A dynamic statistical experiment for atmospheric interactions

Interactions among atmospheric parameters exist at different scales. The pristine approach for observational or model data analysis involves changing the input parameters one at a time (OAT) and studying the effect on the system. Limitations of this approach for atmospheric applications are discussed. A fractional factorial (FF) based study is evolved and a methodology is outlined involving dynamic graphical analysis. Observational data from the FIFE and HAPEX‐MOBILHY experiments are utilized with a vegetation and soil moisture scheme dynamically coupled in a planetary boundary layer model to demonstrate the robustness of this approach. Both low‐resolution and high‐resolution designs are considered. Various aspects of the vegetation‐atmosphere interactions are delineated. Results obtained from the interaction‐based FF approach differ considerably from the earlier OAT‐type studies.     

Trends in motor-vehicle related air pollutants in central London

Results of intermittent monitoring of six aromatic hydrocarbons (benzene, toluene, ethyl-benzene, m-xylene, p-xylene and o-xylene), carbon monoxide and oxides of nitrogen over a thirteen year period at a site in central London (Exhibition Road) are presented. Four monitoring regimes were undertaken; namely, 1979, 1982/83, 1986/87 and 1991/92. The summertime daytime mean ambient concentrations of the measured parameters at this site are presented. The reported concentrations show a reduction from 1979 to 1992 by approximately a factor of two, despite national increases in motor fuel consumption and the volume of traffic. Relevant European Community legislation covering emissions from motor-vehicles are outlined and comparisons are made with emissions from motor vehicles predicted from the UK national inventory. The importance of the frequency of measurements was also noted.     

A ten channel fibre-optic device for distributed sensing of underground hydrocarbon leakage

With millions of fuel storage tanks and oil pipelines installed around the world, there is inevitably frequent leakage of potentially hazardous hydrocarbons. As many of these installations are below ground, it can often be many years before the extent of the leak is discovered. We have previously reported the development of a sensor for the detection of such subterranean leaks, using infrared reflectometry to interrogate a hydrocarbon sensitive membrane. However, a single sensor cannot provide any information about the flow rate or direction of the leak. This paper describes the extension of the technology to a multi-channel distributed sensing system, using optical fibres capable of distributing the sensors over large subterranean areas. Results are reported from the evaluation of the device, which consisted of monitoring the movement of different hydrocarbons (gasoline, diesel and insulating oil) through a vertical sand-filled vessel.     

Detecting and characterising sources of persistent organic pollutants (PAHs and PCBs) in surface sediments of an industrialized area (harbour of Trieste, northern Adriatic Sea)

A sediment sampling based on a two-dimensional mapping was performed in the harbour of Trieste (northern Adriatic Sea), considering 28 sites exposed to pollutant inputs from harbour and industrial activities. Polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) were determined in surface sediments, because these very persistent pollutants seem to be responsible for the depletion of benthic populations observed in this area. The correlation matrix indicates that PAHs and PCBs are non-correlated, and probably have different sources. Both cluster analysis performed on the sampling sites and graphical drawing of the PAH sediment contents make it possible to locate along the shoreline a band of more polluted sediments, clustered around a site facing a steelmaking factory, to be considered as the main source point for PAHs. The evaluation of phenanthrene to anthracene (P/AN) and fluoranthene to pyrene (FL/PY) ratios permits the assessment of the pyrolytic, industrial origin of these PAHs, rejecting a second possible source of hydrocarbons (i.e., an oil-pipeline terminal, situated near the steelmaking factory). Graphical drawing of the total PCB iso-concentrations reveals a different source-point for this other category of very persistent pollutants.     

Adsorption characteristics of a phenoxy acetic acid herbicide on activated carbon

The adsorption of 2,4-dichlorophenoxyacetic acid (2,4-D) by two powdered coal activated carbons was studied in aqueous solution. The modelling of the adsorption equilibrium showed that the adsorption of 2,4-D fitted a Langmuir isotherm. Adsorption was influenced by the activated carbon type, adsorbent concentration and solution characteristics. The adsorption was found to decrease with an increase in pH over the range 1.5-9. Maximum adsorption occurred at pH approximately 2.5, which corresponds to the 2,4-D pKa value. The amount of 2,4-D adsorbed was also found to depend on the NaCl concentration.     

