沉积物颗粒表面分形特征的研究

通过一阶分子连接性指数^1X与分子表面积TSA之间的相关性计算出吸附分子的尺度，采用分形吸附等温线法计算出妫河沉积物的Ds为2．379，官厅沉积物的Ds为2．836．基于沉积物对N2的吸附．脱附等温线数据，采用FHH(Frenkel-Halsey-Hill)方程计算出两种沉积物的表面分形维数Ds，发现官厅沉积物与妫河沉积物的Ds相差不大；温度影响Ds主要是由于升温改变了沉积物的组成与结构．在本实验中采用热力学模型(thenmodynamic model)计算出的Ds值大都超过3．此外，沉积物的Ds与其比表面积、矿物含量、CEC、有机质的相关性差．以萘、菲、芘作为码尺计算出的Ds并不完全是表面空间填充能力的客观表现，而是表面吸附过程的一个重要的综合性特征参数．     

Seasonal variation and sources of derivatized phenols in atmospheric fine particulate matter in North China Plain

Qualitative and quantitative analyses of derivatized phenols in Beijing and in Xinglong were performed from 2016 to 2017 using gas chromatography-mass spectrometry.The results showed substantially more severe pollution in Beijing.Of the 14 compounds detected,the total average concentration was 100 ng/m~3 in Beijing,compared with 11.6 ng/m~3 in Xinglong.More specifically,concentration of nitro-aromatic compounds(NACs)(81.9 ng/m~3 in Beijing and 8.49 ng/m3 in Xinglong) was the highest,followed by aromatic acids(14.6 ng/m~3 in Beijing and 2.42 ng/m~3 in Xinglong) and aromatic aldehydes(3.62 ng/m~3 in Beijing and 0.681 ng/m~3 in Xinglong).In terms of seasonal variation,the highest concentrations were found for 4-nitrocatechol in winter in Beijing(79.1±63.9 ng/m~3) and 4-nitrophenol in winter in Xinglong(9.72±8.94 ng/m~3).The analysis also revealed diurnal variations across different seasons.Most compounds presented higher concentrations at night in winter because of the decreased boundary layer height and increased heating intensity.While some presented higher levels during the day,which attributed to the photo-oxidation process for summer and more biomass burning activities for autumn.Higher concentrations appeared in winter and autumn than in spring and summer,which resulted from more coal combustions and adverse meteorological conditions.The significant correlations among NACs indicated similar sources of pollution.Higher correlations presented within each subgroup than those between the subgroups.Good correlations between levoglucosan and nitrophenols,nitrocatechols,nitro salicylic acids,with correlation coefficients(r) of 0.66,0.69 and 0.69,respectively,indicating an important role of biomass burning among primary sources.     

Effect of sulfur source on photocatalytic degradation performance of CdS/MoS2 prepared with one-step hydrothermal synthesis

Cd S/Mo S_2,an extremely efficient photocatalyst,has been extensively used in hydrogen photoproduction and pollutant degradation.Cd S/Mo S_2can be synthesized by a facile one-step hydrothermal process.However,the effect of the sulfur source on the synthesis of Cd S/Mo S_2via one-step hydrothermal methods has seldom been investigated.We report herein a series of one-step hydrothermal preparations of Cd S/Mo S_2using three different sulfur sources:thioacetamide,L-cysteine,and thiourea.The results revealed that the sulfur source strongly affected the crystallization,morphology,elemental composition and ultraviolet(UV)–visible-light-absorption ability of the Cd S/Mo S_2.Among the investigated sulfur sources,thioacetamide provided the highest visible-light absorption ability for Cd S/Mo S_2,with the smallest average particle size and largest surface area,resulting in the highest efficiency in Methylene Blue(MB)degradation.The photocatalytic activity of Cd S/Mo S_2synthesized from the three sulfur sources can be arranged in the following order:thioacetamideL-cysteinethiourea.The reaction rate constants(k)for thioacetamide,L-cysteine,and thiourea were estimated to be 0.0197,0.0140,and 0.0084 min~(-1),respectively.However,thioacetamide may be limited in practical application in terms of its price and toxicity,while L-cysteine is relatively economical,less toxic and exhibited good photocatalytic degradation performance toward MB.     

