Coastal spreading of olivine to control atmospheric CO2 concentrations: A critical analysis of viability

Qualitative proposals to control atmospheric CO₂ concentrations by spreading crushed olivine rock along the Earth's coastlines, thereby accelerating weathering reactions, are presently attracting considerable attention. This paper provides a critical evaluation of the concept, demonstrating quantitatively whether or not it can contribute significantly to CO₂ sequestration. The feasibility of the concept depends on the rate of olivine dissolution, the sequestration capacity of the dominant reaction, and its CO₂ footprint. Kinetics calculations show that offsetting 30% of worldwide 1990 CO₂ emissions by beach weathering means distributing of 5.0 Gt of olivine per year. For mean seawater temperatures of 15–25 °C, olivine sand (300 μm grain size) takes 700–2100 years to reach the necessary steady state sequestration rate and is therefore of little practical value. To obtain useful, steady state CO₂ uptake rates within 15–20 years requires grain sizes <10 μm. However, the preparation and movement of the required material poses major economic, infrastructural and public health questions. We conclude that coastal spreading of olivine is not a viable method of CO₂ sequestration on the scale needed. The method certainly cannot replace CCS technologies as a means of controlling atmospheric CO₂ concentrations.     

De-novo formation of dioxins and furans and the memory effect in waste incineration flue gases

The formation of dioxin (polychlorinated-rho-dibenzodioxins - PCDD) and furan (polychlorinated dibenzofurans - PCDF) in waste incineration flyash in relation to temperature has been investigated in a bench scale reactor. The PCDD/PCDF released into the exhaust gases of the reactor and trapped in a condensation and vapour phase adsorption system were also determined. The concentrations of PCDD/PCDF in the flyash were analysed in detail for all congeners and isomers including the mono-, di- and tri-PCDD/PCDF. De-novo synthesis of PCDD/PCDF was clearly seen in the flyash with large changes in concentrations of PCDD/PCDF with only small changes in temperature. Exhaust gas PCDD/PCDF were detected at all temperatures, with the maximum emission occurring at a flyash temperature of 350 degrees C, where the equivalent of over 42 times the total dioxin/furan concentration of the original flyash was lost to the vapour phase per unit mass of initial flyash. Although the desorbed species were mainly the lower mono- to tri-congener group of dioxins and furans, the desorbed dioxin/furans had a considerable toxic equivalent value.     

The effects of aeration rate on generated compost quality, using aerated static pile method

To determine the most appropriate composting process in an active municipal solid waste system, an experiment was carried out using a nested design method with three aeration rates. During each aeration rate, parameters such as temperature, pH, EC, carbon-to-nitrogen ratio, NO(3)-N, nitrogen, potassium and phosphorous were measured and the efficiency of different composting processes was evaluated. The result of this study showed that the lower and medium aeration rates had a significant impact on nitrogen, carbon-to-nitrogen ratio and temperature profile, while higher aeration rates led to higher EC values. Furthermore, the thermophilic phase lasted 13, 9 and 4 weeks for the aeration rates of 0.4, 0.6 and 0.9 L min(-1)kg(-1), respectively. Accordingly, it was concluded that starting at a rate of 0.6 L min(-1)kg(-1) during first 2 months (about 9 weeks) of the process and continuing at a rate of 0.4 L min(-1)kg(-1)until the end of composting process would result in lower energy consumption.     

Aging and compressibility of municipal solid wastes

The expansion of a municipal solid waste (MSW) landfill requires the ability to predict settlement behavior of the existing landfill. The practice of using a single compressibility value when performing a settlement analysis may lead to inaccurate predictions. This paper gives consideration to changes in the mechanical compressibility of MSW as a function of the fill age of MSW as well as the embedding depth of MSW. Borehole samples representative of various fill ages were obtained from five boreholes drilled to the bottom of the Qizhishan landfill in Suzhou, China. Thirty-one borehole samples were used to perform confined compression tests. Waste composition and volume-mass properties (i.e., unit weight, void ratio, and water content) were measured on all the samples. The test results showed that the compressible components of the MSW (i.e., organics, plastics, paper, wood and textiles) decreased with an increase in the fill age. The in situ void ratio of the MSW was shown to decrease with depth into the landfill. The compression index, Cc, was observed to decrease from 1.0 to 0.3 with depth into the landfill. Settlement analyses were performed on the existing landfill, demonstrating that the variation of MSW compressibility with fill age or depth should be taken into account in the settlement prediction.     

Natural Weathering Studies of Polypropylene

Polypropylene (PP) has achieved a dominating position and hence, their consumption increases thereby littering, which lead to environmental pollution. Photodegradation seems to be a better choice because of naturally available sunlight as energy source for degradation. The present work involves the study of the variation of degradation behavior of PP film during tropical summer and winter seasons. The photodegradation is followed by Fourier transform infrared (FTIR) spectroscopic technique. Various indices like hydroxyl, carbonyl, vinylidene, lactones, ester, carboxylic acid and crystallinity are calculated and these values increased after a brief induction period. The variation in the mechanical properties like tensile strength and elongation at break percentages are determined. The scanning electron microscopic (SEM) images of weathered PP showed surface cracks when carbonyl index value increases sharply and the mechanical properties show a sudden decrease. Attempted life time prediction using mathematical models showed that the carbonyl growth is more affected by ultraviolet (UV) and cumulative total solar radiation for PP weathered during summer. The loss in tensile strength of PP weathered during summer is more dependent on the average temperature and the UV portion of the total solar radiation whereas, intensity of UV radiation has profound effect on the tensile strength of PP weathered during winter.     

