Leaded electronic waste is a possible source material for lead-contaminated jewelry

Highly leaded jewelry, often imported from China, remains widely available in the United States. Leaded electronic waste is exported from the United States to several Asian countries where solder is recovered and circuit boards are stripped of parts in small workshops. To assess whether electronic waste is being recycled into the jewelry, lead, tin and copper content of highly leaded jewelry samples were determined by atomic absorption spectrometry. Sixteen jewelry items previously determined to contain 20-80% lead by weight were analyzed. Samples were digested in nitric acid for analysis of lead and copper, and in aqua regia for analysis of tin. Six samples contained significant amounts of tin, from 20.8% to 29.9% by weight. In addition, copper was a significant minor component of five of these samples (up to 4% by weight). Copper (present at 10-40% by weight in circuit boards) was shown to rapidly move into heated lead-tin solder. The combined lead-tin-copper content of these six items ranges from 93.5% to 100%, suggestive of a solder-based source material. These results are consistent with the hypothesis that recycled circuit board solders are being used to produce some of the heavily leaded imported jewelry sold in the United States. Should this hypothesis be substantiated, it suggests that environmental policies to protect children's health must address both proper recycling of source materials as well as restrictions of the lead content in consumer goods.     

Well water contaminated by acidic mine water from the Dabaoshan Mine, south China: chemistry and toxicity

An investigation into well water quality was carried out in a rural area subject to irrigation with acidic mine water from the Guangdong Dabaoshan Mine, southern China. The results of water pH measurements from 112 wells in two different seasons suggest that the well water has been contaminated to varying degrees in the investigated Shangba floodplain (approximately 11km south of the Guangdong Dabaoshan Mine). There is a trend that well water pH increased southwards, suggesting that the impacts of acidic irrigation water on groundwater decreased with increasing distance to the entry point of acidic irrigation water. Water quality monitoring results of the selected wells show that Cu and Cd in the water exceeded the limits set in the Chinese National Standards for Drinking Water (GB 5749-85) for the wells close to the irrigation water source. If the World Health Organization (WHO) standard was considered, Cd in some wells was almost 10 times as high as the WHO guideline value (0.003mg l(-1)). Water collected from the location closest to the acidic irrigation water source was acutely toxic to the test organism (Daphnia carinata) even after 51 time dilution. It is likely that the extremely high mortality rate of the local population reported for the study area is at least partly related to the high levels of heavy metals, particularly Cd in the drinking well water.     

Leaching of seven pesticides currently used in cotton crop in Mato Grosso State-Brazil

This study aimed to evaluate the leaching of pesticides and the applicability of the Attenuation Factor (AF) Model to predict their leaching. The leaching of carbofuran, carbendazim, diuron, metolachlor, alpha and beta endosulfan and chlorpyrifos was studied in an Oxisol using a field experiment lysimeter located in Dom Aquino-Mato Grosso. The samples of percolated water were collected by rain event and analyzed. Chemical and physical soil attributes were determined before pesticide application to the plots. The results showed that carbofuran was the pesticide that presented a higher leaching rate in the studied soil, so was the one representing the highest contamination potential. From the total carbofuran applied in the soil surface, around 6% leached below 50 cm. The other pesticides showed lower mobility in the studied soil. The calculated values to AF were 7.06E-12 (carbendazim), 5.08E-03 (carbofuran), 3.12E-17 (diuron), 6.66E-345 (alpha-endosulfan), 1.47E-162 (beta-endosulfan), 1.50E-06 (metolachlor), 3.51E-155 (chlorpyrifos). AF Model was useful to classify the pesticides' potential for contamination; however, that model underestimated pesticide leaching.     

