Investigation of Mtbe and Aromatic Compound Concentrations at a Gas Service Station

Methyl tert-butyl ether (MTBE) has been used as a fuel additive at levels of 2–11% in Taiwan for the past decade. The purpose of this additive is to enhance the octane, replace the use of lead-based anti-knock gasoline additives and reduce aromatic hydrocarbons. However, it is possible that oxygenated fuel has a potential health impact. To determine the air quality impact of MTBE, measurements were made of ambient MTBE and other gasoline constituents at a service station. Additionally, environmental conditions (wind speed, wind direction, and temperature, etc.) that could affect concentrations of emission constituents were measured. Gas samples were analyzed for target MTBE and volatile organic compounds, e.g., benzene and toluene. Ambient samples were collected using Tenax adsorbent tubes for mass spectrometric analysis at a service station located in Changhua County, Taiwan. The resulting measured ambient air concentrations were compared with Taiwans regulatory standards for hazardous air pollutants. Subsequently, the factors controlling the formation of high-VOC levels at the service station and in the residential neighborhoods were identified. Additionally, the results can provide the Environmental Protection Agency (EPA) of Taiwan with useful information and prompt them to mandate this gas service station to install a refueling vapor recovery system.     

The adsorption of benzene and methylethylketone onto activated carbon: thermodynamic aspects.

The adsorption of volatile organic compounds (VOCs), exemplified by benzene and methylethylketone (MEK), onto seven different types of activated carbon was investigated. Results show that for benzene adsorption the adsorption characteristic energy, enthalpy, free energy and entropy are in the range 17.12-36.86, -20.8 to -44.7, -11.89 to -16.22 kJ/mole and -29.4 to -85.3 J/mole/K, respectively. For the adsorption of MEK, the adsorption characteristic energy, enthalpy, free energy and entropy are in the range 14.47-32.34, -18.3 to -40.8, -10.78 to -15.56 kJ/mole and -24.8 to approximately -60.3 J/mole/K, respectively. The adsorption enthalpy can be calculated indirectly from statistical thermodynamic method and directly from the immersion enthalpy method. The adsorption characteristic energy is calculated by the Dubinin-Astokhov equation. The free energy is calculated by the measured equilibrium adsorption constant.     

Anaerobic degradation of nonylphenol in soil

This study investigated the effects of various factors on the anaerobic degradation of nonylphenol (NP) in soil. The results show that the optimal pH for NP degradation was 7.0 and that the degradation rate was enhanced when the temperature was increased. The addition of compost enhanced NP degradation. The individual addition of the electron donors lactate, acetate, and pyruvate inhibited NP degradation. The high-to-low order of NP degradation rates under three anaerobic conditions was sulfate-reducing conditions > methanogenic conditions > nitrate-reducing conditions. The results show that sulfate-reducing bacteria, methanogen, and eubacteria are involved in the anaerobic degradation of NP, with sulfate-reducing bacteria being a major component of the soil. Of the anaerobic strains isolated from the soil samples, strain AT3 expressed the best ability to biodegrade NP.     

Reusing pretreated desulfurization slag to improve clinkerization and clinker grindability for energy conservation in cement manufacture

The purpose of this study was to combine the physical pretreatments of grinding, sieving, and magnetic-separation processes to reclaim iron-rich materials from the desulfurization slag, and to use the remainder for cement clinker production. The iron-rich materials can be separated out efficiently by grinding for 30 min and sieving with a 0.3 mm mesh. The non-magnetic fraction of the particles smaller than 0.3 mm was in the majority, and proved to be suitable for use as a cement raw material. The raw mixes prepared with a pretreated desulfurization slag had a relatively high reactivity, and the temperature at which alite forms was significantly reduced during the clinkerization process. The clinkers produced with 10% desulfurization slag had a high level of alite and good grindability. Generally, the improvements in clinkerization and clinker grindability are beneficial to energy conservation in cement manufacture.     

Microbial dechlorination of 2,4,6-trichlorophenol in anaerobic sewage sludge

The dechlorination of 2,4,6-trichlorophenol (TCP) in municipal sewage sludge with a chlorophenol (CP)-adapted consortium was investigated. Results show that dechlorination rates differed according to the source of the sludge samples used in the batch experiments. No significant differences in 2,4,6-TCP dechlorination were observed following treatment with inoculum at densities ranging from 10% to 50% (V/V), but a significant delay was noted at 5% (V/V) density. Overall, results show that the higher the 2,4,6-TCP concentration, the slower the dechlorination rate. The addition of acetate, lactate, pyruvate, vitamin B12 or manganese dioxide did not results in a significant change in 2,4,6-TCP dechlorination. Data collected from a bioreactor experiment revealed that pH 7.0 and a total solid concentration of 10 g/L were optimal for dechlorination. Dechlorination rates decreased significantly at higher agitation speeds. 2,4,6-TCP dechlorination was enhanced under methanogenic conditions, but it was inhibited under denitrifying and sulfate-reducing conditions.