Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

Microbial population dynamics at effluent treatment plants

The requirements for treated wastewater are becoming increasingly more stringent, and therefore the improved efficiency of biological treatment processes is indispensable at industrial effluent treatment plants (ETPs). Microorganisms such as bacteria play an important role in the natural cycling of materials and particularly in the decomposition of organic wastes. The knowledge of the interactions among these microbial populations needs to be harnessed for optimum evaluation and functioning of effluent treatment plants. Modern molecular techniques have revolutionized the methods of assessing these microbial populations. The combination of the results of these microbial assessments along with the on-site parameters at ETPs would favor an efficient treatment. In this review, the various approaches and importance of correlating the microbial population dynamics and treatment of wastewater at industrial ETPs has been elaborated.     

MODELING LIGHT ATTENUATION,SECCHI DISK,AND EFFECTS OF TRIPTON IN SENACA RIVER,NEW YORK,USA1

The development, testing, and application of a probabilistic model framework for the light attenuation coefficient for downwelling irradiance (K_d) and Secchi disc transparency (SD) that resolves the effects of several light attenuating constituents, including phytoplankton and nonliving particles (tripton), is documented. The model is consistent with optical theory, partitioning the magnitudes of the light attenuating processes of absorption and scattering according to the contributions of attenuating constituents as simple summations. The probabilistic framework accommodates variations in the character and concentrations of these constituents and ambient conditions during measurements, and recognizes a linear relationship between the magnitudes of absorption and scattering by tripton. The model is tested and applied for a 21 km reach of the Seneca River, New York, that features optical gradients caused by an intervening hypereutrophic lake and dam, and a severe infestation of the exotic zebra mussel. The model is applied to resolve the roles of phytoplankton and tripton in regulating measured longitudinal patterns of SD along the study reach of the river and increases in SD since the zebra mussel invasion, and to predict decreases in K_d since the invasion.     

Geospatial technology for assessment of soil erosion and prioritization of watersheds using RUSLE model for lower Sutlej sub-basin of Punjab,India

Environmental Science and Pollution Research - Erosion of soil by water coupled with human activities is considered as one of the...     

Simulations and experiments in punching spring-steel devices with sub-millimeter features

This work demonstrates the feasibility of meso-scale (100 μm to mm) punching of multiple holes of intricate shapes in metals. Analytical modeling, finite element (FE) simulation, and experimentation are used in this work. Two-dimensional FE simulations in ABAQUS were done with an assumed material modeling and plane-strain condition. A known analytical model was used and compared with the ABAQUS simulation results to understand the effects of clearance between the punch and the die. FE simulation in ABAQUS was done for different clearances and corner radii of the punch, die, and holder. To complement modeling with real experiments and for the purpose of comparison, a set of punches and dies were made to punch out a miniature spring-steel gripper. Comparison of compliant grippers made by wire-cut electro discharge machining (EDM) and punching shows that realizing sharp interior and re-entrant corners by punching is not easy to achieve. However, the promise of realizing meso-scale parts with complicated shapes through punching is demonstrated in this work; and further work is identified and some strategies are suggested for improvement. The main contribution of this paper is in adapting the well-established punching and blanking operations to the meso-scale as a viable alternative to making miniature devices currently dominated by lithography-based techniques.     

Natural gas engine driven heat pump system – a case study of an office building

ABSTRACT

An eQUEST model was developed to conduct a simulation study of a natural gas engine-driven heat pump (GEHP) for an office building in Woodstock, Ontario, Canada. Prior to the installation of the GEHP, the heating and cooling demands of the office building were provided by rooftop units (RTUs), comprising of natural gas heater and electric air conditioner. Energy consumption for both GEHP and RTUs were monitored for operation in alternating months. These recorded energy consumptions along with weather data were used in the regression analysis. The developed eQUEST models were validated and calibrated with the regression analysis results with respect to the ASHRAE Guideline 14–2014. The eventual models were then applied to investigate the potential annual energy consumption, greenhouse gas (GHG) emission and energy cost savings achieved by using the GEHP in Woodstock, and other cities in Canada, particularly in Ontario.     

Development of a microscale emission factor model for particulate matter for predicting real-time motor vehicle emissions

The U.S. Environmental Protection Agency's National Exposure Research Laboratory is pursuing a project to improve the methodology for modeling human exposure to motor vehicle emissions. The overall project goal is to develop improved methods for modeling the source through the air pathway to human exposure in significant exposure microenvironments. Current particulate matter (PM) emission models, particle emission factor model (used in the United States, except California) and motor vehicle emission factor model (used in California only), are suitable only for county-scale modeling and emission inventories. There is a need to develop a site-specific real-time emission factor model for PM emissions to support human exposure studies near roadways. A microscale emission factor model for predicting site-specific real-time motor vehicle PM (MicroFacPM) emissions for total suspended PM, PM less than 10 microm aerodynamic diameter, and PM less than 2.5 microm aerodynamic diameter has been developed. The algorithm used to calculate emission factors in MicroFacPM is disaggregated, and emission factors are calculated from a real-time fleet, rather than from a fleet-wide average estimated by a vehicle-miles-traveled weighting of the emission factors for different vehicle classes. MicroFacPM requires input information necessary to characterize the site-specific real-time fleet being modeled. Other variables required include average vehicle speed, time and day of the year, ambient temperature, and relative humidity.     

GIS-based impact assessment and spatial distribution of air and water pollutants in mining area

Environmental Science and Pollution Research - Mining is a significant part of the transforming economy, which is generally considered as essential as well as social evil at the same time. It is...     

Estimating sampling frequency in pollen exposure assessment over time

A time series model was fitted to the pollen concentration data collected in the Greater Cincinnati area for the Cincinnati Childhood Allergy and Air Pollution Study (CCAAPS). A traditional time series analysis and temporal variogram approach were applied to the regularly spaced databases (collected in 2003) and irregularly spaced ones (collected in 2002), respectively. The aim was to evaluate the effect of the sampling frequency on the sampling precision in terms of inverse of standard error of the overall level of mean value across time. The presence of high autocorrelation in the data was confirmed and indicated some degree of temporal redundancy in the pollen concentration data. Therefore, it was suggested that sampling frequency could be reduced from once a day to once every several days without a major loss of sampling precision of the overall mean over time. Considering the trade-offs between sampling frequency and the possibility of sampling bias increasing with larger sampling interval, we recommend that the sampling interval should take values from 3 to 5 days for the pollen monitoring program, if the goal is to track the long-term average.