表面活性剂增效电动技术修复多环芳烃污染土壤

研究了电动修复过程中修复时间和表面活性剂Triton X-100、鼠李糖脂对多环芳烃芘污染土壤的修复效果的影响。结果表明,在电动修复过程中,随着修复时间的增加,芘的去除率相应提高。通过向电解液中添加表面活性剂Triton X-100,芘的去除率从11.64%提高到了23.42%,当在电解液中添加浓度为40倍CMC的鼠李糖脂后去除率升高至36.29%,阳极附近土壤甚至达到了92.49%,这表明Triton X-100和鼠李糖脂均能促进土壤中芘的溶解和迁移,鼠李糖脂的促进作用高于Triton X-100。     

强化除磷型A/O-MBR工艺运行稳定性

采用缺氧/好氧膜生物反应器(A/O-MBR)处理合成的生活污水,考察了投加不同浓度的聚合氯化铝(PAC)对该工艺在除磷效能及运行稳定性方面的影响。结果表明,投加PAC可以有效降低出水TP的浓度;在投加量为150 mg/L时,TP的去除率达到最优,为90.1%,出水浓度维持0.48 mg/L左右,达到《城镇污水处理厂污染物排放标准》(GB18918-2002)的一级A标准。投加一定量的PAC可以有效提高微生物的活性;此外,可以降低污泥絮体的Zeta电位,增大污泥絮体的粒径,降低胞外聚合物(EPS)中多糖的浓度,进而有效延缓膜污染的速率。     

芦苇碳源-表面流人工湿地对农田退水脱氮的长期效能研究

针对农田退水NO₃^--N占比高、C/N低,氮污染难以去除的问题,将经济易得的芦苇(Phragmites australis)茎叶碎段装填在表面流人工湿地(packed surface flow construct wetland,PSFW)的表层作为外加碳源,以研究其长期运行情况下的脱氮效能。结果表明：第29~149天,外加芦苇茎叶碎段的PSFW的脱氮效能明显高于无芦苇茎叶碎段的空白PSFW₀;进水NO₃^--N和TN浓度分别为(16.4±1.0)和(17.7±2.0)mg/L,HRT按3、4和2 d运行时,HRT为4 d时脱氮效能最优,PSFW对NO₃^--N和TN去除率分别为(87.4±6.0)%和(74.1±6.0)%,PSFW₀去除率仅为(14.4±4.0)%和(14.4±3.0)%;第150~269天,PSFW的脱氮效能稍高于PSFW₀,在进水NO₃^--N和TN浓度分别为(10.4±1.0)和(10.8±1.0)mg/L,HRT按3、2和1 d运行时,HRT为3 d时脱氮效能最优,PSFW对NO₃^--N和TN的去除率分别为(91.9±7.0)%和(90.2±7.0)%,PSFW₀去除率分别为(91.3±5.0)%和(86.4±6.0)%。第270~334天,PSFW的脱氮效能稍低于PSFW₀;进水NO₃^--N和TN浓度分别为(5.7±0.4)和(7.2±0.8)mg/L,HRT为3 d时,PSFW对NO₃^--N和TN的去除率分别为(88.6±10.0)%和(82.5±7.0)%,PSFW₀去除率分别为(94.0±6.0)%和(87.8±3.0)%。     

Effects of leachate accumulation on landfill stability in humid regions of China

Leachate levels are important to landfill stability and safety. High leachate or water levels often lead to landfill instability, which can cause accidents. Here a case study of a landfill located in a humid region of southern China is presented. Leachate distribution and quality were systematically analyzed, and the effect of leachate level on waste-mass stability was assessed. Boreholes were drilled in the field, samples were analyzed in the laboratory, and a simulation was performed. In addition, the safety and stability of the landfill was evaluated. The leachate level in the landfill was 9–19 m, which was higher than the top of the dam crest (8–20 m). Leachate accounted for more than 1/4 of the total landfill storage capacity. The contaminant concentration of the leachate samples collected directly from the waste body was very high, with large variation among the samples. The mean concentrations of NH₃–N, BOD, and COD from the waste body were 5404, 14,136, and 22,691 mg/L, nearly 2.7, 2.4, and 1.8 times the mean concentrations in the leachate pond, respectively. Three series of shear strength parameters were used in a slope stability analysis, and a limit equilibrium method was used to calculate the factor of safety (Fs). The analysis showed that Fs could be affected by potential anisotropy in the shear strength of the waste. The minimum values of Fs corresponding to series I were 1.84 and 1.17 for units ? and II, respectively. The Fs value of unit II was significantly lower than the safe design value (1.25). In addition, Fs decreased with increase in the normalized height of the leachate level, h/H, where h is the height of the leachate mound and H is the maximum thickness of the landfill. If the h/H values of units I and II are kept below 50% and 40%, respectively, a safe design value of 1.25 for Fs can be guaranteed. Therefore, some measures to prevent risk should be considered.     