Techniques for the stabilization and assessment of treated copper-, chromium-, and arsenic-contaminated soil

Remediation mainly based on excavation and burial of the contaminated soil is impractical with regard to the large numbers of sites identified as being in need of remediation. Therefore, alternative methods are needed for brownfield remediation. This study was conducted to assess a chemical stabilization procedure of CCA-contaminated soil using iron (Fe)-containing blaster sand (BS) or oxygen-scarfing granulate (OSG). The stabilization technique was assessed with regard to the feasibility of mixing ameliorants at an industrial scale and the efficiency of the stabilization under different redox conditions. The stability was investigated under natural conditions in 1-m3 lysimeters in a field experiment, and the effect of redox conditions was assessed in a laboratory experiment (10 L). The treatments with high additions of ameliorant (8% and 17%) were more successful in both the laboratory and field experiments, even though there was enough Fe on a stochiometric basis even at the lowest addition rates (0.1% and 1%). The particle size of the Fe and the mixing influenced the stabilization efficiency. The development of anaerobic conditions, simulated by water saturation, increases the fraction of arsenic (AsIII) and, consequently, As mobility. The use of high concentrations of OSG under aerobic conditions increased the concentrations of nickel (Ni) and copper (Cu) in the pore water. However, under anaerobic conditions, it decreased the As leaching compared with the untreated soil, and Ni and Cu leaching was not critical. The final destination of the treated soil should govern the amendment choice, that is, an OSG concentration of approximately 10% may be suitable if the soil is to be landfilled under anaerobic conditions. Alternatively, the soil mixed with 1% BS could be kept under aerobic conditions in a landfill cover or in situ at a brownfield site. In addition, the treatment with BS appeared to produce better effects in the long term than treatment with OSG.     

Fugitive emissions opacity determination using the digital opacity compliance system (DOCS)

Maintenance of Department of Defense (DoD) weapon systems, conducting battlefield training exercises as well as meeting military construction and/or demolition schedules, invariably generate fugitive air emissions, many of which are visible. Although there is no codified federal method for quantifying fugitive emissions opacity, many state and local air regulatory agencies have instituted enforceable fugitive emission opacity standards at DoD facilities. The current study focused on comparing the performance of the digital opacity compliance system (DOCS) with U.S. Environment Protection Agency Method 9 (Method 9) certified human observers in quantifying the visible opacity associated with fugitive emissions produced using a commercial fog generator. By systematically repositioning both DOCS cameras and Method 9-certified observers during field testing, differences in method performance as a function of observational locations were documented. At both the 30- and 300-ft off-set distances, opacity levels reported by the DOCS technology and Method 9-certified smoke readers were found to be statistically different at the 99% confidence level. Alternatively, at the 90- and 150-ft off-set distances, results suggested that there was an insignificant difference at the 99% confidence level between the two methods. Comparing the magnitude of the each method's standard deviation suggested that, at the 30-ft off-set distance, the DOCS technology was consistently more precise than Method 9-certified readers regardless of the observer's downwind distance. However, at the 90, 150, and 300-ft off-set distances, method precision seemed to vary as a function of both off-set and downwind distance. The primary factor affecting the consistency in opacity measurements appeared to be the impact of ground-level air turbulence on fog plume dispersion and transport. Field observations demonstrated that localized wind shear played a critical and decisive role in how and to what extent fugitive emissions opacity could be determined, regardless of the method selected.     

A practical method for quantification of phosphorus- and glycogen-accumulating organism populations in activated sludge systems.

Enhanced biological phosphorus removal (EBPR) from wastewater relies on the enrichment of activated sludge with phosphorus-accumulating organisms (PAOs). The presence and proliferation of glycogen-accumulating organisms (GAOs), which compete for substrate with PAOs, may be detrimental for EBPR systems, leading to deterioration and, in extreme cases, failure of the process. Therefore, from both process evaluation and modeling perspectives, the estimation of PAO and GAO populations in activated sludge systems is a relevant issue. A simple method for the quantification of PAO and GAO population fractions in activated sludge systems is presented in this paper. To develop such a method, the activity observed in anaerobic batch tests executed with different PAO/GAO ratios, by mixing highly enriched PAO and GAO cultures, was studied. Strong correlations between PAO/GAO population ratios and biomass activity were observed (R2 > 0.97). This served as a basis for the proposal of a simple and practical method to quantify the PAO and GAO populations in activated sludge systems, based on commonly measured and reliable analytical parameters (i.e., mixed liquor suspended solids, acetate, and orthophosphate) without requiring molecular techniques. This method relies on the estimation of the total active biomass population under anaerobic conditions (PAO plus GAO populations), by measuring the maximum acetate uptake rate in the presence of excess acetate. Later, the PAO and GAO populations present in the activated sludge system can be estimated, by taking into account the PAO/GAO ratio calculated on the basis of the anaerobic phosphorus release-to-acetate consumed ratio. The proposed method was evaluated using activated sludge from municipal wastewater treatment plants. The results from the quantification performed following the proposed method were compared with direct population estimations carried out with fluorescence in situ hybridization analysis (determining Candidatus Accumulibacter Phosphatis as PAO and Candidatus Competibacter Phosphatis as GAO). The method showed to be potentially suitable to estimate the PAO and GAO populations regarding the total PAO-GAO biomass. It could be used, not only to evaluate the performance of EBPR systems, but also in the calibration of potential activated sludge mathematical models, regarding the PAO-GAO coexistence.     

