LIDAR Measurements of the Vertical Aerosol Profile and Optical Depth during the ACE-Asia 2001 IOP, at Gosan, Jeju Island, Korea

In order to investigate the characteristic of optical properties of Asian dust particles, the atmospheric aerosol vertical profile was measured with the multi-wavelength LIDAR system, at the Gosan super site (33 degrees 17'N, 126 degrees 10'E) in Jeju Island, Korea, during the ACE-Asia intensive observation period, 11 March-4 May 2001. An air mass backward trajectory analysis, using Hysplit-4, was carried out to track the aerosol plume, with high mass loading, from the Chinese desert regions during the period of Asian dust storm events. Vertical atmospheric aerosol profiles on three major Asian dust storm event days, 22 March and 13 and 26 April 2001, have been analyzed. The LIDAR-derived aerosol optical depth values were compared with those measured by a collocated sunphotometer.     

Mobility control: How injected surfactants and biostimulants may be forced into low‐permeability units

Recovering dense nonaqueous‐phase liquid (DNAPL) remains one of the most difficult problems facing the remediation industry. Still, the most common method of recovering DNAPL is to physically remove the contaminants using common technologies such as total fluids recovery pumps, vacuum systems, and “pump‐and‐treat.” Increased DNAPL removal can be attained using surfactants to mobilize and/or solubilize the pollutants. However, very little is understood of the methods developed by petroleum engineers beginning in the 1960s to overcome by‐passed, low‐permeability zones in heterogeneous oil reservoirs. By injecting or causing the formation of viscous fluids in the subsurface, petroleum engineers caused increased in‐situ pressures that forced fluid flow into low permeability units as well as the higher permeability thief zones. Polymer flooding involves injecting a viscous aqueous polymer solution into the contaminated aquifer. Foam flooding involves injecting surfactant to decontaminate the high‐permeability zones and then periodic pulses of air to cause a temporary viscous foam to form in the high‐permeable zones after all DNAPL is removed. Later surfactant pulses are directed by the foam into unswept low‐permeable units. These methods have been applied to DNAPL removal using surfactants but they can also be applied to the injection of bio‐amendments into low‐permeability zones still requiring continued remediation. Here we discuss the principles of mobility control as practiced in an alluvial aquifer contaminated with chlorinated solvent and coal tar DNAPLs as well as some field results. © 2003 Wiley Periodicals, Inc.     

Enhanced production of poly(3-hydroxybutyrate) by filamentation-suppressed recombinantEscherichia coli in a defined medium

Fed-batch cultures of recombinantEscherichia coli strains were carried out for the production of poly(3-hydroxybutyric acid) (PHB) in a chemically defined medium. TheE. coli strains used were XL1-Blue, harboring pSYL105, a stable high-copy number plasmid containing theAlcaligenes eutrophus polyhydroxyalkanoate (PHA) genes, and XL1-Blue, harboring pSYL107, which is pSYL105 containing theE. coli ftsZ gene to suppress filamentation. With XL1-Blue(pSYL105) the final cell mass and PHB concentration obtained in 62 h were 102 and 22.5 g/L, respectively. Fed-batch culture of XL1-Blue(pSYL107) under identical conditions resulted in a final cell mass and PHB concentration of 127.5 and 48.2 g/L, respectively. The PHB contents obtained with XL1-Blue(pSYL105) and XL1-Blue(pSYL107) were 22.1 and 37.8%, respectively. Therefore, PHB was more efficiently produced in a defined medium by employing filamentation-suppressed recombinantE. coli.     

Ozonation catalyzed by homogeneous and heterogeneous catalysts for degradation of DEHP in aqueous phase

Di-(2-ethyl hexyl) phthalate (DEHP), a recalcitrant and an endocrine disrupting chemical, was studied for its removal from wastewater by advanced oxidation process. The effects of pH, transition metal ions, and granular activated carbon (GAC) were investigated. Removal of DEHP increased with increase in pH and among metal ions Cr(III) was found to be the most active catalyst to remove DEHP. In the case of GAC, original carbon (G0) and GAC pre-ozonated in gas phase for 10 min (G10) were tested as catalysts in catalytic ozonation and found G0 to be more active than G10. This is because, during pre-ozonation, basic groups like chromene, pyrones and also graphene layers were oxidized to acidic surface oxygen groups. These basic surface groups are reported to be active catalytic centres for ozone decomposition into .OH which is a strong oxidant. According to kinetic manipulations, DEHP degradation rate constant due to .OH was affected by the catalyst while that due to direct ozonation is same in all cases with or without catalyst. G0 was doped with chromia gels (G0/CrA) to combine the benefits of homogeneous and heterogeneous catalysis. G0/CrA showed lower catalytic efficiency than that of only G0. This might be because of changes in surface structure of GAC caused by doping of chromia gel and changes in chemical nature of Cr(III) during formation of gel. A good correlation was found between the rate constants of ozone decay and DEHP degradation (R2=0.96). This correlation confirms that ozone decomposition into .OH is a critical factor for the activity of a catalyst during ozonation.     

