Toxicity of leather tanning wastewater effluents in sea urchin early development and in marine microalgae

This study was designed to investigate the composition and the toxicity of leather tanning wastewater and conditioned sludge collected at the leather tanning wastewater treatment plant (CODISO) located in Solofra, Avellino (Southern Italy). Samples were analyzed for their conventional parameters (COD, TSS, chromium and ammonia) and for metal content. Effluent samples included raw wastewater, and samples collected following coagulation/flocculation process and biological treatment. A set of toxicity endpoints were tested using sea urchin and marine microalgal bioassays by evaluating acute embryotoxicity, developmental defects, changes in sperm fertilization success and transmissible damage from sperm to the offspring, and changes in algal growth rate. Dose-related toxicity to sea urchin embryogenesis and sperm fertilization success was exerted by effluent or sludge samples according to the following rank: conditioned sludge > coagulated effluent > or = raw influent > effluent from biological treatment. Offspring quality was not affected by sperm exposure to any wastewater or to sludge samples. Algal growth was inhibited by raw or coagulated effluent to a similar extent and, again, the effluent from the biological treatment resulted in a decreased toxicity. The results suggest that coagulated effluent and conditioned sludge result in higher toxicity than raw influent in sea urchin embryos and sperm, whereas the biological wastewater treatment of coagulated effluent, in both sea urchins and algae, cause a substantial improvement of wastewater quality. Hence a final biological wastewater treatment should be operated to minimize any environmental damage from tannery wastewater.     

Speciation of inorganic arsenic in alimentary and environmental aqueous samples by using derivative anodic stripping chronopotentiometry (dASCP)

The purpose of this research was to develop a sensitive and accurate chronopotentiometric method at a gold film electrode, to determine trace and ultra trace levels of As(III) and As(V) in alimentary and environmental water systems. As(III) was directly determined in the aqueous matrix at a deposition potential of -300 mV for 180 s and at a constant anodic current of 2.5 microA, without any sample pre-treatment; moreover the chronopotentiometric method did not require a time-consuming de-oxygenation step prior to the analysis. A 3M HCl solution was chosen as the best stripping medium. The direct analysis of As(V) required the application of a high negative over-potential and, thus, measurements were characterized by poor reproducibility; therefore As(V) was determined after reduction to As(III) with KI in a strong hydrochloric acid solution. Under the optimised electrochemical conditions, detection limits of 0.08 microg As(III) l(-1) were achieved and no significant interferences from Cd, Cu, Pb, Zn and organic substances were observed. As(V) was the most abundant species in all the studied environmental and alimentary aqueous matrices. Amongst the beverages, tea and coffee presented the As(V) highest concentration ranges (934-1740 microg l(-1) and 850-1290 microg l(-1), respectively) while bottled mineral water the lowest (<1.61 microg l(-1)); whereas As(III) levels lower than 5.0 microg l(-1) were detected only in wine samples.     

Engineering and environmental properties of thermally treated mixtures containing MSWI fly ash and low-cost additives

An experimental work was carried out to investigate the feasibility of application of a sintering process to mixtures composed of Municipal Solid Waste Incinerator (MSWI) fly ash and low-cost additives (waste from feldspar production and cullet). The proportions of the three constituents were varied to adjust the mixture compositions to within the optimal range for sintering. The material was compacted in cylindrical specimens and treated at 1100 and 1150 degrees C for 30 and 60 min. Engineering and environmental characteristics including weight loss, dimensional changes, density, open porosity, mechanical strength, chemical stability and leaching behavior were determined for the treated material, allowing the relationship between the degree of sintering and both mixture composition and treatment conditions to be singled out. Mineralogical analyses detected the presence of neo-formation minerals from the pyroxene group. Estimation of the extent of metal loss from the samples indicated that the potential for volatilization of species of Pb, Cd and Zn is still a matter of major concern when dealing with thermal treatment of incinerator ash.     

A comparison of swine wastewater treatment using real-time and fixed-time two-stage sequencing batch reactors

This study compared the swine wastewater treatment of two identical lab-scale two-stage sequencing batch reactors (TSSBR) under similar conditions except that one was operated on a fixed-time mode and the other on a real-time mode. While both TSSBR systems performed very well, the real-time TSSBR performed far better then the fixed-time TSSBR, in every aspect of carbon, nitrogen, and phosphorous removal. The removals of COD, TOC, were at 97% and for BOD5 even at 99.7%. In terms of NH4-N and TKN removals, the real-time TSSBR achieved removal of over 98%. For phosphorus removals (Ortho-P and total P) the results from the real-time TSSBR was quite remarkable at 97.7%.     

