The geographic distribution and economic value of climate change-related ozone health impacts in the United States in 2030

In this United States-focused analysis we use outputs from two general circulation models (GCMs) driven by different greenhouse gas forcing scenarios as inputs to regional climate and chemical transport models to investigate potential changes in near-term U.S. air quality due to climate change. We conduct multiyear simulations to account for interannual variability and characterize the near-term influence of a changing climate on tropospheric ozone-related health impacts near the year 2030, which is a policy-relevant time frame that is subject to fewer uncertainties than other approaches employed in the literature. We adopt a 2030 emissions inventory that accounts for fully implementing anthropogenic emissions controls required by federal, state, and/or local policies, which is projected to strongly influence future ozone levels. We quantify a comprehensive suite of ozone-related mortality and morbidity impacts including emergency department visits, hospital admissions, acute respiratory symptoms, and lost school days, and estimate the economic value of these impacts. Both GCMs project average daily maximum temperature to increase by 1–4°C and 1–5 ppb increases in daily 8-hr maximum ozone at 2030, though each climate scenario produces ozone levels that vary greatly over space and time. We estimate tens to thousands of additional ozone-related premature deaths and illnesses per year for these two scenarios and calculate an economic burden of these health outcomes of hundreds of millions to tens of billions of U.S. dollars (2010$).

Implications:?Near-term changes to the climate have the potential to greatly affect ground-level ozone. Using a 2030 emission inventory with regional climate fields downscaled from two general circulation models, we project mean temperature increases of 1 to 4°C and climate-driven mean daily 8-hr maximum ozone increases of 1–5 ppb, though each climate scenario produces ozone levels that vary significantly over space and time. These increased ozone levels are estimated to result in tens to thousands of ozone-related premature deaths and illnesses per year and an economic burden of hundreds of millions to tens of billions of U.S. dollars (2010$).     

Evaluation of a Statewide Matching Grant Program for the Collection of Household Hazardous Waste

Between Fall 1985 and Spring 1987, the Massachusetts Departments of Environmental Management and Environmental Quality Engineering awarded communities $490,000 in matching state grants for the collection of household hazardous waste. Funded collections resulted in the disposal of approximately 291 tons of waste at an average cost of $9 per gallon. Household participation rates ranged from 0.2 percent to 5.8 percent. An average of 10 gallons of household hazardous waste was disposed of per participating household. Total collection costs including local and state shares exceeded $900,000. Differences in participation, wastes collected and collection costs among communities were due to variations in outreach and education efforts, experience, bid specifications, wastes collected, setup costs, and collection techniques. The relative high cost per participating household and low participation rate suggest the need for alternative approaches to the management of household hazardous waste which will be explored in future grant cycles.     

Waste Streams,Technology, and State Requirements

Biomedical wastes are generated by hospitals, laboratories, animal research facilities, and by other institutional sources. The disposal of these wastes is coming under critical public scrutiny, and regulations are being promulgated to control their disposal. Incineration is not a final disposal method since it generates a solid residue (ash) which must be buried or otherwise disposed. The incineration process, however, renders the waste non-toxic, non-hazardous, and non-putrescible, and reduces the volume of material for ultimate disposal by an order of magnitude. In some instances, the residue may have high levels of heavy metals; however, this is the exception rather than the rule.     

Mercury Measurement and Its Control: What We Know,Have Learned,and Need to Further Investigate

ABSTRACT

Based on the available evidence of health effects, the U.S. Environmental Protection Agency (EPA) has been evaluating the need to regulate mercury releases to the environment. In response to the congressional mandates in The 1990 Clean Air Act Amendments (CAAA), the EPA has issued the Mercury Study Report and the Study of Hazardous Air Pollutant Emissions from Electric Utility Steam Generating Units Report. In spite of the enormous effort represented by these reports, as well as the efforts of both the U.S. Department of Energy (DOE) and the Electric Power Research Institute (EPRI), in conducting the field measurement programs that form the basis for these reports, a definitive answer on the need for mercury regulation has not been found. However, the EPA, as well as other regulatory agencies and health researchers, have suggested a “plausible link” between anthropogenic sources emitting mercury and the methylation, bioaccumulation in the food chain, and adverse health effects in humans and wildlife.

Policy-makers have recognized that regulations must be based on good science and that a number of issues still remain. These issues can generally be grouped into four main categories: emissions inventory, control technology, fate of releases, and health effects. This paper will discuss recent, ongoing, and planned studies to address the remaining issues regarding the presence of mercury in the environment, with an emphasis on those studies that are directly related to the DOE/Federal Energy Technology Center’s (FETC) programmatic effort.     

