Implications of urine-to-feces ratio in the thermophilic anaerobic digestion of swine waste.

Thermophilic anaerobic digestion of swine manure represents a potential waste treatment technology to address environmental concerns, such as odor emissions and removal of pathogenic microorganisms. However, there are concerns relative to the stability of this process when swine manure is the sole substrate. In this study, the potential of biogas production from swine manure as the sole substrate under thermophilic (50 degrees C) conditions was investigated in the laboratory, to determine whether separation of urine and feces as part of the waste collection process would benefit anaerobic digestion. Effluent from a continuously stirred tank reactor was used as the inoculum for batch tests, in which the substrate contained three different concentrations of urine (urine-free, as-excreted urine-to-feces ratio and double the as-excreted urine-to-feces ratio). Inocula were acclimated to these same urine-to-feces ratios to determine methane production. Results show that both urine-free and as-excreted substrates were not inhibitory to anaerobic inocula. Anaerobic microorganisms can be readily acclimated to substrate with double the as-excreted urine concentration, which contained nitrogen concentrations up to 7.20 g/L. Cumulative methane production reached similar levels in the batch tests, regardless of the substrate urine concentration.     

基于航空摄影测量的填埋堆体动态重构精度及影响因素

填埋堆体表面形变监测是填埋场库容管理和堆体失稳等风险分析的核心,其时空高分辨率监测研究近年来引起广泛关注。基于航空摄影的地表测量技术具有采集速度快、时空分辨率高等优点,但在填埋场特殊环境下,面对高频填埋活动、显著的堆体变化以及防雨膜覆盖等干扰时,要同时满足高时空分辨率和耗时短的动态监测要求,无人机的最佳飞行参数设定亟待研究。为此,该研究模拟中等规模危险废物填埋场的规模和日填埋量,利用专业级无人机获取模拟区域图像,空三加密处理生成三维点云数据,利用Arcmap叠加分析多期监测数据,从点位坐标、重构尺度、重构体积、体积差分精度4个角度分析重构误差。结果表明:三维重构的坐标精度可以达到米级;重构尺度误差为2~3 cm,重构体积误差为0.16~0.17 m³,差分体积误差为0.16~0.17 m³;进一步研究发现,高度为25~55 m时,高度越高精度越低,相机倾角为[-53°,-60°]时,精度最高,旁向重叠率大于80%时,误差骤减且基本稳定。考虑到填埋场的填埋作业间隔、无人机续航能力等对飞行时间的约束,为获得最佳精度,建议无人机飞行高度为37 m、相机倾斜角度为[-53°,-60°]、旁向重叠率为80%。     

Identification of soil heavy metal sources from anthropogenic activities and pollution assessment of Fuyang County, China

Understanding regional variations of soil heavy metals and their anthropogenic influence are very important for environmental planning. In this study, 286 surface soil samples were collected in Fuyang county, and the 'total' metals for copper (Cu), zinc (Zn), lead (Pb), cadmium (Cd) and nickel (Ni) were measured in 2005. Statistic analysis showed that Cu, Zn, Pb and Cd had been added by exterior factors, and Ni was mainly controlled by natural factors. The combination of multivariate statistical and geostatistical analysis successfully grouped three groups (Cu, Zn and Pb; Cd; and Ni) of heavy metals from different sources. Through pollution evaluation, it was found that 15.76% of the study area for Cu, Zn and Pb, and 46.14% for Cd suffered from moderate or severe pollution. Further spatial analysis identified the limestone mining activities, paper mills, cement factory and metallurgic activities were the main sources for the concentration of Cu, Zn, Pb and Cd in soils, and soil Ni was mainly determined by the parent materials.     

Characteristics of organic precursors and their relationship with disinfection by-products

The molecular weight distribution and chemical composition of precursors and their relationship with disinfection by-products (DBPs) were investigated. Most of the organic matter responsible for the major DBP precursors in the Pan-Hsin water are small compounds with a molecular weight less than 1 kDa. The hydrophobic acids display the greatest ability to produce DBP. Therefore, effective removal of small molecules or hydrophobic acidic organics prior to disinfection process will significantly reduce the DBP concentration in the finished water. Although the coagulation process is effective in removing large organic precursors and the removal efficiencies of CHCl3 formation potential and organic carbon increase proportionally to the molecular weight of the precursors, the conventional treatment methods have limited efficiency in eliminating small precursors, which have high DBP formation potential.     

