Synthesis and Characterization of a Thin-Film Composite Nanofiltration Membrane Based on Polyamide-Cellulose Acetate: Application for Water Purification

Membrane separation has been widely used for various applications including microfiltration (MF), ultrafiltration (UF), and nanofiltration (NF) processes in the fields of biomedicine, food, and water purification. In this work, a facile synthesis of new polyamide thin-film composite nanofiltration membranes (NF-TFC) for water purification was described. The polyamide thin film was deposed over a synthetic cellulose acetate (CA) support by interfacial polymerization method. 1,3 cyclohexane bis (methylamine) (CHMA) and trimesoyl chloride (TMC) were used as monomers. The membranes were characterized using Scanning Electron Microscopy (SEM), Fourier Transform Infrared spectroscopy (FT-IR), water uptake, porosity, contact angle, water permeability and rejection towards specific salt and dye molecules. The effect of the variation of the CHMA concentration (0.2–2 wt.%) on the morphology, porosity, water permeation and rejection properties of the prepared membranes was studied. SEM results displayed the growth of the membrane thickness when the CHMA concentration increased from 0.2 to 2 wt.%. The strong adhesion between the cellulose acetate substrate and the polyamide layer explained by the formation of the polyamide film in the substrate surface and inside the pores. The water permeability varied from 36.02 to 17.09 L h^?1 m^?2 bar^?1. The salt rejection of Na₂SO₄ and NaCl increased from 9 to 68% and from 38.41% to 89.4%, respectively, when the CHMA concentration was changed from 0.2 to 2 wt.%. The prepared membranes were further applied successfully for the removal of malachite green and congo red. The results indicated that the maximum rejection reached 89% and 85% for malachite green and congo red, respectively.

     

Inspecting the influence of renewable energy and R&D in defending environmental quality: evidence for California

Environmental Science and Pollution Research - The United Nations’s Sustainable Development Goals (SDGs) is international cooperation that aims to climate change mitigation, and encourage the...     

Correction to: Reducing ammonia emission by aluminum sulfate addition in litter and its influence on productive,reproductive, and physiological parameters of dual-purpose breeding hens

Environmental Science and Pollution Research -     

Effects of environmentally relevant levels of polyethylene microplastic on Mytilus galloprovincialis (Mollusca: Bivalvia): filtration rate and oxidative stress

Environmental Science and Pollution Research - The objective of the present study was to evaluate the potential toxic effects of polyethylene microplastics (PE-MPs) (40–48 μm) on the...     

The diagnostic accuracy of intraoperative frozen section biopsy for diagnosis of sentinel lymph node metastasis in breast cancer patients: a meta-analysis

Environmental Science and Pollution Research - Sentinel lymph node (SLN) sampling is important for evaluating the nodal stage of breast cancer when the axillary nodes are clinically free of...     

Potential of Nassarius nitidus for monitoring organotin pollution in the lagoon of Bizerta （northern Tunisia）

Imposex and butyltin burden were assessed in Nassarius nitidus, Bolinus brandaris and Hexaplex trunculus collected at five stations in the Bizerta lagoon. Biological analysis showed that imposex followed type (a) in N nitidus (distal evolution), against type (d) in the two muricids (proximal evolution). Imposex indices were higher in sites located nearby sources of tributyltin and N nitidus was the least affected species of the five sites, followed by B. brandaris and H. trunculus. Butyltin analysis showed lower accumulation in N nitidus followed by H. trunculus and B. brandaris. This study has allowed the gathering of data on imposex in a snail studied for the first time in Tunisia (N. nitidus). It suggests the possibility of using such snail as a complementary species for organotin monitoring programs in the Mediterranean and further confirmed that H. trunculus is the most suitable species for such investigations.     