The release of lindane from contaminated building materials

The release of the organochlorine pesticide lindane (γ-hexachlorocyclohexane) from several types of contaminated building materials was studied to assess inhalation hazard and decontamination requirements in response to accidental and/or intentional spills. The materials included glass, polypropylene carpet, latex-painted drywall, ceramic tiles, vinyl floor tiles, and gypsum ceiling tiles. For each surface concentration, an equilibrium concentration was determined in the vapour phase of the surrounding air. Vapor concentrations depended upon initial surface concentration, temperature, and type of building material. A time-weighted average (TWA) concentration in the air was used to quantify the health risk associated with the inhalation of lindane vapors. Transformation products of lindane, namely α-hexachlorocyclohexane and pentachlorocyclohexene, were detected in the vapour phase at both temperatures and for all of the test materials. Their formation was greater on glass and ceramic tiles, compared to other building materials. An empiric Sips isotherm model was employed to approximate experimental results and to estimate the release of lindane and its transformation products. This helped determine the extent of decontamination required to reduce the surface concentrations of lindane to the levels corresponding to vapor concentrations below TWA.     

Spatial trends of organochlorinated pesticides,polychlorinated biphenyls,and polybrominated diphenyl ethers in Atlantic Anguillid eels

The bioaccumulation of lipophilic contaminants such as polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), and polybrominated diphenyl ethers (PBDEs) can result in a reduction in fitness and spawner quality in eels and may be a factor in Anguillid sp. population declines. Contaminant concentrations in eels have been studied extensively in Europe, but data for American eels are severely lacking. Concentrations of PCBs, OCPs, and PBDEs were determined in American eel from eastern Canada and New York, USA, along with European eel from Belgium. Principal component analysis revealed that eels captured in the St. Lawrence estuary were a mixture of upstream migrants from the St. Lawrence River watershed, and fish captured in local tributaries. Contaminant concentrations were dependent on origin, related to the local environment, and were lower than historic values. In Canada, concentrations of OCPs and PCBs in eel tissues were below the Canadian human consumption guidelines for contaminants in fish, indicating that the current risk to consumers is low. However, concentrations of PCBs, total DDT, and mirex in eels from L. Ontario and the upper St. Lawrence R. were above Great Lakes guidelines for the protection of piscivorous predators. Concentrations of penta-BDE homologs exceeded the Canadian guideline for environmental quality in over half of the eels in this study, but concentrations of the other homolog groups were below the guideline.     

Assessment of pumped mercury vapour adsorption tubes as passive samplers using a micro-exposure chamber

Mercury vapour adsorption tubes manufactured for pumped sampling and analysis have been evaluated for their performance as passive samplers. This has been done by exposing these tubes in a novel micro-exposure chamber. The uptake rates of these tubes have been found to be low (approximately 0.215 ml min(-1)) as compared to bespoke passive samplers for mercury vapour (typically in excess of 50 ml min(-1)). The measured uptake rates were shown to vary significantly between tubes and this was attributed to the variability in the air-sorbent interface and the proportion of the cross sectional area removed by the crimp in the quartz tubes used to secure the sorbent material. As a result of this variability the uptake rate of each tube must be determined using the micro-exposure chamber prior to deployment. Results have shown that the uptake rate determined in the micro-exposure chamber is invariant of concentration, and therefore these uptakes rates may be determined at a high mercury vapour concentration for many tubes at once in less than one hour. The uptake rate of the adsorption tubes under these conditions may be determined with a precision of 5%. Measurements made on a limited field trial in indoor and outdoor ambient air have shown that these tubes give results in acceptable agreement with more traditional pumped sampling methods, although longer sampling periods are required in order to reduce the uncertainty of the measurement, which is currently approximately 30%.     

Correspondence of biological condition models of California streams at statewide and regional scales

We used boosted regression trees (BRT) to model stream biological condition as measured by benthic macroinvertebrate taxonomic completeness, the ratio of observed to expected (O/E) taxa. Models were developed with and without exclusion of rare taxa at a site. BRT models are robust, requiring few assumptions compared with traditional modeling techniques such as multiple linear regression. The BRT models were constructed to provide baseline support to stressor delineation by identifying natural physiographic and human land use gradients affecting stream biological condition statewide and for eight ecological regions within the state, as part of the development of numerical biological objectives for California’s wadeable streams. Regions were defined on the basis of ecological, hydrologic, and jurisdictional factors and roughly corresponded with ecoregions. Physiographic and land use variables were derived from geographic information system coverages. The model for the entire state (n?=?1,386) identified a composite measure of anthropogenic disturbance (the sum of urban, agricultural, and unmanaged roadside vegetation land cover) within the local watershed as the most important variable, explaining 56 % of the variance in O/E values. Models for individual regions explained between 51 and 84 % of the variance in O/E values. Measures of human disturbance were important in the three coastal regions. In the South Coast and Coastal Chaparral, local watershed measures of urbanization were the most important variables related to biological condition, while in the North Coast the composite measure of human disturbance at the watershed scale was most important. In the two mountain regions, natural gradients were most important, including slope, precipitation, and temperature. The remaining three regions had relatively small sample sizes (n?≤?75 sites) and had models that gave mixed results. Understanding the spatial scale at which land use and land cover affect taxonomic completeness is imperative for sound management. Our results suggest that invertebrate taxonomic completeness is affected by human disturbance at the statewide and regional levels, with some differences among regions in the importance of natural gradients and types of human disturbance. The construction and application of models similar to the ones presented here could be useful in the planning and prioritization of actions for protection and conservation of biodiversity in California streams.     

