Study on the denitrification performance of FexLayOz/activated coke for NH3-SCR and the effect of CO escaped from activated coke at mid-high temperature on catalytic activity

Currently, activated coke is widely used in the removal of multiple pollutants from industrial flue gas. In this paper, a series of novel Fe_xLa_yO_z/AC catalysts was prepared by the incipient wetness impregnation for NH₃-SCR denitrification reaction. The introduction of Fe-La bimetal oxides significantly improved the denitrification performance of activated coke at mid-high temperature, and 4% Fe_0.3La_0.7O_1.5/AC exhibited a superior NO_x conversion efficiency of 90.1% at 400 °C. The catalysts were further characterized by BET, SEM, XRD, Raman, EPR, XPS, FTIR, NH₃-TPD, H₂-TPR, et al., whose results showed that the perovskite-type oxide of LaFeO₃ and oxygen vacancies were produced on the catalysts’ surfaces during roasting. Fe-La doping enhanced the amount of acid sites (mainly Lewis and other stronger acid sites) and the content of multifarious oxygen species, which were beneficial for NO_x removal at mid-high temperature. Moreover, it was investigated that the effect of released CO from activated coke at mid-high temperature on the NO_x removal through the lifetime test, in which it was found that a large amount of CO produced by pyrolysis of activated coke could promote the NO_x removal, and long-term escaping of CO on the activated coke carrier did not have a significant negative impact on catalytic performance. The results of the TG-IR test showed that volatile matter is released from the activated coke while TG results showed that the weight loss rate of 4% Fe_0.3La_0.7O_1.5/AC only was 0.0015~0.007%/min at 300–400 °C. Hence, 4% Fe_0.3La_0.7O_1.5/AC had excellent thermal stability and denitrification performance to be continuously used at mid-high temperature. Finally, the mechanisms were proposed on the basis of experiments and characterization results.

     

Effective cleanup of oil contamination on bio-inspired superhydrophobic surface

Environmental Science and Pollution Research - The oil-water separation is a popular issue and the removal of oil from bulk water is also meaningful especially in oil spill incident, which not only...     

Associations between ambient high temperatures and suicide mortality: a multi-city time-series study in China

Environmental Science and Pollution Research - Suicide prevention has become a public health issue of great concern. Previous studies proved that ambient temperature had an impact on suicide death,...     

对苯二甲酸降解菌固定化生物流化床处理精对苯二甲酸废水

采用微生物筛选、纯化技术,获得了降解对苯二甲酸（TA）的YPC—TA1,YPC—TA2,YPC-TA3,YPC—TA44株菌株。将筛选出的TA降解菌固定化,处理初始TA质量浓度为2650mg／L的模拟废水,降解36h后TA去除率达100％。用TA降解芮在生物流化床反应器中处理PTA废水,最佳容积负荷为6.7kg／（m^3·d）。生物流化床反应器可在容积负荷为6．0～6．5kg／（m^3·d）的较佳条件下长周期稳定运行,COD去除率保持在91％左右,TA去除率保持在94％左右。低pH废水冲击和高容积负荷废水冲击时COD,TA去除率均明显下降,恢复正常讲水后3～4d,COD,TA去除率均恢复正常。     

膜过滤-气相色谱法测定涂料中的苯系物、环己酮和甲苯二异氰酸酯

采用膜过滤-气相色谱法测定涂料中的苯系物、环己酮和甲苯二异氰酸酯（TD I）。用7种规格的石英毛细管色谱柱对混合标准溶液和涂料试样进行了分析实验,实验结果表明,不同属性的涂料试样添加固定量的正十四烷作内标物,经膜过滤净化后,苯系物、环己酮和TD I可采用DB-1-3或DB-1-2色谱柱同时分离并测定。测试数据经多级校准曲线处理后涂料试样中苯系物、环己酮和TD I的加标回收率为98.6%～101.8%,各组分分析结果的变异系数均小于2.0%,检出限均小于1.50×10^-5g。     

纳米晶粒TiO2多孔微球的制备及其光催化性能的研究进展

介绍了纳米晶粒TiO2多孔微球的主要制备方法、主要参量及表征、光催化性能研究进展,指出了纳米晶粒TiO2多孔微球制备过程的技术关键与基本参量的功能。针对目前存在的问题,提出了今后的主要研究方向,并展望了纳米晶粒TiO2多孔微球在水处理领域的应用前景。     