Biodegradation of imidacloprid in liquid media by an isolated wastewater fungus Aspergillus terreus YESM3

In the present study, a new fungal strain capable of imidacloprid degradation was isolated from agricultural wastewater drain. The fungal strain of YESM3 was identified as Aspergillus terreus based on ITS1-5.8S rDNA-ITS2 gene sequence by PCR amplification of a 500 bp sequence. Screening of A. terreus YESM3 to the insecticide imidacloprid tolerance was achieved by growing fungus in Czapek Dox agar for 6 days at 28°C. High values (1.13 and 0.94 cm cm^?1) of tolerance index (TI) were recorded at 25 and 50 mg L^?1 of imidacloprid, respectively in the presence and absence of sucrose. However, at 400 mg L^?1 the fungus did not grow. Effects of the imidacloprid concentration, pH, and inoculum size on the biodegradation percentage were tested using Box–Behnken statistical design and the biodegradation was monitored by HPLC analysis at different time intervals. Box–Behnken results indicated that optimal conditions for biodegradation were at pH 4 and two fungal discs (10 mm diameter) in the presence of 61.2 mg L^?1 of imidacloprid. A. terreus YESM3 strain was capable of degrading 85% of imidacloprid 25 mg L^?1 in Czapek Dox broth medium at pH 4 and 28°C for 6 days under static conditions. In addition, after 20 days of inoculation, biodegradation recorded 96.23% of 25 mg L^?1 imidacloprid. Degradation kinetics showed that the imidacloprid followed the first order kinetics with half-life (t₅₀) of 1.532 day. Intermediate product identified as 6-chloronicotinic acid (6CNA) as one of the major metabolites during degradation of imidacloprid by using HPLC. Thus, A. terreus YESM3 showed a potential to reduce pollution by pesticides and toxicity in the effected environment. However, further studies should be conducted to understand the biodegradation mechanism of this pesticide in liquid media.     

Oxidation of natural and synthetic hormones by the horseradish peroxidase enzyme in wastewater

Steroid estrogens, including both natural estrogens (e.g., estrone - E1; 17beta-estradiol - E2; and estriol - E3) and synthetic estrogens (e.g., 17alpha-ethinylestradiol - EE2), are known as endocrine-disrupting compounds. The objective of this research was to evaluate the feasibility of the enzymatic oxidation of estrogens and to optimize this process in municipal wastewater contaminated with steroid estrogens using horseradish peroxidase (HRP) and hydrogen peroxide. An initial HRP activity of 0.02 U ml(-1) was sufficient to completely remove EE2 from the synthetic solution, although greater HRP doses (up to 0.06 U ml(-1)) were required to remove E1, E2 and E3. The optimal molar peroxide-to-substrate ratio was determined to be approximately 0.45. Based on the Michaelis-Menten kinetics, the HRP had an increasing reactivity with E1, E3, E2, and EE2, in increasing order. In real activated sludge process effluent, an HRP dose of 8-10 U ml(-1) was required to completely remove all of the studied estrogens, while only 0.032 U ml(-1) of HRP was necessary to treat synthetic water containing the same estrogen concentrations.     

Effect of Manufacturing Process and Xanthan Gum Addition on the Properties of Cassava Starch Films

The objective of this work was to manufacture biodegradable films by two different processes (casting and extrusion), from different combinations of cassava starch and xanthan gum. These films were produced by casting and by extrusion from six different starch-xanthan gum combinations (0, 2, 4, 6, 8 and 10% w/w), containing glycerol as plasticizer (20% w/w) and were also characterized according to their microstructure, optical, mechanical, and barrier properties. Scanning electron microscopy of the starch-xanthan gum extruded films showed reticulated surface and smooth interior, suggesting that xanthan was driven to the surface and gelatinized starch to the interior of the films during extrusion. Films manufactured by casting were entirely homogeneous. In general, casted films presented lower opacity and water vapor permeability and higher stress at break than films manufactured by extrusion. Xanthan gum addition affected mechanical properties of starch films, improving their stress and strain at break, especially for extruded samples, but these properties did not show stability at different RH conditions.