A Novel Method to Capture and Analyze Flow in a Gross Pollutant Trap Using Image-Based Vector Visualization

A novel method is developed to capture and analyze several experimental flow regimes through a gross pollutant trap (GPT) with fully and partially blocked screens. Typical flow conditions and screen blockages are based on findings from field investigations that show a high content of organic matter in urban areas. Fluid motion of neutral buoyant particles is tracked using a high-speed camera and particle image velocimetry (PIV) software. The recorded fluid motion is visualized through an image-based, line integral convolution (LIC) algorithm, generally suitable for large computational fluid dynamics (CFD) datasets. The LIC method, a dense representation of streamlines, is found to be superior to the point-based flow visualization (e.g., hedgehog or arrow plots) in highlighting main flow features that are important for understanding litter capture and retention in the GPT. Detailed comparisons are made between the flow regimes, and the results are compared with CFD data previously obtained for fully blocked screens. The LIC technique is a useful tool for identifying flow structures in the GPT and areas that are subjected to abnormalities difficult to detect by conventional methods. The novel method is found to be useful both in the laboratory and in the field, with little preparation and cost. The enhancements and pitfalls of the LIC technique along with the experimentally captured flow field are presented and discussed.     

The Effect of Masterbatch Addition on the Mechanical, Thermal, Optical and Surface Properties of Poly(lactic acid)

There has been considerable interest in the use of the biodegradable polymer poly(lactic acid) (PLA) as a replacement for petroleum derived polymers due to ease of processability and its high mechanical strength. Other material properties have however limited its wider application. These include its brittle properties, low impact strength and yellow tint. In an attempt to overcome these drawbacks, PLA was blended with four commercially available additives, commonly known as masterbatches. The effect of the addition of 1.5 wt% of the four masterbatches on the mechanical, thermal, optical and surface properties of the polymer was evaluated. All four masterbatches had a slight negative effect on the tensile strength of PLA (3–5% reduction). There was a four fold increase in impact resistance however with the addition of one of the masterbatches. Differential scanning calorimetry demonstrated that this increase corresponded to a decrease in the polymer crystallinity. However there was an associated increase in polymer haze with the addition of this masterbatch. The clarity of PLA was improved through the addition of an optical brightener masterbatch, but the impact resistance remained low. The glass transition and melting temperatures of PLA were not affected by the addition of the masterbatches, and no change was observed in surface energy. Some delay in PLA degradation, in a PBS degradation medium at 50 °C, was observed due to blending with these masterbatches.     

Valuing lives equally in a benefit-coast analysis of safety projects: A method to reconcile theory and practice

A value of statistical life (VSL) is used in cost-benefit analysis (CBA) as a monetary measure of the benefits to people from small risk reductions that arise from safety projects. Despite its widespread use in a number of countries, the concept of a VSL remains controversial, not least because it implies acceptance of the underlying ethical assumptions of CBA together with the idea that ‘social welfare’ can be measured and aggregated in some manner. In addition, to comply with theory, variable VSLs for different groups within society would be advocated. However, without fail, empirically, it is the case that those countries that employ a willingness to pay based approach to cost-benefit analysis of a safety project appraisal tend to use a single value for that accident context that is independent of the per capita income level, or indeed other personal characteristics, of the sub-group in society to which the safety improvement will actually apply. This article presents a straightforward, but theoretically justified adaptation to the calculation of a VSL which allows empirical practice by policymakers i.e. the application of a “common” VSL for any particular hazard within a given society, to be compatible with a CBA decision making approach.     

A method for ranking components importance in presence of epistemic uncertainties

Importance Measures (IMs) are used to rank the contributions of components or basic events to the system performance, e.g. its reliability or risk. Most times, IMs are calculated without due account of the uncertainties in the model of the behavior of the system. The objective of this work is to investigate how uncertainties can influence IMs and to develop a method for giving them due account in the corresponding ranking of the components or basic events. The uncertainties considered in this work affect the model parameters values and are assumed to be described by probability density functions. The method for ranking the contributors to the system performance measure is applied to the auxiliary feedwater system of a nuclear pressurized water reactor.     

Nanofiltration of concentrated and salted tuna cooking juices

Tuna cooking juice from a Tunisian tuna-processing unit has a high level of polluting load: chemical oxygen demand (COD) is comprised between 4 and 20 g L⁻¹, nitrogen kjedahl (NK) between 0.6 and 3 g L⁻¹ and dry matter between 120 and 160 g L⁻¹. The juice has thus to be treated before being rejected into the environment. This paper considers the nanofiltration (NF) of these concentrated organic/inorganic mixtures using an AFC 30 (NF) membrane. The work focusses on the effect of organic and inorganic matters on the permeate flux and rejections of these matters. For this purpose, mixtures of salt and organic pollution (COD), used as model solutions, were prepared by the dilution of a typical industrial tuna cooking juice. The permeate flux was found to decrease when salt and organic matter concentrations increase. The recovery rate in organic matter decreases with increasing salt or organic matter content and the recovery rate of salt decreases when the COD concentration increases.