Further studies on the uptake of persistent organic pollutants (POPs) by polyurethane foam disk passive air samplers

Passive air samplers (PAS) can be used to monitor semi-volatile organic compounds in the atmosphere. Polyurethane foam (PUF) disks are a popular sampling medium because they have a high retention capacity for such compounds. This paper reports a highly time-resolved uptake study, to derive uptake rate data under field conditions, and investigate the effects of using different foam densities on the uptake rate. PUF disks were deployed alongside an active sampler, for periods of up to 12 weeks. The uptake rates were measured for a range of gas- and particle-bound persistent organic pollutants (polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs)), of different properties, to explore whether gas–particle partitioning affected uptake rate. Uptake rates for two different densities of foam (0.021 and 0.035 g cm^?3) were not statistically significantly different from each other. Uptake rates of light PCBs averaged ～6.5 m³ day^?1, somewhat higher than in previous studies; higher wind speeds and lower temperatures in this study are the likely reason for this difference. The study showed: i) the uptake rate of the compound with lowest K_OA considered in this study (PCB-28/31) declined in the later weeks, indicating an approach to equilibrium; ii) uptake rates of lighter BDEs and heavier PCBs (compounds of intermediate K_OA in this study) remain similar throughout the study period, indicating that they are not approaching equilibrium during the 12-week-study; iii) uptake rates were typically: ～8 m³ day^?1 for PCB-52; ～9.5 m³ day^?1 for PCB-95; ～11 m³ day^?1 for BDE-28 and ～2 m³ day^?1 BDE-99. The latter compound has an important particle-bound component and this lowers the sampling rate compared to predicted uptake rates for compounds which are in the gas phase only. It is shown that knowledge of gas–particle partitioning is needed to correct for this effect, and to improve predicted uptake rates.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta—Seasonal variations at urban,suburban, and rural ambient air monitoring sites

Twenty-eight polycyclic aromatic hydrocarbons (PAH) and methylated PAHs (Me-PAH) were measured in daily PM_2.5 samples collected at an urban site, a suburban site, and a rural site in and near Atlanta during 2004 (5 samples/month/site). The suburban site, located near a major highway, had higher PM_2.5-bound PAH concentrations than did the urban site, and the rural site had the lowest PAH levels. Monthly variations are described for concentrations of total PAHs (∑PAHs) and individual PAHs. PAH concentrations were much higher in cold months than in warm months, with average monthly ∑PAH concentrations at the urban and suburban-highway monitoring sites ranging from 2.12 to 6.85 ng m^?3 during January–February and November–December 2004, compared to 0.38–0.98 ng m^?3 during May–September 2004. ∑PAH concentrations were found to be well correlated with PM_2.5 and organic carbon (OC) within seasons, and the fractions of PAHs in PM_2.5 and OC were higher in winter than in summer. Methyl phenanthrenes were present at higher levels than their un-substituted homologue (phenanthrene), suggesting a petrogenic (unburned petroleum products) input. Retene, a proposed tracer for biomass burning, peaked in March, the month with the highest acreage and frequency of prescribed burning and unplanned fires, and in December, during the high residential wood-burning season, indicating that retene might be a good marker for burning of all biomass materials. In contrast, potassium peaked only in December, indicating that it might be a more specific tracer for wood-burning.     