Nitrogen export from an agriculture watershed in the Taihu Lake area, China

Temporal changes in nitrogen concentrations and stream discharge, as well as sediment and nitrogen losses from erosion plots with different land uses, were studied in an agricultural watershed in the Taihu Lake area in eastern China. The highest overland runoff loads and nitrogen losses were measured under the upland at a convergent footslope. Much higher runoff, sediment and nitrogen losses were observed under upland cropping and vegetable fields than that under chestnut orchard and bamboo forest. Sediment associated nitrogen losses accounted for 8-43.5% of total nitrogen export via overland runoff. N lost in dissolved inorganic nitrogen forms (NO(3-)-N + NH4+-N) accounted for less than 50% of total water associated nitrogen export. Agricultural practices and weather-driven fluctuation in discharge were main reasons for the temporal variations in nutrient losses via stream discharge. Significant correlation between the total nitrogen concentration and stream discharge load was observed. Simple regression models could give satisfactory results for prediction of the total nitrogen concentrations in stream water and can be used for better quantifying nitrogen losses from arable land. Nitrogen losses from the studied watershed via stream discharge during rice season in the year 2002 were estimated to be 10.5 kg N/ha using these simple models.     

施肥对稻田甲烷与氧化亚氮排放的影响

大气温室气体浓度的升高引起太阳辐射加强,导致全球变暖已成为不争的事实。农田是温室气体排放的重要来源之一,采用静态箱-气相色谱法探讨不同氮肥类型与施氮水平对华南稻田甲烷（CH4）与氧化亚氮（N2O）排放的影响。试验共设置5个处理,每处理3次重复,分别（以N计）为U6（90 kg·hm-2）,U10（150 kg·hm-2）,U12（180 kg·hm-2）,SR10（150 kg·hm-2,缓释肥）,CR10（150 kg·hm-2,控释肥）。各处理磷钾肥用量一致,分别为45 kg·hm-2（以P2O5计）和127.5 kg·hm-2（以K2O计）。研究结果表明：稻田CH4与N2O排放量随氮肥用量的增加呈增加趋势。晚稻CH4排放呈单峰型,其峰值出现在水稻移栽后16~23 d,N2O排放并未出现明显的排放峰。CH4累积排放主要发生在返青-分蘖初期和分蘖盛期-幼穗分化期两个时段,而N2O的累积排放主要集中在灌浆-成熟期（U6处理除外）。不同氮肥类型处理CH4季节排放总量与平均排放量表现为：处理SR10〉处理U10〉处理CR10,其中,控释肥处理甲烷排放总量较常规尿素处理减少了11.3%;而N2O季节排放总量与平均排放量表现为：处理CR10〉处理U10〉处理SR10。综上,初步认为氮肥的施用能够促进CH4与N2O的释放,缓释肥处理能有效减少稻田N2O的排放,而控释尿素处理能明显降低稻田CH4气体的排放,且稻田CH4与N2O的排放存在一定的互为消长关系,因此如何平衡稻田甲烷与氧化亚氮释放,使稻田增温潜势最小化是下一步研究的重点和方向。     

Residues of PCDD,PCDF, and PCBs in some marine organisms in Lake Temsah,Ismailia, Egypt

Residues of PCDDs/F, non-ortho, mono-ortho PCBs, and other PCBs were monitored in the tissues of mullet fish, bolti fish, bivalves and crab taken from Lake Temsah, at Ismailia, Egypt.

Results showed that 2,3,7,8 Tetra CDD and 1,2,3,7,8 Penta CDD were the most frequently detected PCDD congeners. Similarly, 2,3,7,8 Tetra CDF, 1,2,3,7,8 Penta CDF and 2,3,4,7,8 Penta CDF were the most frequently detected PCDF congeners. No relationship was apparent between the concentrations of detected PCDDs congeners and the degree of chlorination, except with crab samples in which an increase in the chlorination coincided with a decrease in the concentrations of the congeners.

In PCDF congeners, detected residues have had a reversed relationship with chlorination increase. In PCDD congeners, Octa CDD had the highest detected concentrations in the two fish species, while in the bivalves and crab, 2,3,7,8 Tetra CDD had the highest concentrations. The mullet fish had the highest total PCDDs concentration, at 0.398?pg/g fresh weight, followed by crab at 0.395?pg/g fresh weight, then bivalves and bolti fish at 0.187 and 0.062?pg/g fresh weight, respectively. In all the examined organisms, the total concentrations of PCDFs were much higher than the total concentrations of the PCDD congeners. The WHO–TEQ values were 11.92, 39.12, 25, and 3.6?pg/g fresh weight, for mullet fish, bolti fish, bivlaves and crab, respectively. The concentration of the mono-ortho congeners CB 118 was the highest detected of all non-ortho and mono-ortho PCBs congeners, with values of 0.382, 0.022, 0.231 and 0.357?ng/g fresh weight, in mullet fish, bolti fish, bivalves and crab, respectively. The WHO–TEQ concentrations were 0.799, 0.003?pg/g fw, 0.05?pg/g fresh weight, 0.676?pg/g, and 0.799?pg/g fresh weight, for the same species, respectively. The total concentration of PCBs 28, 52, 95, 99, 101, 105, 110, 118, 138, 146, 149, 151, 153, 170, 177, 180, 187 were 6.86?ng/g fresh weight for mullet fish, 0.2?ng/g fresh weight, for bolti fish, 2.72?ng/g fresh weight for bivalves and 2.8?ng/g fresh weight for crab, respectively.     