A novel sensor for monitoring leakage of petroleum and other liquid hydrocarbons into soil environments

This paper describes the use of a potentially implantable infrared reflectometer for the qualitative detection of petroleum and a number of other hydrocarbon solvents. A rugged, low-power, re-useable sensor was evaluated in the laboratory for its ability to detect petrol in soil. A hydrophobic fluoropolymer was used as the sensing surface due to its high selectivity for petroleum hydrocarbons. The photocurrent reflected by this surface from a near IR source was measured to test for petroleum saturation within the membrane, which in turn was an indicator of petroleum in the surrounding soil. The simplicity in the sensor design enabled a stable, low cost detection method for petroleum and other hydrocarbons, ideal for use in sub-surface applications.     

Indoor and outdoor formaldehyde concentrations in homes in residential areas in Greater Cairo

Indoor and outdoor measurements of formaldehyde were conducted at seven flats located in residential areas in Greater Cairo, during spring and summer seasons 1999. The mean daytime formaldehyde concentrations in kitchens, bedrooms and living rooms were 89, 100 and 100 ppb, respectively, in the seven flats. Significant positive correlations were found between the concentrations of formaldehyde found in these three rooms. On the other hand, no significant differences were found between the mean formaldehyde concentrations in these three rooms. The maximum mean concentration of formaldehyde (147 ppb) was recorded in a new flat, while the minimum concentration (43 ppb) was observed in an old flat. The maximum hourly and daytime concentrations were 350 and 225 ppb, respectively. Air temperature, relative humidity and the age of the flat are factors affecting the emission and concentration of formaldehyde. The maximum indoor and outdoor formaldehyde concentrations were recorded during the summer season. During the spring, 38% of the samples indicated that the concentration of formaldehyde in the seven flats exceeded 0.1 ppm, the American Society of Heating, Refrigerating, and Air Conditioning Engineers' (ASHRAE) standard; in the summer, this figure increased to 53%.     

Evaluation of airborne lead in the welding working environment

Manual and automatic welding machines (which use leaded alloys) are considered to be important sources of the emission of lead fumes into the general air of the working environment. Three workplaces at a television factory were selected for the present study, to determine the control class of the working unit. The concentrations of conventional measurements ("A" sampling points) were lower than the administrative control level (statutory standard of lead, 150 microg m(-3)), whereas the maximum concentration of 264.1 microg m(-3) ("B" sampling point) was higher at one working unit than the administrative control level. However, the control classes varied between class III (bad) and class I (good).     

Performance evaluation of a sorbent tube sampling method using short path thermal desorption for volatile organic compounds

Air sampling, using sorbents, thermal desorption and gas chromatography, is a versatile method for identifying and quantifying trace levels of volatile organic compounds (VOCs). Thermal desorption can provide high sensitivity, appropropriate choices of sorbents and method parameters can accommodate a wide range of compounds and high humidity, and automated short-path systems can minimize artifacts, losses and carry-over effects. This study evaluates the performance of a short-path thermal desorption method for 77 VOCs using laboratory and field tests and a dual sorbent system (Tenax GR, Carbosieve SIII). Laboratory tests showed that the method requirements for ambient air sampling were easily achieved for most compounds, e.g., using the average and standard deviation across target compounds, blank emissions were < or = 0.3 ng per sorbent tube for all target compounds except benzene, toluene and phenol; the method detection limit was 0.05 +/- 0.08 ppb, reproducibility was 12 +/- 6%, linearity, as the relative standard deviation of relative response factors, was 16 +/- 9%, desorption efficiency was 99 +/- 28%, samples stored for 1-6 weeks had recoveries of 87 +/- 9%, and high humidity samples had recoveries of 102 +/- 12%. Due to sorbent, column and detector characteristics, performance was somewhat poorer for phenol groups, ketones, and nitrogen containing compounds. The laboratory results were confirmed in an analysis of replicate samples collected in two field studies that sampled ambient air along roadways and indoor air in a large office building. Replicates collected under field conditions demonstrated good agreement except for very low concentrations or large (> 41 volume) samples of high humidity air. Overall, the method provides excellent performance and satisfactory throughput for many applications.