Technological options for the management of biosolids

BACKGROUND, AIM, AND SCOPE: Large quantities of biosolids (sewage sludge), which are produced from municipal wastewater treatment, are ever-increasing because of the commissioning of new treatment plants and continuous upgrades of the existing facilities. A large proportion of biosolids are currently landfilled. With increasing pressure from regulators and the general public, landfilling of biosolids is being phased out in many countries because of potential secondary pollution caused by leachate and the emission of methane, a potent greenhouse gas. Biosolids contain nutrients and energy that can be used beneficially. Significant efforts have been made recently to develop new technologies to manage biosolids and make useful products from them. In this paper, we provide a review of the technologies in biosolids management. MATERIALS AND METHODS: A survey of literature was conducted. RESULTS: At present, the most common beneficial use of biosolids is agricultural land application because of inherent fertilizer values found in biosolids. Expansion of land application, however, may be limited in the future because of more stringent regulatory requirements and public concern about food chain contamination in some countries. Perceived as a green energy source, the combustion of biosolids has received renewed interest. Anaerobic digestion is generally a more effective method than incineration for energy recovery, and digested biosolids are suitable for further beneficial use through land application. Although conventional incineration systems for biosolid management generally consume more energy than they produce because of the high moisture content in the biosolids, it is expected that more combustion systems, either monocombustion or cocombustion, will be built to cope with the increasing quantity of biosolids. DISCUSSION: Under the increasingly popular low-carbon economy policy, biosolids may be recognized as a renewable fuel and be eligible for 'carbon credits'. Because ash can be used to manufacture construction materials, combustion can provide a complete management for biosolids. A number of advanced thermal conversion technologies (e.g., supercritical water oxidation process and pyrolysis) are under development for biosolids management with a goal to generate useful products, such as higher quality fuels and recovery of phosphorus. With an ever-increasing demand for renewable energy, growing bioenergy crops and forests using biosolids as a fertilizer and soil amendment can not only contribute to the low-carbon economy but also maximize the nutrient and carbon value of the biosolids. CONCLUSIONS: Land application of biosolids achieves a complete reuse of its nutrients and organic carbon at a relatively low cost. Therefore, land application should become a preferred management option where there is available land, the quality of biosolids meet regulatory requirements, and it is socially acceptable. Intensive energy cropping and forest production using biosolids can help us meet the ever-increasing demand for renewable energy, which can eliminate the contamination potential for food sources, a common social concern about land application of biosolids. In recent years, increasing numbers of national and local governments have adopted more stringent regulations toward biosolid management. Under such a political climate, biosolids producers will have to develop multireuse strategies for biosolids to avoid being caught because a single route management practice might be under pressure at a short notice. Conventional incineration systems for biosolids management generally consume more energy than they produce and, although by-products may be used in manufacturing, this process cannot be regarded as a beneficial use of biosolids. However, biosolids are likely to become a source of renewable energy and produce 'carbon credits' under the increasingly popular, low-carbon economy policy. RECOMMENDATIONS AND PERSPECTIVES: To manage biosolids in a sustainable manner, there is a need for further research in the following areas: achieving a higher degree of public understanding and acceptance for the beneficial use of biosolids, developing cost-efficient and effective thermal conversions for direct energy recovery from biosolids, advancing technology for phosphorus recovery, and selecting or breeding crops for efficient biofuel production.     

Use of diammonium phosphate to reduce heavy metal solubility and transport in smelter-contaminated soil

Phosphate treatments can reduce metal dissolution and transport from contaminated soils. However, diammonium phosphate (DAP) has not been extensively tested as a chemical immobilization treatment. This study was conducted to evaluate DAP as a chemical immobilization treatment and to investigate potential solids controlling metal solubility in DAP-amended soils. Soil contaminated with Cd, Pb, Zn, and As was collected from a former smelter site. The DAP treatments of 460, 920, and 2300 mg P kg-1 and an untreated check were evaluated using solute transport experiments. Increasing DAP decreased total metal transported. Application of 2300 mg P kg-1 was the most effective for immobilizing Cd, Pb, and Zn eluted from the contaminated soil. Metal elution curves fitted with a transport model showed that DAP treatment increased retardation (R) 2-fold for Cd, 6-fold for Zn, and 3.5-fold for Pb. Distribution coefficients (Kd) increased with P application from 4.0 to 9.0 L kg-1 for Cd, from 2.9 to 10.8 L kg-1 for Pb, and from 2.5 to 17.1 L kg-1 for Zn. Increased Kd values with additional DAP treatment indicated reduced partitioning of sorbed and/or precipitated metal released to mobile metal phases and a concomitant decrease in the concentration of mobile heavy metal species. Activity-ratio diagrams indicated that DAP decreased solution Cd, Pb, and Zn by forming metal-phosphate precipitates with low solubility products. These results suggest that DAP may have potential for protecting water resources from heavy metal contamination near smelting and mining sites.