厌氧-好氧生物反应器填埋工艺特性研究

基于生物反应器填埋技术,研究1种填埋场地循环操作的厌氧-好氧生物反应器填埋工艺,设计了该工艺模拟装置并研究了其运行工艺特性.厌氧阶段主要通过渗滤液回灌控制反应器工艺条件,主要试验结果为,pH值,R1在 6周后可上升至6.7～7.8,R2在17周内一直低于6.8;渗滤液COD浓度,R1在13周时下降至10?617 mg/L,R2在5周后上升至60?000 mg/L后长期趋于稳定;填埋气累计产量,R1在8周达到44%,R2几乎不产气.衡量稳定化可以分别采用渗滤液pH、COD浓度及BOD₅/COD的减少率、填埋气的累计产率等指标来判断,并据此转换为好氧填埋运行.好氧阶段主要是通过强制通风来减少恶臭和水分,主要试验结果为,通风19d氨气浓度降为1.16 mg/m³,通风23d后恶臭浓度降为19;通风14d后含水率降为26%.完成此阶段的工艺指标值可依据矿化垃圾开采的最终用途确定.对主要试验数据进行了数值模拟.厌氧-好氧填埋过程的微生物演替经RISA分析,有4个优势菌群,一些兼性菌群在厌氧-好氧阶段起着重要的承前启后作用.     

阳离子型聚合物对低温低浊水的絮凝效果与形态学特性

采用微絮凝-深床直接过滤工艺,以西安市曲江水厂低温低浊水质为原水(水温低于10 ℃,初始浊度低于10NTU),投加阳离子型聚合物(简称CP)作主混凝剂或助凝剂,借助分形数学理论与图像分析技术,对滤料粒径、原水浊度、原水温度、药剂种类、聚合物分子量及投加量、混合强度等因素对处理效果的影响进行了研究,分析探讨了不同药剂处理低温低浊水的作用机理、絮凝形态学特征以及絮体结构的分形特性.结果表明,①当温度低于4 ℃、初始浊度小于4NTU时,不宜单独采用Al2(SO4)3或PAC作为絮凝剂;当温度为4～10 ℃、初始浊度小于10NTU时,如果只投加Al2(SO4)3或PAC作为絮凝剂,宜用细砂滤料过滤;低温低浊条件下,无机混凝剂形成的絮体粒径小、结构松散脆弱、有效质量密度低、沉速慢,但表征絮体分形特性的分维值较高.②CP作絮凝剂能显著改善低温低浊水的絮凝效果与过滤性能,但混合强度需增大,宜用粗砂滤料过滤;③单独用CP作絮凝剂时,宜投加分子量较低的弱阳性聚合物或投加低剂量较高分子量的强阳性聚合物;CP用作助凝剂时,能显著减少主混凝剂用量,但宜投加强阳性聚合物或增加弱阳性聚合物的剂量.④CP兼备电性中和与吸附架桥絮凝作用,能形成粒径较大、吸附性能与过滤性能良好的网状絮体构型,其有效质量密度高,产生的污泥量少,污泥沉降速度快,脱水效果好,但分维值低.⑤各种水处理药剂的处理效果为:Al2(SO4)3(或PAC) CP＞CP＞PAC＞Al2(SO4)3,这种差别由絮体的形态学特性与构型特征各异引起.     

La2O3-CeO2/γ-Al2O3催化剂还原脱硫耐氧特性及其反应机理研究

用浸渍法制备了一系列稀土催化剂,研究了其催化CO还原SO2为单质硫的耐氧特性及影响其耐氧性能的主要因素,运用XRD技术分析了催化剂物相的变化及脱硫产物成分.结果表明,12% La2O3-8% CeO2/γ-Al2O3复组分催化剂比其他La2O3-CeO2/γ-Al2O3催化剂具有更好的耐氧性能;脱硫温度、催化剂用量、SO2与CO的摩尔比等对催化剂的耐氧性能均有明显的影响.最后,探讨了稀土催化剂脱硫机理,并分析在有O2条件下,引起脱硫率下降的原因是反应过程中O2与CO、S发生了竞争性反应.     

土壤有机物污染控制标准制订的方法学研究

指出了中国现行土壤环境质量标准存在的问题.对日本和美国等发达国家的有机物污染土壤质量控制标准进行了分析.从土壤环境质量基准制订的方法学和污染控制标准的确定原则上,提出了制订中国土壤有机物污染控制标准的建议.