Degradation of aqueous carbon tetrachloride by nanoscale zerovalent copper on a cation resin

Nanoscale zerovalent copper supported on a cation resin was successfully synthesized to enhance the removal of carbon tetrachloride (CCl(4)) from contaminated water. The use of the cation resin as a support prevents the reduction of surface area due to agglomeration of nanoscale zerovalent copper particles. Moreover, the cation resin recycles the copper ions resulting from the reaction between CCl(4) and Cu(0) by simultaneous ion exchange. The decline in the amount of CCl(4) in aqueous solution results from the combined effects of degradation by nanoscale zerovalent copper and sorption by the cation resin; thus the amount of CCl(4) both in aqueous solution and sorbed onto the resin were measured. The pseudo-first-order rate constant normalized by the surface-area and the mass concentration of nanoscale zerovalent copper (k(SA)) was 2.1+/-0.1 x 10(-2)lh(-1)m(-2), approximately twenty times that of commercial powdered zerovalent copper (0.04 mm). Due to the exchange between Cu(2+) and the strongly acidic ions (H(+) or Na(+)), the pH was between 3 and 4 in unbuffered solution and Cu(2+) at the concentration of less than 0.1 mg l(-1) was measured after the dechlorination reaction. In the above-ground application, resin as a support would facilitate the development of a process that could be designed for convenient emplacement and regeneration of porous reductive medium.     

Benefits of sustainable waste management in the vegetable greenhouse industry

This study investigated the benefits of an on-site sustainable solid waste treatment and utilization system for the greenhouse industry. The composts made from greenhouse wastes were tested and found to contain high nutrient values and good physical properties, and could be used as high quality growing media. The finished composts were tested in a greenhouse against the conventional growth media (sawdust) and resulted in a 10% yield increase by using the compost. An economic analysis was conducted to show the economic benefits of on-site composting for a greenhouse operation. Based on a four-hectare tomato or pepper greenhouse, and amortizing the capital equipment over five years, the net annual cost of composting represents a savings of dollars 8,000 annually.     

高层建筑火灾风险评估中一种具有置信度和方差的权系数

对评估中的权系数引入置信度和方差两个概念 ,为权系数提供更多的信息 ,便于决策者采用 ;针对作者在香港所作的高层建筑火灾风险因子评估系数 ,得到 16个风险因子的带置信度和方差的权系数 ,为火灾风险评估提供重要依据     

Bronchial Rn dose survey for residences

The bronchial dosimeter for Rn progeny proposed by Yu and Guan in 1998 was employed to survey the bronchial dose from Rn progeny in 30 residences in Hong Kong. An average bronchial deposition fraction of Rn progeny was obtained as 0.0334, which gave an average dose conversion factor (DCF) of 8.5 mSv WLM-1. The mean values of potential alpha energy concentration (PAEC) deposited in the tracheobronchial region (PAECT-B), total PAEC in air (PAECT), annual effective dose (E), concentration of Rn gas (RC) and annual dose conversion factor (ADCF) for all the residential sites combined were 0.11 +/- 0.05, 3.1 +/- 1.4 mWL, 1.2 +/- 0.5 mSv yr-1, 23 +/- 10 Bq m-3 and 0.055 +/- 0.020 (mSv yr-1 per Bqm-3), respectively, with air-conditioned sites (AC sites) and non-AC sites having significantly different mean ADCF values. The indoor relative humidity affected PAECT and RC with high confidence levels (> 95%).     

A geometric approach to determine adsorption and desorption kinetic constants

A geometric method based on Langmuir kinetics has been derived to determine adsorption and desorption kinetic constants. In the conventional procedure, either the adsorption kinetic constant (k(a)c) or desorption kinetic constant (k(d)c) is found from kinetic experiments and the other is calculated by their correlation with the equilibrium constant, i.e, k(d)c = Kcon/k(a)c, where Kcon has been known from equilibrium studies. The determined constants (Kcon, k(a)c, k(d)c), if based only on the conventional procedure, may not be accurate due to their mathematical dependence. Therefore, the objectives of this study are applying a geometric approach to directly determine Langmuir kinetic constants and describe adsorption behavior. In this approach, both adsorption kinetic constant (k(a)g) and desorption kinetic constant (k(d)g) are obtained only from data of kinetic experiments, and a geometric equilibrium constant (Kgeo) is calculated by Kgeo = k(a)g/k(d)g. The deviation between Kgeo and Kcon can prove the accuracy of k(a)g and k(d)g which were determined by this method. This approach was applicable to selenate, selenite and Mg2+ adsorption onto SiO2 regardless of whether the adsorbate formed inner- or outer-sphere complexes. However, this method showed some deviation between Kcon and Kgeo for Mn2+ adsorption because of the formation of surface Mn(II)-hydroxide clusters, which was inconsistent with the basic assumption of this method of monolayer adsorption.