Mitigation of hydrogen fluoride aerosols by dry powders

Fluid bed tests were used to determine overall reaction rates for eight different dry powders of low hazard and toxicity before and after reaction with HF. In flow chamber tests, a representative oxide, hydroxide and carbonate were used to measure the efficiency of mitigation of an HF aerosol cloud. The results show that dry powders provide a valid alternative to water spray mitigation. Powder efficiencies are higher than water efficiencies at constant weight ratio.

At present, no attempt has been made to provide any technical designs or layouts for powder mitigation systems. However, the technology for smaller systems is available through manufacturers of dry powder chemical fire extinguisher equipment. When these powders are kept dry and under nitrogen atmosphere, a shelf life of several years can be expected.     

TOPHAZOP: a knowledge-based software tool for conducting HAZOP in a rapid, efficient yet inexpensive manner

Hazard and operability (HAZOP) studies constitute an essential step in the risk analysis of any chemical process industry and involve systematic identification of every conceivable abnormal process deviation, its causes and abnormal consequences. These authors have recently proposed optHAZOP as an alternative procedure for conducting HAZOP studies in a shorter span of time than taken by conventional HAZOP procedure, with greater accuracy and effectiveness [Khan, F. I. and Abassi, S. A., optHAZOP. An effective and efficient technique for hazard identification and assessment Journal of Loss Prevention in the Process Industries, 1997, 10, 191–204]. optHAZOP consists of several steps, the most crucial one requires use of a knowledge-based software tool which would significantly reduce the requirement of expert man-hours and speed up the work of the study team. TOPHAZOP (Tool for OPTmizing HAZOP) has been developed to fulfil this need.

The TOPHAZOP knowledge-base consists of two main branches: process-specific and general. The TOPHAZOP framework allows these two branches to interact during the analysis to address the process-specific aspects of HAZOP analysis while maintaining the generality of the system. The system is open-ended and modular in structure to make easy implementation and/or expansion of knowledge. The important features of TOPHAZOP and its performance on an industrial case study are described.     

The Properties of Poly(<Emphasis Type="SmallCaps">l</Emphasis>-Lactide) Prepared by Different Synthesis Procedure

Different synthesis methods were applied to determine optimal conditions for polymerization of (3S)-cis-3,6-dimethyl-1,4-dioxane-2,5-dione (l-lactide), in order to obtain poly(l-lactide) (PLLA). Bulk polymerizations (in vacuum sealed vessel, high pressure reactor and in microwave field) were performed with tin(II) 2-ethylhexanoate as the initiator. Synthesis in the vacuum sealed vessel was carried out at the temperature of 150 °C. To reduce the reaction time second polymerization process was carried out in the high pressure reactor at 100 °C and at the pressure of 138 kPa. The third type of rapid synthesis was done in the microwave reactor at 100 °C, using frequency of 2.45 GHz and power of 150 W at the temperature of 100 °C. The temperature in this method was controlled via infrared system for in-bulk measuring. The solution polymerization (with trifluoromethanesulfonic acid as initiator) was possible even at the temperature of 40 °C, yielding PLLA with narrow molecular weight distribution in a very short period of time (less than 6 h). The obtained polymers had the number-average molecular weights ranging from 43,000 to 178,000 g mol⁻¹ (polydispersity index ranging from 1 to 3) according to the gel permeation chromatography measurements. The polymer structure was characterized by Fourier transform infrared and NMR spectroscopy. Thermal properties of the obtained polymers were investigated using thermogravimetry and differential scanning calorimetry.     