Biodegradation of phthalate esters by two bacteria strains

In this study two aerobic phthalic acid ester (PAE) degrading bacteria strains, DK4 and O18, were isolated from river sediment and petrochemical sludge, respectively. The two strains were found to rapidly degrade PAE with shorter alkyl-chains such diethyl phthalate (DEP), dipropyl phthalate (DPrP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP) and diphenyl phthalate (DPP) are very easily biodegraded, while PAE with longer alkyl-chains such as dicyclohexyl phthalate (DCP) and dihexyl phthalate (DHP) and di-(2-ethylhexyl) phthalate (DEHP) are poorly degraded. The degradation rates of the eight PAEs were higher for strain DK4 than for strain O18. In the simultaneous presence of strains DK4 and O18, the degradation rates of the eight PAEs examined were enhanced. When the eight PAEs were present simultaneously, degradation rates were also enhanced. We also found that PAE degradation was delayed by the addition of nonylphenol or selected polycyclic aromatic hydrocarbons (PAHs) at a concentration of 1 microg/g in the sediment. The bacteria strains isolated, DK4 and O18, were identified as Sphigomonas sp. and Corynebacterium sp., respectively.     

Rapid degradation of butachlor in wheat rhizosphere soil

The degradative characteristics of butachlor in non-rhizosphere, wheat rhizosphere, and inoculated rhizosphere soils were measured. The rate constants for the degradation of butachlor in non-rhizosphere, rhizosphere, and inoculated rhizosphere soils were measured to be 0.0385, 0.0902, 0.1091 at 1 mg/kg, 0.0348, 0.0629, 0.2355 at 10 mg/kg, and 0.0299, 0.0386, 0.0642 at 100 mg/kg, respectively. The corresponding half-lives for butachlor in the soils were calculated to be 18.0, 7.7, 6.3 days at 1 mg/kg, 19.9, 11.0, 2.9 days at 10 mg/kg, and 23.2, 18.0, 10.8 days at 100 mg/kg, respectively. The experimental results show that the degradation of butachlor can be enhanced greatly in wheat rhizosphere, and especially in the rhizosphere inoculated with the bacterial community designated HD which is capable of degrading butachlor. It could be concluded that rhizosphere soil inoculated with microorganisms-degrading target herbicides is a useful pathway to achieve rapid degradation of the herbicides in soil.     

PAH and soot emissions from burning components of medical waste: examination/surgical gloves and cotton pads

This is a laboratory investigation on the emissions from batch combustion of representative infectious ("red bag") medical waste components, such as medical examination latex gloves and sterile cotton pads. Plastics and cloth account for the majority of the red bag wastes by mass and, certainly, by volume. An electrically heated, horizontal muffle furnace was used for batch combustion of small quantities of shredded fuels (0.5-1.5 g) at a gas temperature of approximately 1000 degrees C. The residence time of the post-combustion gases in the furnace was approximately 1 s. At the exit of the furnace, the following emissions were measured: CO, CO2, NOx, particulates and polynuclear aromatic compounds (PACs). The first three gaseous emissions were measured with continuous gas analyzers. Soot and PAC emissions were simultaneously measured by passing the furnace effluent through a filter (to collect condensed-phase PACs) and a bed of XAD-4 adsorbent (to capture gaseous-phase PACs). Analysis involved soxhlet extraction, followed by gas chromatography-mass spectrometry (GC-MS). Results were contrasted with previously measured emissions from batch combustion of pulverized coal and tire-derived fuel (TDF) under similar conditions. Results showed that the particulate soot) and cumulative PAC emissions from batch combustion of latex gloves were more than an order of magnitude higher than those from cotton pads. The following values are indicative of the relative trends (but not necessarily absolute values) in emission yields: 26% of the mass of the latex was converted to soot, 11% of which was condensed PAC. Only 2% of the mass of cotton pads was converted to soot, and only 3% of the weight of that soot was condensed PAC. The PAC yields from latex were comparable to those from TDF. The PAC yields from cotton were higher than those from coal. A notable exception to this trend was that the three-ring gas-phase PAC yields from cotton were more significant than those from latex. Emission yields of CO and CO2 from batch combustion of cotton were, respectively, comparable and higher than those from latex, despite the fact that the carbon content of cotton was half that of latex. This is indicative of the more effective combustion of cotton. Nearly all of the mass of carbon of cotton gasified to CO and CO2 while only small fractions of the carbon in latex were converted to CO2 and CO (20% and 10%, respectively). Yields of NOx from batch combustions of latex and cotton accounted for 15% and 12%, respectively, of the mass of fuel nitrogen indicating that more fuel nitrogen was converted to NOx in the former case, possibly due to higher flame temperatures. No SO2 emissions were detected, indicating that during the fuel-rich combustion of latex, its sulfur content was converted to other compounds (such as H2S) or remained in the soot.