Numerical Model Inter-comparison for Wind Flow and Turbulence Around Single-Block Buildings

Wind flow and turbulence within the urban canopy layer can influence the heating and ventilation of buildings, affecting the health and comfort of pedestrians, commuters and building occupants. In addition, the predictive capability of pollutant dispersion models is heavily dependent on wind flow models. For that reason, well-validated microscale models are needed for the simulation of wind fields within built-up urban microenvironments. To address this need, an inter-comparison study of several such models was carried out within the European research network ATREUS. This work was conducted as part of an evaluation study for microscale numerical models, so they could be further implemented to provide reliable wind fields for building energy simulation and pollutant dispersion codes. Four computational fluid dynamics (CFD) models (CHENSI, MIMO, VADIS and FLUENT) were applied to reduced-scale single-block buildings, for which quality-assured and fully documented experimental data were obtained. Simulated wind and turbulence fields around two surface-mounted cubes of different dimensions and wall roughness were compared against experimental data produced in the wind tunnels of the Meteorological Institute of Hamburg University under different inflow and boundary conditions. The models reproduced reasonably well the general flow patterns around the single-block buildings, although over-predictions of the turbulent kinetic energy were observed near stagnation points in the upwind impingement region. Certain discrepancies between the CFD models were also identified and interpreted. Finally, some general recommendations for CFD model evaluation and use in environmental applications are presented.     

Particle-bound polycyclic aromatic hydrocarbons in an urban, industrial and rural area in the western Mediterranean

Particle-bound PAHs were measured at three sites in southeastern Spain (an urban background location, a suburban-industrial site in the vicinity of two cement plants and a rural area) in order to investigate the influence of the type of location on PAH concentrations. A clear influence of cement production on particulate PAH levels could not be established since for the urban background and suburban-industrial sites the average concentrations of total PAHs in the PM2.5 fraction were very similar (1.085 and 1.151 ng m(-3), respectively), with benzo[b+k]fluoranthene and chrysene as the predominant compounds. Diagnostic ratios, used to identify PAH emission sources, pointed to traffic as the main source of particulate PAH at both locations. As expected, PAH levels at the rural site were significantly lower (0.408 ng m(-3) in the PM10 fraction) due to increasing distance from the emission sources. PAH seasonal variations at the urban background and suburban-industrial sites were the same as reported in many previous studies. Average winter to summer ratios for total PAHs were 4.4 and 4.9 for the urban background and industrial sites, in that order. This seasonal cycle could be partially explained by the higher temperature and solar radiation during summer enhancing PAH evaporation from the particulate phase and PAH photochemical degradation, respectively. The study of PAH distribution between the fine and coarse fraction at the urban site revealed that on average around 80% of total PAHs were associated with fine particles.     

Enterprise-Level Motivations,Regulatory Pressures,and Corporate Environmental Management in Guangzhou,China

This study examines the effects of internal motivations and external pressures on the integration of environmental management (EM) practices within manufacturing operations in China. The moderating role of perceptions toward the regulatory process is also considered along with comparisons between wholly Chinese-owned and foreign-owned enterprises. From a sample of 131 manufacturing companies in the Guangzhou area, it was found that the salience of fees and fines has a strong positive influence on perceptions toward the regulator (the local Environmental Protection Bureau, EPB). This also has a positive effect on perceptions toward regulations themselves for foreign-owned enterprises. Business-case motivations for EM positively shape enterprise perceptions toward regulations, whereas risk-reduction motivations have a negative effect on perceptions toward regulations in foreign-owned enterprises. Enterprise perceptions toward the regulatory process have direct effects on the integration of EM practices in wholly Chinese-owned enterprises, but in opposite directions. While positive perceptions toward regulations have positive influence, positive perceptions toward regulators (i.e., the EPB) negatively affect it. Overall, these results indicated that promoting the adoption of EM practices depends on convincing business leaders that EM practices contribute to profit making. The regulatory process can potentially promote these practices, but measures need to be taken to ensure that the regulator is not co-opted by the regulated, especially in wholly Chinese-owned enterprises.     

Efficient management capacity evaluation of tourism in protected areas

Despite the increasing number of protected areas around the world and their importance in the conservation of species and ecosystems, protected areas management capacity remains difficult to evaluate. A standard is needed to help policy makers compare the goals with the results obtained. This empirical research builds a tool to analyze the management efficiency and predicts the new touristic outcomes in case of a policy change. Using as example the state parks agencies in the USA, this paper develops a technological frontier using data envelopment analysis based on the Protected Areas Management Approach. After that, a prediction of the outcomes is analyzed with a budget change for any state park agency. Data suggest that many of them need to improve their performance to be more efficient. Another result obtained shows how budget changes will affect each agency's performance in different degrees and, therefore, budget reductions should be modeled separately.     

Degradation of 2,4,6-trichlorophenol in aqueous systems through the association of zero-valent-copper-mediated reduction and UVC/H2O2: effect of water matrix and toxicity assessment

Environmental Science and Pollution Research - The presence of toxic chlorinated compounds in drinking water, generated during the disinfection step in water treatment plants, is of great concern...     

A comprehensive dynamic kinetic model for the UVC/H2O2 process: application to zinc bacitracin degradation in wastewater as a case study

Environmental Science and Pollution Research - A dynamic kinetic model is presented for the UVC/H2O2-driven process. The model comprises 103 reactions, including background species, such as...     

Mercury removal using ground and calcined mussel shell

We determined mercury retention on calcined and ground mussel shell, in presence and absence of phosphate, using batch and stirred flow chamber experiments. In batch experiments the calcined shell exhibited higher Hg adsorption, with good fitting to Freundlich equation （R^2： 0.925-0.978）; the presence of phosphate increased Hg adsorption; mercury desorption was 13% or lower, diminishing up to 2% under the presence of phosphates. In stirred flow chamber experiments calcined shell retained more Hg than ground shells （6300 vs. 4000-5200 μmol/kg）; Hg retention increased an additional 40% on calcined shell and up to an additional 70% on ground shells when phosphates were present; mercury desorption was quite similar in all shell types （20%-34%）, increasing up to 49%-60% in ground shells when phosphates were present. The higher Hg adsorption on calcined shell would be related to its calcite and dolomite concentrations; mercury-phosphate interactions would cause the increase in Hg retention when phosphates are present. Data on Hg desorption suggest that Hg retention was not easily reversible after batch experiments, increasing in the stirred flow chamber due to convective flow. Calcined and ground mussel shells could be recycled removing Hg from water, with the presence of phosphates in solution improving efficacy.     

Recycling of iron foundry sand and glass waste as raw material for production of whiteware.

The purpose of this study was to evaluate the production feasibility of triaxial whiteware using sand from cast iron moulds as a raw material instead of silica, and recycled glass in place of feldspar. Formulations were prepared using sand, glass waste, and white-firing clay such that only 50% of the composition was virgin material (clay). The ceramic bodies were formed by pressing and fired at different temperatures (between 1100 and 1300 degrees C). Specimens were characterized in terms of green density prior to firing; and their flexural strength, linear shrinkage, and water absorption were measured after firing. The microstructure was determined by scanning electron microscopy. Possible environmental impacts of this recycling process were also evaluated, through solubility and leaching tests, according to Brazilian standards. Gaseous emissions during the firing process were also analysed. The results showed that it is possible to produce triaxial ceramics by using such alternative raw materials.