Distribution and Fractionation of Heavy Metals in Solid Waste from Selected Sites in the Industrial Belt of Delhi, India

Solid waste samples were collected from five small-scale industrial sites in the National Capital Territory (NCT) of Delhi. These industrial sites represent the regional spread of the industrial belt in the NCT of Delhi. Solid waste samples were digested using aqua-regia and HF in air tight teflon bombs for the quantitative analysis of heavy metals (Hg, Pb, Cd, Mn, Fe, Ni, Cu and Zn) by GBC model 902 atomic absorption spectrophotometer. Hg was analysed using hydrid generator attachment. Beside this sequential extraction was used to fractionate five heavy metals (Pb, Ni, Cd, Cu and Zn) into six operationally defined phases, viz. water soluble, exchangeable, carbonate-bound, Fe-Mn oxides, organic-bound and residual fractions to ascertain the relative mobility of these metals. The result obtained showed metal concentration to be in the range of Hg 0.42-2.3; Pb 23-530; Cd 014-224; Mn 494-19 964; Fe 35 684-233 119; Ni 192-1534; Cu 3065-10 144 and Zn 116-23 321 (all units in mg kg(-1)) in all the industrial areas studied. The fractionated toxic metals like Pb, Ni and Cd were observed to be in the range of 25-35, 15-50 and 40-50%, respectively, in mobile or bio-available fractions of solid waste. As this waste is often disposed-off by the roadsides, low lying areas, abandoned quarries or in landfill sites which are often not properly planned, thus posing potential risk to ground and surface water quality to millions of people living downstream.     

Numerical integration of chemical ODE problems arising in air pollution models

The numerical treatment of a regional air pollution model (such models are, as a rule, described mathematically by systems of partial differential equations) leads to the solution of very large computational problems. The chemical submodel of an air pollution model is normally the most timeconsuming part of the computational work. The application of appropriate discretization and splitting procedures reduces the chemical submodel to a large number of relatively small ODE systems (one such system per gridpoint). In the process of searching for efficient numerical algorithms for the chemical submodels one can carry out experiments by using only one such ODE system in order to facilitate the work. This approach has been used in connection with a particular chemical scheme, the condensed CBM IV scheme, which is used in several large air pollution models. Six integration algorithms have been tested on a set of typical scenarios (consisting of different starting concentrations and/or of different values of the emissions). The advantages and the disadvantages of the algorithms tested are discussed. The final decision about the most efficient algorithm, among the algorithms tested, should be made after a second series of experiments. The coupling of the chemical process with the transport of air pollution (on, at least, a twodimensional domain) together with the application of highspeed computers has to be studied in the second series of experiments, which will be performed in a subsequent paper.     

Dissolved insecticides and polychlorinated biphenyls in the Pearl River Estuary and South China Sea

Persistent organic pollutants (POPs) such as organochlorine (OCl) insecticides and polychlorinated biphenyls (PCB), together with the new generation of organophosphorus (OP) insecticides, are of global concern, due to their widespread occurrence, persistence, bioaccumulation and hormone disruption potential. This paper represents an attempt to study the source and transportation of such pollutants in estuarine and coastal environments as an integrated ecosystem, by determining the levels of 18 OCl insecticides, 21 PCB congeners, and 17 OP insecticides in the Pearl River Estuary and South China Sea. The total concentrations varied from 126-1198 ng l(-1) for OCl insecticides, 33.38-1064 ng l(-1) for PCB congeners, and 4.44-6356 ng l(-1) for OP insecticides in the Pearl River Estuary. In comparison, their levels in the South China Sea were significantly lower, varying from 57.09-202 ng l(-1) for OCl insecticides, 21.72-144 ng l(-1) for PCBs, and 1.27-122 ng l(-1) for OP insecticides, respectively. The predominance of beta-HCH in HCHs, and DDE in DDTs in all water samples was clearly observed, suggesting beta-HCH and DDE's resistance to further degradation. The PCBs were dominated by those with 3-6 chlorines. The distribution characteristic of OP insecticides shows that five compounds (methamidophos, dimethoate, malathion, dichlorvos and omethoate) accounted for 56% and 72% of the total OP insecticide concentration. The relationship between pollutant concentrations and salinity in the estuary showed that they were all removed during the mixing process, therefore behaving non-conservatively.     