Study on the effects of organic matter characteristics on the residual aluminum and flocs in coagulation processes

Characteristics of organic matter may affect the residual aluminum after the coagulation process. This study reported the results of a survey for one drinking water treatment plant and measured the concentration of residual aluminum species with different molecular weights.Survey results indicated that humic acid or organic matter whose molecular weight was smaller than 1500 Da had significant effects on residual aluminum. All the treatment processes were ineffective in removing dissolved organic matter whose molecular weight was smaller than1500 Da. These results also indicated that the addition of sand or polyacrylamide in the coagulation process could greatly decrease the concentration of humic acid, and the concentration of residual aluminum also decreased. These results revealed that for all water samples after filtration, the majority of total residual aluminum existed in the form of total dissolved aluminum, accounting for 70%–90%. The concentration of residual aluminum produced in bovine serum albumin solutions indicated that when the DOC was larger than4.0 mg/L, there were still significant differences when the solution p H value varied from 4.0 to 9.0.     

粉末活性炭的Fenton氧化再生

采用Fenton氧化法对吸附处理染料废水后的饱和粉末活性炭(饱和炭)进行再生,考察了饱和炭的再生效果及其主要影响因素。实验结果表明:饱和炭的最佳再生条件为H2O2投加量6.5 mmol/g、再生p H 3.0、H2O2与Fe2+的摩尔比10、再生时间1 h;最佳条件下的再生率(再生粉末活性炭(再生炭)与新粉末活性炭对废水COD去除率的百分比)约为60%;使用最佳再生条件下得到的再生炭对废水进行吸附处理,废水的COD去除率和脱色率分别约为27%和67%。     

重庆市北碚大气中PM2.5、NOx、SO2和O3浓度变化特征研究

重庆是我国西南工业重镇,但长期受大气污染困扰.利用全自动在线环境监测仪器,于2012年1月—2014年2月,对重庆市北碚区大气中的典型污染物PM2.5、NO_x、SO_2和O_3进行了观测研究.结果表明:重庆北碚大气首要污染物为PM2.5,2012和2013年平均浓度分别为(67.5±31.9)和(66.6±37.5)μg·m~(-3),是国家环境空气质量一级标准35μg·m~(-3)的1.9倍,两年超过国家二级标准的天数分别为119和126 d,年超标率均大于1/3;两年NO_x,SO_2及O_3的年平均浓度分别为(57.1±24.6)和(55.1±36.6),(43.1±24.0)和(35.0±21.9)及(31.1±24.9)和(48.5±37.4)μg·m~(-3).大气污染物浓度具有明显的季节变化特征,PM2.5和NO_x冬季污染最为严重,两年冬季平均值分别比两年年平均值高33.6%、59.6%和43.2%、8.5%;O_3表现为夏高冬低;SO_2春季最高且污染最轻.大气污染物日变化显示PM2.5和NO_x浓度呈双峰日变化形式,有早晚两个峰值,与城市交通高峰相对应.SO_2和O_3浓度呈单峰日变化,前者峰值出现在午前10∶00—12∶00大气对流层被打破之后,而后者峰值出现在午后16∶00局地光化学最强之时.消减各种污染源的颗粒物直接排放,消减气态污染物SO_2和NO_x的工业排放,消减机动车NO_x和VOCs等的排放,才有可能使重庆北碚的大气污染状况得到改善.     

含硅酸盐水解Fe(Ⅲ)溶液的形态分析方法——Fe-Ferron与β-Silicomolybdate法相结合

本文对含硅酸盐水解Fe（Ⅲ）溶液的形态分析方法进行了研究,对其中pH以及Fe（Ⅲ）浓度对反应的影响作了一定的探讨,实验结果表明,在pH为5.0,控制Fe（Ⅲ）浓度在8×10~(-5)mol·l~(-1)以下较为适宜。应用Ferron法与β-Silicomolybdate法相结合,可以分别获得含硅酸盐水解Fe（Ⅲ）溶液中Fe（Ⅲ）与Silica的赋存形态及其分布。因此,可以进一步应用于各种条件下含硅酸盐水解Fe（Ⅲ）溶液中的形态分布及其转化规律的研究。     

