Promoting e-mobility in India: challenges,framework, and future roadmap

The purpose of the research is to identify the critical challenges that are impeding the adoption of e-mobility in India. It also aims to give a roadmap how to address these challenges while taking into considerations concerns of all the relevant stakeholders. Based on an in-depth literature review, an exploratory research design is employed to delve deep into various aspects of e-mobility. This is followed by a three-phase Delphi technique to identify and rate the e-mobility challenges in the Indian context. The study successfully identifies four different categories of challenges and proposes integrative framework for e-mobility. Further, the research goes on to lay out the future roadmap for mass adoption of electric vehicles (EVs) in India. The research is novel in terms of presenting a holistic viewpoint on e-mobility in India. Its originality lies in identifying the major inhibitors obstructing EVs adoption in India and then suggesting the roadmap how to overcome these impediments for mass adoption of e-mobility.     

Preparation of black lyophilic ink using the carbon soot emitted by vehicles

Environmental Science and Pollution Research - The carbon soot is formed as a consequence of incomplete combustion of hydrocarbons and organic matter. It causes respiratory diseases like lung...     

Investigation of performance enhancement of solar still incorporated with Gallus gallus domesticus cascara as sensible heat storage material

In this research work, the conventional single slope still (CSS) with egg shells of breed Gallus gallus domesticus cascara as sensible heat storage (SHS) material are studied experimentally to enhance the yield. In this experimental investigation, the proposed single slope still (PSS) with SHS material was made in comparison with the CSS to evaluate the productivity of fresh water under the same ambient conditions. Comparatively, this PSS has higher thermal conductivity than the CSS. The yield obtained from the PSS is 2.46 L/m², while the yield from the CSS is 2.07 L/m². The average rate at which the rise of output fresh water obtained from the PSS is 18% more than the fresh water output obtained from the CSS. The daily energy efficiency of the PSS is 26.07%, and for the CSS, it is only 22.25%. The daily exergy efficiency of the PSS is 2.36%, and for the CSS, it is only 1.67%. Since using the egg shell will employ as organic waste management and modification in this still is economical, less initial, and maintenance cost.

     

Assessment of inherent vulnerability of forests at landscape level: a case study from Western Ghats in India

Assessment of vulnerability is an important step in building long-term resilience in the forestry sector. The objective of this paper is to present a methodological approach to assess inherent vulnerability of forests at landscape level. The approach involves use of vulnerability indicators, the pairwise comparison method, and geographic information system (GIS) tools. We apply this approach to assess the inherent vulnerability of forests of the Western Ghats Karnataka (WGK) landscape, which is a part of the Western Ghats biodiversity hotspot in India. Four vulnerability indicators, namely biological richness, disturbance index, canopy cover, and slope, are selected. We find that forests in 30, 36, 19, and 15 % grid points in this region show low, medium, high, and very high inherent vulnerability, respectively. The forest showing high and very high inherent vulnerability are mostly dry deciduous forests and plantations located largely on the eastern side of the landscape. We also find that canopy cover is one of the key indicators that determine the inherent vulnerability of forests, and natural forests are inherently less vulnerable than man-made plantations. Spatial assessment of inherent vulnerability of forests at landscape level is particularly useful for developing strategies to build resilience to current stressors and climate change in future.     

Design and manufacturing of femoral stems for the Indian population

Several researchers have stressed the need for a proper implant-patient match in hip joint replacements, in particular, for cementless femoral stems. Some of the complications of mismatch are aseptic loosening, improper load distribution, and discomfort. In this study, the differences in dimensions between femurs of elderly Indians and those of populations from other regions are compared in order to solve the problem of a possible geometric mismatch between a selected implant and the femurs of an Indian patients are concerned. This paper also describes a methodology for implant designing from measured anthropometric data, fit evaluation, finite element (FE) stress analysis and subsequently implant manufacturing using the CAM (Computer Aided Manufacturing) technique. The machining of the Titanium alloy femoral stem is usually performed on a 5 Axis CNC (Computer Numerical Control) machining center. However, in this study the machining of the femoral stem was effectively performed on a 3 Axis CNC machining center to emphasize on economical benefits for low cost manufacturing strategy.     