大气气溶胶中元素种态研究

应用化学逐级提取流程对国际原子能机构（简称IAEA）气溶胶、室内和室外气溶胶、煤飞灰中元素的组成和种态进行了分析,应用仪器中子活化法测定了各种态中元素的含量,计算出元素在各种态中的分配比例。按照气溶胶中元素不同种态的环境和生物活性以及主要来源来分类,评述了元素在环境和生态系统中的吸收和转化能力,并对气溶胶中元素对环境的影响作出了初步的探讨。实验数据表明,气溶胶中的不同元素在各种态中的分布是有差异的。地壳来源元素中,Sc,Al,Fe和Ti主要分布在不溶物态中,稀土元素主要分布在氧化物态和不溶物态;不溶物态沉降到地表后不易进行迁移和转化,对环境的影响较小;氧化物态性质比较活泼,可以在大气中发生化学反应。Mn在气溶胶中主要分布在水可溶态和氧化物态,环境可交换性要比Al,Fe,Ti等大得多。人为来源元素的环境可交换态的比例都比较高,这说明它们通过干、湿清除过程沉降到地表后,水可溶态可以直接进入水循环;碳酸盐、氧化物和有机物态可以在适当的条件下与环境中的其他物质发生化学反应,生成易溶于水的化合物进入生态环境中,对环境影响较大。     

生物炭/铁酸镧磁性复合材料的制备及对亚甲基蓝的吸附性能

为获得吸附性能良好、便于回收利用的新型吸附剂以处理染料废水,采用超声辅助溶胶-凝胶法将铁酸镧(LaFeO_3)经过一步热解负载于生物炭制得生物炭/LaFeO_3磁性复合材料(BC/FL)。其表面形态、结构和组成分析表明:BC/FL的比表面积、总孔容及平均孔径分别为34.67m2/g、0.041cm3/g和7.82nm,磁饱和强度达到40.283A/m,表面含有C=O、C=C=N、C≡C等官能团。批量吸附实验表明,25℃下,当亚甲基蓝(MB)的初始质量浓度为30mg/L时,BC/FL的最佳投加量为1.5g/L,吸附反应在120min达到平衡,去除率可达92.3%,且吸附效果基本不受pH影响。BC/FL对MB的吸附符合准二级动力学模型,Langmuir模型可描述其等温吸附过程。化学吸附占主导地位,主要机理为静电吸附、氢键和π-π共轭作用。吸附反应为单分子层吸附且为自发的吸热过程。     

Biodegradation of phthalate esters by two bacteria strains

In this study two aerobic phthalic acid ester (PAE) degrading bacteria strains, DK4 and O18, were isolated from river sediment and petrochemical sludge, respectively. The two strains were found to rapidly degrade PAE with shorter alkyl-chains such diethyl phthalate (DEP), dipropyl phthalate (DPrP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP) and diphenyl phthalate (DPP) are very easily biodegraded, while PAE with longer alkyl-chains such as dicyclohexyl phthalate (DCP) and dihexyl phthalate (DHP) and di-(2-ethylhexyl) phthalate (DEHP) are poorly degraded. The degradation rates of the eight PAEs were higher for strain DK4 than for strain O18. In the simultaneous presence of strains DK4 and O18, the degradation rates of the eight PAEs examined were enhanced. When the eight PAEs were present simultaneously, degradation rates were also enhanced. We also found that PAE degradation was delayed by the addition of nonylphenol or selected polycyclic aromatic hydrocarbons (PAHs) at a concentration of 1 microg/g in the sediment. The bacteria strains isolated, DK4 and O18, were identified as Sphigomonas sp. and Corynebacterium sp., respectively.     

