高加速应力试验装置技术参数的测量

气锤驱动的高加速应力试验装置,能产生温度和非高斯随机振动应力,其中振动应力是由多个气锤作六自由度运动产生的。一般用来进行高温步进、低温步进、快速温度变化、振动、快速温变和振动复合试验。目前国家标准和校准规程中均无关于该试验装置的技术参数的校准方法。本文结合试验装置的技术特点,提出了几个关于温度和振动技术参数的测量方法,如:温度偏差、温度波动度、温度均匀度、温度过冲量、温度变化速率、均方根加速度、横向振动比、功率谱密度等。     

3种植物对Cd污染农田土壤的修复效果比较试验研究

通过盆栽试验研究了3种植物三叶鬼针草(Bidens pilosa L.)、紫茉莉(Mirabilis Jalapa)、中华景天(Sedum polytrich-oides)对上海地区2种质量浓度(1.2、12.0mg/kg)Cd污染农田土壤的修复效果,以探索其在上海地区Cd污染农田土壤修复中应用的可行性。结果表明:2种浓度下,三叶鬼针草对土壤Cd去除效果均最佳,1.2mg/kg处理下盆中土壤Cd质量浓度由原来的1.249 9mg/kg下降到0.861 7mg/kg,降低0.388 2mg/kg,Cd去除率为31.06%;12.0mg/kg处理下三叶鬼针草盆中土壤Cd质量浓度由原来的12.033 2mg/kg下降到10.020 6mg/kg,降低2.012 6mg/kg,Cd去除率为16.73%;紫茉莉和中华景天相比较而言,修复效果均较差。在2种浓度下,3种植物地上部分生物量排序均为三叶鬼针草>中华景天>紫茉莉。因此,建议将三叶鬼针草作为上海地区Cd污染农田土壤修复的优选植物。     

苦土和氧化镁处理氮磷废水的对比研究

分别采用苦土、纯氧化镁为沉淀剂对模拟高浓度氮磷废水(N/P=0.8)进行了脱氮除磷研究,比较了沉淀剂投加量、pH对2种沉淀剂处理氮磷废水的影响,对沉淀产物进行XRD分析,并进行了经济效益比较。结果表明,pH是影响2种沉淀剂处理氮磷废水的主要因素,随着pH的增加,脱氮除磷效果提高,在平衡pH为9～10之间时氮磷处理效果最佳,pH继续增加,由于磷酸镁沉淀的形成使得氨氮去除率降低。此外,处理相同的废水,苦土的最佳投加量要大于纯氧化镁,但是经济效益比较结果表明,以苦土为沉淀剂处理氮磷废水可大大降低处理成本。     

一体化臭氧-曝气生物滤池处理酸性玫瑰红印染模拟废水

针对含酸性玫瑰红印染废水高色度、难生物降解的特点,分别采用了一体化和分离式臭氧-曝气生物滤池(O3-BAF)工艺处理。与分离式工艺相比,一体化工艺的特点是在一个反应器内部同时实现臭氧氧化和生化的协同作用,降低了处理设施的基建和运行费用。实验结果表明,一体化工艺处理效果明显优于分离式工艺,脱色率达92%,COD去除率达60%,处理效果良好。     

UV-H_2O_2联用工艺去除水中阿特拉津的研究

采用间歇式反应器考察了UV-H2O2高级氧化技术去除水中阿特拉津的效果及其影响因素,并进行了相关的反应动力学研究。结果表明,在pH值6.9,阿特拉津初始浓度500μg/L,紫外辐照强度172μW/cm2时,H2O2投加量50mg/L,反应10min后,阿特拉津的去除率90%。UV-H2O2联用工艺对阿特拉津的降解符合一级反应动力学。H2O2在该联用工艺降解阿特拉津中具有双重作用,一方面,当H2O2投加量较小时,一级反应速率常数随H2O2投加量的增加基本呈现线性增加的趋势;另一方面,当H2O2浓度增加到一定程度(90mg/L)后,阿特拉津的降解速率随H2O2浓度的变化已不明显,而H2O2浓度为102mg/L时,则出现了抑制作用。     

接地极的土壤腐蚀

接地极是接地装置的主要组成部分,接地极埋设在土壤中,用于泄流,保障电网和电气设备的安全运行。近年来,接地极的腐蚀损坏造成的事故屡有发生,接地极的土壤腐蚀引起了普遍的重视,防止接地极腐蚀已成为一个重要的研究课题。本文介绍了目前我国电网和电气设备接地极的选材,接地极土壤腐蚀的特点,并对接地极防腐蚀方法做了简单总结。     