Environmental forensic investigation of the air pollution from a cement manufacturing unit

Abstract

Cement manufacturing is a process that results in the emission of significant quantities of suspended particulate matter (SPM) to the ambient air. An environmental forensic investigation was carried out in the surroundings of a major cement manufacturing unit at a place called Coimbatore in the southern Indian state of Tamil Nadu. The investigation was carried out to identify the contribution of the cement manufacturing unit to the SPM concentration of the surrounding air environment. The sampling points’ selection and sample collection were done following the principles outlined in the INTERPOL Manual for Pollution Crime Forensic Investigation. On-site monitoring of the air samples was carried out using Mini Laser Aerosol Spectrometer (GRIMM, Mini-LAS Model 11R). The instrument was capable of measuring particles ranging from 0.25 to 32 µm and classifying them into 31 size channels. The test results at majority of the monitoring locations were well above the limits specified in the National Ambient Air Quality Standards of India. Microscopic studies of the dust samples were carried out for surface texture and particle shape. The spatial distribution of particles was analysed using geographic information system (GIS) for the visual identification of the extent of the pollution by keeping the cement factory as the focal point. The results from the GIS and microscopic analysis established the role of the cement factory in the particulate matter pollution of its surroundings, specifically in the areas North-West of the factory. The successfully adopted procedure can serve as a guideline for the environmental forensic investigation of similar pollution incidences.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Assessment of metal enrichments in tsunamigenic sediments of Pichavaram mangroves, southeast coast of India

The 26 December 2004-Tsunami has deposited sediments in the Pichavaram mangrove ecosystem, east coast of India. Ten surface and three core sediment samples were collected within thirty days of the event. High concentrations of Cd, Cu, Cr, Pb, and Ni were observed in the tsunamigenic sediments. With respect to Fe, Zn, and Mn, there was little variation as compared to pre-tsunami values. The geo-accumulation index was calculated in order to assess the contamination of heavy metals in the sediments. The sediments were extremely contaminated with respect to Cd and they showed moderate to strong contamination with respect to Cr, Pb and Ni. The study highlighted the future risk of enhanced metal pollution in near future in this mangrove ecosystem.     

Atmospheric deposition of heavy metals (Cu, Zn, Cd and Pb) in Varanasi City, India

Rapid growth in urbanization and industrialization in developing countries may significantly contribute in heavy metal contamination of vegetables through atmospheric depositions. In the present study, an assessment was made to investigate the spatial and seasonal variations in deposition rates of heavy metals and its contribution to contamination of palak (Beta vulgaris). Samples of bulk atmospheric deposits and Beta vulgaris for analysis of Cu, Zn, Cd and Pb were collected from different sampling locations differing in traffic density and land use patterns. The results showed that the sampling locations situated in industrial or commercial areas with heavy traffic load showed significantly elevated levels of Cu, Zn and Cd deposition rate as compared to those situated in residential areas with low traffic load. The deposition rates of Cu, Zn and Cd were significantly higher in summer and winter as compared to rainy season, however, Pb deposition rate was significantly higher in rainy and summer seasons as compared to winter season. Atmospheric depositions have significantly elevated the levels of heavy metals in B. vulgaris collected during evening as compared to those collected in morning hours. The study further showed that local population has maximum exposure to Cd contamination through consumption of B. vulgaris. The present study clearly points out the urban and industrial activities of a city have potential to elevate the levels of heavy metals in the atmospheric deposits, which may consequently contaminate the food chain and thus posing health risk to the local population.     

Development of a highly sensitive extractive spectrophotometric method for the determination of nickel(II) from environmental matrices using N-ethyl-3-carbazolecarboxaldehyde-3-thiosemicarbazone

Nickel(II) reacts with N-ethyl-3-carbazolecarboxaldehyde-3-thiosemicarbazone (ECCT) and forms a yellow colored complex, which was extracted into n-butanol from sodium acetate and acetic acid buffer at pH 6.0. The absorbance value of the Ni(II)-ECCT complex was measured at different intervals of time at 400nm, to ascertain the time stability of the complex. The extraction of the complex into the solvent was instantaneous and stable for more than 72h. The system obeyed Beer's law in the concentration range of 1.2-5.6mugml(-1) of nickel(II), with an excellent linearity and a correlation coefficient of 0.999. The molar absorptivity and Sandell's sensitivity of the extracted species were found to be 1.114x10(4)Lmol(-1)cm(-1) and 5.29x10(-3)mugcm(-2) at 400nm, respectively. Hence, a detailed study of the extraction of nickel(II) with ECCT has been undertaken with a view to developing a rapid and sensitive extractive spectrophotometric method for the determination of nickel(II) when present alone or in the presence of diverse ions which are usually associated with nickel(II) in environmental matrices like soil and industrial effluents. Various standard alloy samples (CM 247 LC, IN 718, BCS 233, 266, 253 and 251) have been tested for the determination of nickel for the purpose of validation of the present method. The results of the proposed method are comparable with those from atomic absorption spectrometry and were found to be in good agreement.