Evaluating inter-continental transport of fine aerosols:(2) Global health impact

In this second of two companion papers, we quantify for the first time the global impact on premature mortality of the inter-continental transport of fine aerosols (including sulfate, black carbon, organic carbon, and mineral dust) using the global modeling results of (Liu et al., 2009). Our objective is to estimate the number of premature mortalities in each of ten selected continental regions resulting from fine aerosols transported from foreign regions in approximately year 2000. Our simulated annual mean population-weighted (P-W) concentrations of total PM2.5 (aerosols with diameter less than 2.5 μm) are highest in East Asia (EA, 30 μg m^?3) and lowest in Australia (3.6 μg m^?3). Dust is the dominant component of PM2.5 transported between continents. We estimate global annual premature mortalities (for adults age 30 and up) due to inter-continental transport of PM2.5 to be nearly 380 thousand (K) in 2000. Approximately half of these deaths occur in the Indian subcontinent (IN), mostly due to aerosols transported from Africa and the Middle East (ME). Approximately 90K deaths globally are associated with exposure to foreign (i.e., originating outside a receptor region) non-dust PM2.5. More than half of the premature mortalities associated with foreign non-dust aerosols are due to aerosols originating from Europe (20K), ME (18K) and EA (15K); and nearly 60% of the 90K deaths occur in EA (21K), IN (19K) and Southeast Asia (16K). The lower and higher bounds of our estimated 95% confidence interval (considering uncertainties from the concentration–response relationship and simulated aerosol concentrations) are 18% and 240% of the estimated deaths, respectively, and could be larger if additional uncertainties were quantified. We find that in 2000 nearly 6.6K premature deaths in North America (NA) were associated with foreign PM2.5 exposure (5.5K from dust PM2.5). NA is least impacted by foreign PM2.5 compared to receptors on the Eurasian continent. However, the number of premature mortalities associated with foreign aerosols in NA (mostly occurring in the U.S.) is comparable to the reduction in premature mortalities expected to result from tightening the U.S. 8-h O₃ standard from 0.08 ppmv to 0.075 ppmv. International efforts to reduce inter-continental transport of fine aerosol pollution would substantially benefit public health on the Eurasian continent and would also benefit public health in the United States.     

The stable carbon isotope composition of PM2.5 and PM10 in Mexico City Metropolitan Area air

The sources and distribution of carbon in ambient suspended particles (PM_2.5 and PM₁₀) of Mexico City Metropolitan Area (MCMA) air were traced using stable carbon isotopes (¹³C/¹²C). Tested potential sources included rural and agricultural soils, gasoline and diesel, liquefied-petroleum gas, volcanic ash, and street dust. The complete combustion of LP gas, diesel and gasoline yielded the lightest δ¹³C values (?27 to ?29‰ vs. PDB), while street dust (PM₁₀) represented the isotopically heaviest endmember (?17‰). The δ¹³C values of rural soils from four geographically separated sites were similar (?20.7 ± 1.5‰). δ¹³C values of particles and soot from diesel and gasoline vehicle emissions and agricultural soils varied between ?23 and ?26‰. Ambient PM samples collected in November of 2000, and March and December of 2001 at three representative receptor sites of industrial, commercial and residential activities had a δ¹³C value centered around ?25.1‰ in both fractions, resulting from common carbon sources. The predominant carbon sources to MCMA atmospheric particles were hydrocarbon combustion (diesel and/or gasoline) and particles of geological origin. The significantly depleted δ¹³C values from the industrial site reflect the input of diesel combustion by mobile and point source emissions. Based on stable carbon isotope mass balance, the carbon contribution of geological sources at the commercial and residential sites was approximately 73% for the PM₁₀ fraction and 54% for PM_2.5. Although not measured in this study, biomass-burning emissions from nearby forests are an important carbon source characterized by isotopically lighter values (?29‰), and can become a significant contributor (67%) of particulate carbon to MCMA air under the prevalence of southwesterly winds. Alternative sources of these ¹³C-depleted particles, such as cooking fires and municipal waste incineration, need to be assessed. Results show that stable carbon isotope measurements are useful for distinguishing between some carbon sources in suspended particles to MCMA air, and that wind direction has an impact on the distribution of carbon sources in this basin.