高铁酸钾调理改善活性污泥脱水性能的反应机制研究

研究了高铁酸钾(K_2FeO_4)对处理活性污泥脱水性的效果,重点考察了不同pH和剂量条件下,K_2FeO_4调理对污泥过滤脱水特性和胞外聚合物(EPS)分布和组成的影响,以深入认识K_2FeO_4调理污泥的反应机制.研究表明,K_2FeO_4调理效果随pH值的降低而改善,其不仅有氧化裂解作用导致结合型EPS(BEPS)释放,同时其还原产物三价铁离子兼具混凝功效,能够通过电中和与界面吸附去除部分溶解性EPS(SEPS),同时压缩EPS结构,增强污泥絮体结构.此外,当pH值为3,K_2FeO_4投加量为0.1 g·g~(-1)(以TSS计)时,污泥过滤脱水速率和程度均达到最佳.过量投加K_2FeO_4(0.2 g·g~(-1),以TSS计)后,BEPS大量释放,污泥过滤阻力增加,脱水性能恶化.     

Groundwater arsenic removal by coagulation using ferric(Ⅲ)sulfate and polyferric sulfate: A comparative and mechanistic study

Elevated arsenic(As) in groundwater poses a great threat to human health. Coagulation using mono- and poly-Fe salts is becoming one of the most cost-effective processes for groundwater As removal. However, a limitation comes from insufficient understanding of the As removal mechanism from groundwater matrices in the coagulation process, which is critical for groundwater treatment and residual solid disposal. Here, we overcame this hurdle by utilizing microscopic techniques to explore molecular As surface complexes on the freshly formed Fe flocs and compared ferric(III) sulfate(FS) and polyferric sulfate(PFS)performance, and finally provided a practical solution in As-geogenic areas. FS and PFS exhibited a similar As removal efficiency in coagulation and coagulation/filtration in a two-bucket system using 5 mg/L Ca(ClO)_2. By using the two-bucket system combining coagulation and sand filtration, 500 L of As-safe water( 10 μg/L) was achieved during five treatment cycles by washing the sand layer after each cycle. Fe k-edge X-ray absorption near-edge structure(XANES) and As k-edge extended X-ray absorption fine structure(EXAFS) analysis of the solid residue indicated that As formed a bidentate binuclear complex on ferrihydrite, with no observation of scorodite or poorly-crystalline ferric arsenate. Such a stable surface complex is beneficial for As immobilization in the solid residue, as confirmed by the achievement of much lower leachate As(0.9 μg/L–0.487 mg/L)than the US EPA regulatory limit(5 mg/L). Finally, PFS is superior to FS because of its lower dose, much lower solid residue, and lower cost for As-safe drinking water.     

Groundwater arsenic removal by coagulation using ferric(III) sulfate and polyferric sulfate: A comparative and mechanistic study

Elevated arsenic (As) in groundwater poses a great threat to human health. Coagulation using mono-and poly-Fe salts is becoming one of the most cost-effective processes for groundwater As removal. However, a limitation comes from insufficient understanding of the As removal mechanism from groundwater matrices in the coagulation process, which is critical for groundwater treatment and residual solid disposal. Here, we overcame this hurdle by utilizing microscopic techniques to explore molecular As surface complexes on the freshly formed Fe flocs and compared ferric(III) sulfate (FS) and polyferric sulfate (PFS) performance, and finally provided a practical solution in As-geogenic areas. FS and PFS exhibited a similar As removal efficiency in coagulation and coagulation/filtration in a two-bucket system using 5 mg/L Ca(ClO)₂. By using the two-bucket system combining coagulation and sand filtration, 500 L of As-safe water (<10 μg/L) was achieved during five treatment cycles by washing the sand layer after each cycle. Fe k-edge X-ray absorption near-edge structure (XANES) and As k-edge extended X-ray absorption fine structure (EXAFS) analysis of the solid residue indicated that As formed a bidentate binuclear complex on ferrihydrite, with no observation of scorodite or poorly-crystalline ferric arsenate. Such a stable surface complex is beneficial for As immobilization in the solid residue, as confirmed by the achievement of much lower leachate As (0.9 μg/L-0.487 mg/L) than the US EPA regulatory limit (5 mg/L). Finally, PFS is superior to FS because of its lower dose, much lower solid residue, and lower cost for As-safe drinking water.