莱特生物强化技术处理高浓度有机废水的中试

采用莱特生物强化技术(LTBR—Littoral BioReactor),对兰州石化公司化工园区高浓度有机废水进行了中试试验,进行了正常运行的常规标定、水量冲击标定、浓度冲击标定。结果表明:采用LTBR生物处理工艺,使用特效微生物和营养基质,可以在高COD、高含盐等不利条件下正常进行有机物降解,达到了必须将废水中的COD降至2000mg/L以下的试验要求,为处理高浓度有机化工废水的工程应用开辟了新思路。     

Immobilization of non-point phosphorus using stabilized magnetite nanoparticles with enhanced transportability and reactivity in soils

Laboratory batch and column experiments were conducted to investigate the immobilization of phosphorus (P) in soils using synthetic magnetite nanoparticles stabilized with sodium carboxymethyl cellulose (CMC-NP). Although CMC-stabilized magnetite particles were at the nanoscale, phosphorus removal by the nanoparticles was less than that of microparticles (MP) without the stabilizer due to the reduced P reactivity caused by the coating. The P reactivity of CMC-NP was effectively recovered when cellulase was added to degrade the coating. For subsurface non-point P pollution control for a water pond, it is possible to inject CMC-NP to form an enclosed protection wall in the surrounding soils. Non-stabilized “nanomagnetite” could not pass through the soil column under gravity because it quickly agglomerated into microparticles. The immobilized P was 30% in the control soil column, 33% when treated by non-stabilized MP, 45% when treated by CMC-NP, and 73% when treated by both CMC-NP and cellulase.     

Determination of antibiotics in sewage from hospitals, nursery and slaughter house, wastewater treatment plant and source water in Chongqing region of Three Gorge Reservoir in China

Sewage samples from 4 hospitals, 1 nursery, 1 slaughter house, 1 wastewater treatment plant and 5 source water samples of Chongqing region of Three Gorge Reservoir were analyzed for macrolide, lincosamide, trimethoprim, fluorouinolone, sulfonamide and tetracycline antibiotics by online solid-phase extraction and liquid chromatography-tandem mass spectrometry. Results showed that the concentration of ofloxacin (OFX) in hospital was the highest among all water environments ranged from 1.660 μg/L to 4.240 μg/L and norfloxacin (NOR, 0.136-1.620 μg/L), ciproflaxacin (CIP, ranged from 0.011 μg/L to 0.136 μg/L), trimethoprim (TMP, 0.061-0.174 μg/L) were commonly detected. Removal range of antibiotics in the wastewater treatment plant was 18-100% and the removal ratio of tylosin, oxytetracycline and tetracycline were 100%. Relatively higher removal efficiencies were observed for tylosin (TYL), oxytetracycline (OXY) and tetracycline (TET)(100%), while lower removal efficiencies were observed for Trimethoprim (TMP, 1%), Epi-iso-chlorotetracycline (EICIC, 18%) and Erythromycin-H₂O (ERY-H₂O, 24%). Antibiotics were removed more efficiently in primary treatment compared with those in secondary treatment.     

A retrospective comparison of model-based forecasted PM2.5 concentrations with measurements

This study presents an assessment of the performance of the Community Multiscale Air Quality (CMAQ) photochemical model in forecasting daily PM2.5 (particulate matter < or = 2.5 microm in aerodynamic diameter) mass concentrations over most of the eastern United States for a 2-yr period from June 14, 2006 to June 13, 2008. Model predictions were compared with filter-based and continuous measurements of PM2.5 mass and species on a seasonal and regional basis. Results indicate an underprediction of PM2.5 mass in spring and summer, resulting from under-predictions in sulfate and total carbon concentrations. During winter, the model overpredicted mass concentrations, mostly at the urban sites in the northeastern United States because of overpredictions in unspeciated PM2.5 (suggesting possible overestimation of primary emissions) and sulfate. A comparison of observed and predicted diurnal profiles of PM2.5 mass at five sites in the domain showed significant discrepancies. Sulfate diurnal profiles agreed in shape across three sites in the southern portion of the domain but differed at two sites in the northern portion of the domain. Predicted organic carbon (OC) profiles were similar in shape to mass, suggesting that discrepancies in mass profiles probably resulted from the underprediction in OC. The diurnal profiles at a highly urbanized site in New York City suggested that the overpredictions at that site might be resulting from overpredictions during the morning and evening hours, displayed as sharp peaks in predicted profiles. An examination of the predicted planetary boundary layer (PBL) heights also showed possible issues in the modeling of PBL.