Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

Life cycle assessment of biodiesel fuel production from waste cooking oil in Okayama City

A life cycle assessment (LCA) is performed to make clear of the actual environment impacts from conversation of waste cooking oil (WCO) to biodiesel fuel (BDF) in Okayama. A scenario analysis is carried out based on different participation rate of residents who separate WCO from general waste, corresponding to different BDF utilisation rate in transportation system. Sub scenarios complying with different gas emission standards regarding vehicles are designed as well. Afterwards, life cycle impact assessment is conducted to focus on global warming, acidification, and urban air pollution. Overall improvement of almost all kinds of life cycle inventories is significant when diesel is replaced with BDF, demonstrating that a shift from WCO-to-incineration to WCO-to-BDF is more beneficial. Under carbon neutral, compared to base scenario (S0), about 746.05 ton CO₂ emission will be reduced annually in the scenario with 100 % BDF utilisation in vehicles (S4). Meanwhile, total external cost in three environmental impacts (EI) sharply reduces by 51.90 %, showing much economic sustainability in S4. Moreover, the manufacturing cost for producing one litter WCO-to-BDF is 97.32 Yen. Sensitivity analysis shows that the gas emission standard regarding vehicles had much bigger effect on EI than BDF manufacturing process in this research.     

Municipal solid waste composition and food loss reduction in Kyoto City

For 35 years, Kyoto City has conducted detailed household waste composition surveys under the guidance of Kyoto University by dividing household waste into approximately 400 categories. In addition, the city has conducted detailed composition surveys of commercial waste generated by businesses. These surveys show that food loss accounts for approximately 40% of total waste, of which leftovers and untouched food account for about 40% in both households and business facilities. Consequently, the annual generation of household and commercial food loss is estimated at about 30,000 tons. Various efforts have been made to reduce waste, including food loss, but further reduction in environmental burden is needed. Thus, Kyoto City revised the ordinance for waste reduction, and in March 2015, formulated a new municipal waste management plan. The plan not only includes the 2Rs (reduce, reuse), but also, for the first time in Japan, sets quantitative targets for reducing food loss. Kyoto City must ensure that the necessary waste reduction measures are clearly explained to the residents and business operators. To ensure that this plan is successful, it is important to clarify concrete actions that residents and business operators should implement, along with their effects.     

Rare earth element recovery potentials from end-of-life hybrid electric vehicle components in 2010–2030

Increasing attention is currently given to the management of end-of-life (EoL) hybrid electric vehicles (HEVs), because approximately two decades have passed since they were first introduced to the market. A HEV would be one of the largest consumers of rare earth elements (REEs), and hence represents the greatest potential for REE recovery in the future. The purpose of this study is to clarify the present and future recovery potential of REEs that are disposed of as EoL HEVs. This study first estimated the numbers of EoL HEVs during fiscal years (FYs) 2010–2030, and then clarified the potential for recovery of REEs from two HEV-specific components—the hybrid transmission and NiMH battery unit. The results suggest that 0.51–0.65 million HEVs will reach the EoL stage in FY2030, compared with only 11,000 HEVs in FY2010. As of FY2030, REE recovery potentials will increase to 220 tons and 2900 tons for EoL hybrid transmission and NiMH battery units, respectively. A total of 49,000 tons of REEs will be contained within HEV-specific components of HEVs still in use. Moreover, the potential for recovery of REEs from EoL hybrid transmissions and NiMH battery units is estimated to equal 35.4 and 92.1 % of respective demand.     

Energy recovery and greenhouse gas reduction potential from food waste in Japan

Waste-to-energy is one effective waste management approach for a sustainable society. The purpose of this study was to clarify the potential for energy recovery and greenhouse gas (GHG) reduction that could be achieved by introducing anaerobic digestion (AD) facilities in the process of reconstructing aging incineration facilities in Japan. Using statistical data from 1068 incineration facilities, four future scenarios were considered and compared with the current situation. As results, compared with the current situation the amount of electricity generated could increase by 60 % in 2030, by combining AD facilities for food waste with new, high-efficiency incineration facilities for remaining municipal solid waste (MSW). From a life cycle perspective, net energy recovery in 2030 was approximately three times greater than in 2011, and GHG emission could be reduced by 27 %. The introduction of AD facilities is attractive for small authorities, which currently treat <100 t/day of MSW through incineration facilities without energy recovery. An AD facility is also beneficial for large authorities. On the contrary, in middle-scale authorities that treat 100–299 t/day of MSW, the reconstruction of incineration facilities to include electricity production capabilities requires careful consideration, because it will significantly influence energy recovery and GHG reduction effects.     

