineration Is presently a permanent, proven solution for the disposal of most organic contaminants, but also a costly one, especially in the case of solids which require some auxiliary fuel. The goal of this research is to develop an understanding of the phenomena associated with the evolution of contaminants from solids In the primary combustor of an Incineration system. A four-fold approach is being used. First, a bench-scale particle characterization reactor was developed to study the transport phenomena on a particle basis, where the controlling processes are mainly intraparticle. Second, a bed-characterization reactor was built to examine the controlling transport phenomena within a bed of particles, where the processes are primarily interparticle. The results of these studies can be applied to any primary combustor. A pilot-scale rotary kiln was developed to study the evolution of contaminants from solids within a realistic temperature and rotation environment. Finally, in situ measurements are being obtained from a full-scale rotary-kiln.

This paper describes results obtained in a study using a commercial sorbent contaminated with toluene. The data are from the particle-characterization reactor and the rotary-kiln simulator. The results show that the method of contamination and charge size do not have a large effect on desorption, while temperature and contaminant concentration are important parameters In the evolution of contaminants in a rotary kiln.     

Determination of Room Temperature OH Rate Constants for Acetylene,Ethylene Dichloride,Ethylene Dibromide,p-Dichlorobenzene and Carbon Disulfide

A relative rate procedure was used to measure hydroxyl rate constants at room temperature in the presence of oxygen. The photolysis of methyl nitrite in the presence of nitric oxide was used to generate OH radicals. The rate of loss of the test compounds was measured relative to that of ethane (k_OH = 2.74 × 10^-13 cm³ molec^-1 s^-1). The rates obtained at 297 ± 2 K are: acetylene = (7.8 ± 1.6) × 10^-13 cm³ molec^-1 s^-1,1,2-dichloroethane (2.8 ± Q.6) × 10^-13 cm³ molec^-1 s^-1, 1,2-dibromoethane (2.4 ± 0.5) × 10^-13 cm³ molec^-1 s^-1, p-dichlorobenzene (4.3 ± 0.9) × 10^-13 cm³ molec^-1 s^-1 and carbon disulfide (29 ± 6) × 10^-13 cm³ molec^-1 s^-1. Under a proposed EPA rule, this OH rate determination procedure could be used to determine if a given volatile organic will be subject to control for reduction of photochemical ozone.     

Transportation-Related Volatile Hydrocarbon Source Profiles Measured in Atlanta

Abstract

Samples representative of transportation-related hydrocarbon emissions were collected as part of the 1990 Atlanta Ozone Precursor Monitoring Study. Motor vehicle emissions were sampled in canisters beside a roadway in a tunnel-like underpass during periods of heavy traffic. Airport and aircraft emissions were approximated by canister samples obtained at a major airport facility. Three octane grades of gasoline were purchased from six major vendors in Atlanta. Canister samples were prepared using these fuels to approximate the whole gasoline and gasoline vapor composition of the fuels in use during the study. All samples were analyzed by gas chromatography/flame ionization detection (GC/FID) for their hydrocarbon content. Detailed speciated hydrocarbon profiles were developed from this source sampling and analysis program for use in the Chemical Mass Balance (CMB) model. Profiles presented and discussed here represent the hydrocarbon composition of emissions from a roadway, composite headspace gasoline at two temperatures, composite whole gasoline, whole gasoline at three octane grades, and an airport. The roadway profile is compared with similar profiles in the literature, and recommendations are made regarding its use in the CMB model. The roadway and fuel profiles are discussed in the context of the MOBILE5 model outputs. The headspace gasoline vapor profile presented here is compared with a headspace gasoline vapor profile calculated from the whole gasoline profile by means of Raoult’s law. Agreement between the measured and calculated headspace profiles is excellent. The airport profile demonstrates the importance of high molecular weight volatile hydrocarbons in airport and aircraft emissions.     

Spatial Variation in Acidic Sulfate and Ammonia Concentrations within Metropolitan Philadelphia

Abstract

Acidic sulfate concentrations were measured in metropolitan Philadelphia during the summers of 1992 and 1993, as part of a continuing effort to characterize particle concentrations in urban environments. Sampling was performed simultaneously at eight sites located within and around metropolitan Philadelphia. Sites were selected based on their population density and on their distance and direction from the city center. Air pollution sampling was conducted every other day during the summer of 1992 and every day during the summer of 1993. All samples were collected for 24-h periods beginning at 9 a.m. (EDT). All acidic sulfate and ammonia samples were collected using modified Harvard-EPA Annular Denuder Systems (HEADS).

In this paper, we examine the spatial variation in acidic sulfate and ammonia concentrations within the metropolitan Philadelphia area. We also identify factors that may influence their variation and develop models to predict their concentrations. Outdoor sulfate (SO₄ ^2?) concentrations were uniform within metropolitan Philadelphia; however, aerosol strong acidity (H⁺) concentrations varied spatially. This variation generally was independent of wind direction, but was related to local factors, such as the NH₃ concentration, population density, and distance from the center of the city. Physico-chemical models, which were developed using data collected during the summer of 1992, were excellent predictors of 24-h and mean summertime H⁺ concentrations measured during the summer of 1993. Models accounted for 78% of the variation in 24-h H⁺ levels. Results suggest that a single stationary ambient (SAM) monitor would be sufficient to estimate SO₄ ^2? exposures for populations living in Philadelphia. For H⁺, however, multiple monitoring sites or models should be used to determine the outdoor H+ exposures of populations living in urban environments, although a single SAM site may provide an excellent index of H⁺ variation over time.