Reactions of compost-derived humic substances with lead, copper, cadmium, and zinc

Thermodynamic stability constants of the formation of complexes from the reactions of humic substances with various metals are usually used as parameters to judge the reactivities of both humic substances and metals. However, in calculating the thermodynamic stability constants, complicated processes for the acquisition of activities of components in reactions are absolutely inevitable. In this study, we investigated the average conditional concentration quotients of the complexes formed from the reaction of metals with humic substances and the relations of these quotients to thermodynamic stability constants. The characterized humic substances including HA (MW>1,000), FA (MW>1,000), and FA (MW<1,000) extracted from a swine compost were prepared to react with Pb, Cu, Cd, and Zn at 25 degrees C and at pH 4.00 and 6.50. Reactions of HA (MW>1,000), FA (MW>1,000), and FA (MW<1,000) with the four metals were carried out at 1:0.1, 1:0.5, 1:1, 1:5, and 1:10 ligand:metal stoichiometry. The concentrations of the free ions of Pb, Cu, Cd, and Zn in the reaction systems of metal-HA suspensions and metal-FA solutions were measured by anodic stripping voltammetry (ASV). The sequence of the average conditional concentration quotients of the formed complexes from the reaction of humic substances with metals was FA(MW<1,000)>FA(MW>1,000)>HA(MW>1,000), showing the relative reactivities of the fractions of swine compost-derived humic substances. The sequence of reacting metals with humic substances was Pb>Cu>Cd>Zn, which is in good agreement with the sequence reported by judging the thermodynamic stability constants. The average conditional concentration quotients of the formed complexes from the reaction of humic substances with metals were thus useful parameters that can be directly related to thermodynamic stability constants and other parameters.     

Emission of PCDD/Fs and dioxin-like PCBs from metallurgy industries in S. Korea

The metallurgy industry and municipal waste incinerators are considered the main sources of polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs) in many countries. This study investigated the emission factors and total emissions of PCDD/Fs and dioxin-like polychlorinated biphenyls (PCBs) emitted from metallurgy industries (including ferrous and nonferrous foundries) in Korea. The toxic equivalency (TEQ) emission factor of PCDD/Fs was the highest for secondary copper production, at 24451 ng I-TEQ/ton. The total estimated emissions of PCDD/Fs from these sources were 35.259 g I-TEQ/yr, comprising 0.088 g I-TEQ/yr from ferrous foundries, 31.713 g I-TEQ/yr from copper production, 1.716 g I-TEQ/yr from lead production, 0.111 g I-TEQ/yr from zinc production, and 1.631 g I-TEQ/yr from aluminum production. The total estimated annual amounts of dioxin-like PCBs emitted from these sources were 13.260 g WHO-TEQ/yr, comprising 0.014 g WHO-TEQ/yr from ferrous foundries, 12.675 g WHO-TEQ/yr from copper production, 0.170 g WHO-TEQ/yr from lead production, 0.017 g WHO-TEQ/yr from zinc production, and 0.384 g WHO-TEQ/yr from aluminum production. The highest emission factor was found for secondary copper smelting, at 9770 ng WHO-TEQ/ton.     

Characteristics of fungal flora in onion farmlands with potential link to human mycotic keratitis

Acquisition of mycotic keratitis has been linked to agricultural activities. Although fungi were identified in injured eyes, data derived directly from farmlands are limited. Following five cases of fungal corneal ulcers in onion harvesters in the monsoon area of Taiwan, the present study further determined fungi genera and their concentrations in onion crops and surface soils of onion farmlands. In total, 52, 100 and 100 samples of soils, onion leaves and bulb scales, respectively, were collected from three monsoon and one non-monsoon farmlands. Fungal colonies were counted and microscopically examined after incubation at 25°C for 4–7 days on malt extract agar with 40?g?mL^?1 chloramphenicol. Results showed the peak fungi levels were mostly observed at harvest time. Among keratitis-related fungi, Aspergillus predominated in soils as well as in onion bulb scales, while Alternaria in onion leaves. Cladosporium was also prevalent in soils, onion leaves and scales. Other keratitis-related fungi included Acremonium, Curvalaria, Fusarium, Mycelia, Penicillium, Rhizoctonia and Rhizopus. The present study provides an exposure link between onion harvesters and presence of keratitis-related fungi from onion crops and soils, which may account for mycotic ocular infection via hand-to-eye contact and airborne transmission during the monsoon season.