Application of a Second-Order Kinetic Model to a Complex Melt Polymerization Reaction

A novel copolymer system has been synthesized using methyl hydroquinone diacetate (MHQDA), 1,4 naphthalene dicarboxylic acid (1,4 NDCA), and polybutylene terephthalate (PBT) using the melt polymerization technique. The optimum kinetic parameters pertinent to this system are reported in this study. A simple second-order reaction sequence summarizes catalyzed and uncatalyzed reactions between MHQDA, 1,4 NDCA, and PBT. The kinetic parameters for the copolymerization reaction were determined using a new second-order model. This technique was used to compute the moles of acetic acid generated in the polymerization process. The model was compared to that of the experimentally determined data. Close comparison (percentage error of less than 5%) was obtained between the experimental and theoretical data. The kinetic data support block copolyester formation. The thermal data also supports formation of block polymers.     

Performance of a low cost MBT prior to landfilling: study of the biological treatment of size reduced MSW without mechanical sorting

In France, the interest in Mechanical Biological Treatment (MBT) prior to landfilling is actually growing. In the absence of acceptance criteria for the waste to be landfilled, an alternative to the intensive, high-technology MBT can only find its place in the French context if it shows substantial benefits from an environmental, economic or operational point of view. This paper presents an experiment of low-cost MBT of size reduced MSW without material splitting. The performance of an experimental, pilot-scale mechanical and biological treatment process has been studied on 37.5 Mg of raw municipal solid waste. The mechanical process has been kept simple with only coarse shredding and no material recovery. The biological treatment, which was a low-cost forced aeration process, was monitored for 25 weeks. The biogas production potential of the waste was reduced by 90% to 19 NL kgDM(-1). The initial AT4 index of 82.9 mg O2 gDM(-1) decreased to 16.0 mg O2 gDM(-1). After 25 weeks of aerobic treatment, the dry mass loss reached 37%, while the mass of waste going to landfill was reduced by 28%. The average performances of the process were explained by the biological process itself, which was not optimal, and also by the characteristics of the input waste. The high particle size of the treated waste and the high content of slowly biodegradable matter (such as paper and cardboard) may both be significant drawbacks for the biological stabilisation of waste.     

The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.     

Determinants of Farmers’ Adoption of Improved Soil Conservation Technology in a Middle Mountain Watershed of Central Nepal

This study explores different socio-economic and institutional factors influencing the adoption of improved soil conservation technology (ISCT) on Bari land (Rainfed outward sloping terraces) in the Middle Mountain region of Central Nepal. Structured questionnaire survey and focus group discussion methods were applied to collect the necessary information from farm households. The logistic regression model predicted seven factors influencing the adoption of improved soil conservation technology in the study area including years of schooling of the household head, caste of the respondent, land holding size of the Bari land, cash crop vegetable farming, family member occupation in off farm sector, membership of the Conservation and Development Groups, and use of credit. The study showed that technology dissemination through multi-sectoral type community based local groups is a good option to enhance the adoption of improved soil conservation technology in the Middle Mountain farming systems in Nepal. Planners and policy makers should formulate appropriate policies and programs considering the farmers' interest, capacity, and limitation in promoting improved soil conservation technology for greater acceptance and adoption by the farmers.     

Development and Adoption of a Simple Nonpoint Source Pollution Model for Port Phillip Bay,Australia

New computing tools and approaches allow tailored development of software to meet the needs of environmental managers. The processes required for such tailoring fit well with adaptive management concepts where, as knowledge and system understanding develop among managers, the software can be developed or replaced to match. This paper reports on development and adoption of a simple nonpoint source pollution modeling tool, including technical aspects of data support for modeling and social aspects of software design. The software, named FILTER, used a unit load model to generate expected pollutant loads from subcatchments of Port Phillip Bay, Australia. Monitoring data were used for calibration to modify the delivery of generated pollutants to receiving waters. Spatial, tabular, and charting software components were used to provide alternative forms of output visualization. FILTER was developed using a process that resulted in manager-stakeholders taking responsibility for setting of model parameter values and operation of the user interface, thereby encouraging uptake. The inclusive development process, tailoring of the software to manager needs and styles of usage, and matching of model complexity to data and knowledge, resulted in a successful application that has become the current agreed system representation among disparate stakeholder organizations.