Effect of temperature on single and competitive adsorptions of Cu(II) and Zn(II) onto natural clays

This study conducted a combined adsorption-sequential extractionanalysis (CASA), by which five phases (i.e., exchangeable, carbonate, Mn-Oxide, organic, and Fe-Oxide phases) of adsorbed heavy metals were analyzed, to investigate temperature effects on single and competitive adsorptions of Zn(II) and Cu(II) ontonatural clays. In the case of single adsorption of Zn, the exchangeable phase adsorption decreased from 65 to 40%, but thecarbonate phase adsorption increased from 30 to 40%, with an increase in temperature from 15 to 55 °C. However, in itscompetitive adsorption with Cu, Zn was mostly present in the exchangeable phase (over 90%), and with an increase in temperature, the exchangeable phase adsorption decreased only 10%. In the case of Cu, over 50% among the total amount of adsorption was present in the carbonate phase in both cases ofsingle and competitive adsorptions. The carbonate phaseadsorption of Cu increased from 56 to 61% and from 60 to 66% in single and competitive adsorptions, respectively, with atemperature increase. These results show that in the case of Zn,the major mechanism of retention in natural clay soils might beexchangeable phase adsorption, especially in the case of competitive adsorption with Cu. However, in the case of Cu, the major mechanism might be carbonate phase adsorption, which is known to be a more immobile phase than exchangeable phase adsorption. It seems that the adsorption of Zn and Cu onto natural clays is an endothermic reaction, which represents thatthe adsorption equilibrium constants and capacities increase with a temperature increase, with the exception of exchangeablephase adsorption.     

Efficacy of vermicomposting for recycling organic portion of hospital wastes using <Emphasis Type="Italic">Eisenia fetida</Emphasis>: standardization of cow manure proportion to increase enzymatic activities and fungal biomass

Hospital wastes are infectious wastes generated in hospitals and need to be disposed in such a way that they do not spread disease. In this experiment, 5, 10, 15 and 20% cow manure (CM) were mixed with hospital wastes (HW), and mixed wastes were subjected to vermicomposting. In control treatment, only HW was used for vermicomposting. Results suggested that significantly (P ≤ 0.05) higher total nitrogen content was recorded in vermicomposts when 10% or more CM was added to HW. Higher mineralization rate (decrease in C/N ratio) and cellulase activity is probably responsible for rapid organic matter decomposition (loss of total organic carbon). Ergosterol content i.e., total fungal biomass and cellulolytic fungal population were almost constant initially, but increased in the latter stage of vermicomposting. All the vermicompost samples, prepared in this experiment, showed the absence of coliform bacteria. Therefore, it could be concluded that 10% CM addition with HW was the most economical to obtain best quality vermicompost in terms of nutrient content and microbial status.     

Ultrasound pretreatment of filamentous algal biomass for enhanced biogas production

The filamentous alga Hydrodictyon reticulatum harvested from a bench-scale wastewater treatment pond was used to evaluate biogas production after ultrasound pretreatment. The effects of ultrasound pretreatment at a range of 10–5000 J/mL were tested with harvested H. reticulatum. Cell disruption by ultrasound was successful and showed a higher degree of disintegration at a higher applied energy. The range of 10–5000 J/mL ultrasound was able to disintegrated H. reticulatum and the soluble COD was increased from 250 mg/L to 1000 mg/L at 2500 J/mL. The disintegrated algal biomass was digested for biogas production in batch experiments. Both cumulative gas generation and volatile solids reduction data were obtained during the digestion. Cell disintegration due to ultrasound pretreatment increased the specific biogas production and degradation rates. Using the ultrasound approach, the specific methane production at a dose of 40 J/mL increased up to 384 mL/g-VS fed that was 2.3 times higher than the untreated sample. For disintegrated samples, the volatile solids reduction was greater with increased energy input, and the degradation increased slightly to 67% at a dose of 50 J/mL. The results also indicate that disintegration of the algal cells is the essential step for efficient anaerobic digestion of algal biomass.     

Melt Flow Behavior and Processability of Polylactic Acid/Polystyrene (PLA/PS) Polymer Blends

The present investigation dealt with the flow behavior and processability of polylactic acid/polystyrene (PLA/PS) polymer blends using a capillary rheometer. For this purpose, PLA/PS blends with different ratios of the concentrations were prepared using a single screw extruder. The shear viscosity, shear stress, shear rate, power-law index, viscous activation energy at a constant shear stress, and elongational stress were determined. PLA/PS blends exhibited a typical shear-thinning behavior over the entire range of shear rates tested, and the viscosity values of the blends would tend to decrease with increasing amount of PLA. In addition, the polymer blend of 70 % PLA and 30 % PS was found to be relatively less sensitive to the processing temperature, implying that the extrusion process was more desirable for fabrication of PLA/PS polymer blend than the injection process.