Occurrence and behaviour of organophosphorus insecticides in the River Wuchuan,southeast China

Organophosphorus (OP) insecticides are used worldwide, yet their persistence in the environment is not well understood. This paper summarises recent research on 17 OP insecticides in the River Wuchuan, an important catchment in China, by determining their concentrations in water, soil, sediment and plants by gas chromatography with flame photometric detection (GC-FPD). The concentrations of the total OP insecticides ranged from 92.77 to 229 ng l-1 in river water, 1.61 to 9.93 ng g-1 dry weight in soil, 1.24 to 7.56 ng g-1 dry weight in sediment and 75.28 to 326 ng g-1 dry weight in plants. There was a relatively high abundance of methamidophos, dichlorvos, malathion, omethoate and dimethoate in all water, soil, sediment and plant samples. On average, these five compounds collectively accounted for 64%, 71%, 71% and 54% of the total OP insecticide concentration in water, soil, sediment and plants, respectively, which was similar to the composition of OP insecticides in application formulations used in our study area and in China as a whole. The results therefore reflect the application pattern to some extent, and suggest that the sources of the OP insecticides are mainly from current usage. When compared with other areas, the levels of OP insecticides in the River Wuchuan were moderate. The animal and human risks from exposure to OP insecticides in water and plants were evaluated against relevant threshold values. The results therefore provide important information on the current contamination status of a key agricultural watershed in China, and point to the need for urgent action to control the use of some excessively applied and potentially persistent agrochemicals, such as methamidophos, omethoate and dimethoate.     

Effect of inhibitors of carbonic anhydrase activity on photosynthesis in the red alga Soliera filiformis (Gigartinales: Rhodophyta)

The effect of light intensity, pH and carbonic anhydrase (CA) inhibitors on photosynthesis of the red marine macroalgae Solieria filiformis (Kützing) Gabrielson, collected from Taliarte (Gran Canaria, Canary Islands) in 1991, has been investigated. Plants taken from the sea (wild phenotype) developed spherical morphology (ball phenotype) after 2 mo culture in aerated tanks. The photosynthetic oxygen evolution in the wild phenotype was saturated at 100 mol photons m^-2s^-1, while the ball phenotype displayed saturation at 200 mol photons m^-2s^-1. The inhibitors of total CA activity (6-ethoxizolamide) and extracellular CA activity (dextran-bound sulfonamide) inhibited photosynthesis at pH 8.2, to 90 and 50% respectively, in both phenotypes. No inhibition of the photosynthetic oxygen evolution was detected at pH 6.5. CA activity was associated with both supernatant and pellet fractions of crude extracts of S. filiformis. The rate of alkalization of the medium by the algae was dependent on light intensity. We suggest that carbon dioxide is the general form of inorganic carbon transported across the plasmamembrane in S. filiformis. HCO₃ transport into the cell takes place simultaneously by an indirect mechanism (dehydration to CO₂ catalyzed by CAext) and by direct uptake. Extracellular (CAext) and intracellular (CAint) CAs are involved in the mechanisms of inorganic carbon assimilation by S. filiformis.     

Environmental assessment of laser assisted manufacturing: case studies on laser shock peening and laser assisted turning

Laser assisted manufacturing processes, when compared with traditional manufacturing processes, have the potential to reduce cost, increase surface resistance to wear and fatigue, extend part/tool life, and expand the range of manufacturable materials. These processes have found niche applications in automotive, aerospace, and defense industries. However, very limited research has been conducted to evaluate and compare the environmental performance of laser assisted processes with traditional methods. This paper conducts case studies on two representative laser based processes, i.e. laser shock peening of 7075-T7351 Aluminum and laser assisted turning of compacted graphite iron. Life cycle assessment is used to benchmark the environmental performance of these two processes to conventional processes, i.e. shot peening and turning, respectively. The life cycle inventory of both the laser based processes and conventional processes are developed using SimaPro 7.1 and the Ecoinvent 2.0 database and life cycle impact assessment is performed using US EPA TRACI. The results of this study show that the environmental performance of the two laser based processes is significantly better than conventional processes. For laser shock peening of aluminum, contribution analysis indicates that this is mainly due to the significant extension of fatigue life of the workpiece being treated. For laser assisted turning of compacted graphite iron, the improved performance is mainly due to the extended tool life since cutting tool manufacturing is an energy intensive process. Development of high-power laser with a lower wavelength (e.g. direct diode system) could eliminate the use of paint in laser assisted turning. This, along with improved wall plug efficiency, makes laser assisted turning even more environmentally benign compared to conventional process. A brief cost analysis suggests that both laser shock peening and laser assisted turning can be economically viable with payback period less than three years for niche applications.     

Plutonium isotopes in surface air of Prague in 1986–2006

Monitoring of ^239,240Pu in surface air of Prague started in 1986 in connection with the Chernobyl accident. Measurable activities of 10–28 μBq m⁻³ were found from 29 April 1986 to 5 May 1986. In the most of the monitoring periods of 1987–1996, activities of ^239,240Pu in air were not measurable. Positive values for ^239,240Pu and ²³⁸Pu in air could be obtained after installation of an aerosol sampler with higher flow-rate in 1997. Activity concentrations of ^239,240Pu and ²³⁸Pu in Prague air in the most of quarters of 1997–2006 were in the range 0.53–5.06 and <0.16–1.10 nBq m⁻³, respectively. Seasonal fluctuations can be found in content of ^239,240Pu in air. Activity ratios of ²³⁸Pu/^239,240Pu in air are higher than those in top soil, so it can be supposed that ²³⁸Pu is coming to air of Prague also from other sources than resuspension of fallout from atmospheric nuclear tests.