Development of a technique for the measurement of the radon exhalation rate using an activated charcoal collector

A simple system to evaluate the 222Rn (radon) exhalation rate from soil has been improved. A sampling cuvette of 2.1 L is placed so that it covers the targeted ground soil, and radon emanating from the soil accumulates within the cuvette for 24 h. Its internal radon concentration is measured by the combination of an activated charcoal (PICO-RAD) and a liquid scintillation counting system. This study shows variations of the conversion factor (CF: unit Bq m(-3)/cpm) of PICO-RAD. The range of CF due to temperature (10-30 degrees C) was between -21% and +69%, and this due to humidity (30-90%) was between 0% and -15%. Humidity and radon concentration in the cuvette covering soil tended to saturate in a few hours. The above information was used to correct the CF for the evaluation. The improved system shows high reliability and can be easily applied to natural environments.     

Manufacture of strand board made from construction scrap wood

The objective of this research was to evaluate the physical and mechanical properties of strand board made from construction scrap wood. The strand board was manufactured using Sugi (Cryptomeria japonica D. Don) and Douglas-fir (Pseudotsuga japonica) strands selected from construction scrap wood. The strands were oriented, and three-layer (face/core/face) strand board of three types was produced: one in which the strands of the face layer were oriented at a right angle to those of the core layer (R board), another in which the strands of the face layer were oriented parallel to those of the core layer (P board), and a third in which the strands of both layers were oriented at random (Ra board). The physical and mechanical properties of the boards were evaluated based on Japanese Industrial Standard (JIS). The main results obtained are as follows: the bending strength of the strand board with a density larger than 0.55 g/cm³ exceeded the standard value of type 18 particleboard of JIS A 5908. The bending strength of the strand board was affected by board density, strand orientation and resin content, and became larger with increased density as well as resin content. That of the parallel specimen of P board was the largest among the specimen-orientations and types. The internal bond strength of the strand board with a density larger than 0.55 g/cm³ exceeded the standard value of type 18 particleboard and type 24-10 particleboard of JIS A 5908. The internal bond strength was markedly affected by the resin content of the core layer, and became larger with increased density. The thickness swelling of the strand board decreased with increased resin content, and become larger with increased density.     

Identification and estrogenic characterization of impurities in commercial bisphenol A diglycidyl ether (BADGE)

A sample of commercial BADGE was fractioned by HPLC and eight impurities including novel propyl derivatives (2), (5) and (6) were identified by NMR spectrometry, FAB-MS and GC-MS. The estrogenicity, both agonist and antagonist, of fractions containing these impurities was measured with a yeast two-hybrid assay incorporating the human (hER alpha) and a competitive binding assay for hER alpha (ELISA). In the yeast two-hybrid assay, estrogenic antagonist activity was found in two fractions, while estrogenic agonist activity was not found in any. In the ELISA method, the binding affinity to hER alpha was found in three fractions. It is probable that a comprehensive assessment of the estrogenic properties of commercial BADGE, and their implications for human health, will require examination of all its components as described here.     

Photodegradation of tetraphenyltin contained in polychlorinated biphenyl-based transformer oil simulants in alkaline 2-propanol solution

The photodegradation of tetraphenyltin (TePT) contained in polychlorinated biphenyl (PCB)-based transformer oil simulants by ultraviolet (UV) irradiation in alkaline 2-propanol solutions was examined. In the absence of PCBs, the TePT level fell to below 1% of the initial concentration within 30 min. In the absence of both PCBs and an alkali, the concentrations of tri-, di-, and monophenyltins initially increased to a few milligrams per liter, and then reduced to below the detection limits within 90 min. The addition of an alkali to the reaction solution slightly accelerated the photodecomposition of TePT. The decomposition of other phenyltins (PTs) was also accelerated. When PCBs with concentrations of approximately 80 times the initial TePT concentration were added, only a small fraction of the TePT decomposed within 100 min. Moreover, the levels of PTs did not change during irradiation. TePT and other PTs did decompose when the level of PCBs was reduced to the same concentration as that of TePT; however, the decomposition rates were slower than those in the absence of PCBs. In the actual treatment process, TePT and other PTs in PCB-based transformer oil are decomposed by catalytic reduction, which is used after UV irradiation. Therefore, in the actual treatment of PCB-based transformer oil wastes, pollution due to PTs can be prevented.