How to improve reliability in groundwater analysis: over a decade of experience with external quality control in field campaigns on volatile halogenated compounds

The reliability in measurement results obtained during environmental monitoring is crucial for the assessment and further planning of remediation efforts on the respective contaminated sites by the responsible authorities. A case study concerned with groundwater contaminated with perchloroethylene, trichloroethylene and 1,1,2-trichlorotrifluoroethane including their degradation products which involves private contract laboratories and an independent provider of quality assurance (QA) is presented. The experience gained with biannual monitoring campaigns over 14 years indicates that the selection of contractors on basis of accreditation status and successful performance in interlaboratory comparisons are not sufficient. Rather the auditing of the contractors by the QA provider prior to each campaign and the crosschecking of selected monitoring samples by the QA provider led to a lasting improvement of reliability in the contractors' measurement results. A mean deviation of 20% from the reference value determined by the QA provider for the crosschecked samples was reached.     

Evaluation of the field dissipation of fungicides and insecticides used on fruit bearing trees in northern Italy

The dissipation of the fungicides captan, cyprodinil, fludioxonil, dithianon, and tebuconazole and of the insecticides chlorpyrifos, fenitrothion, and malathion was studied, following a single treatment of different cultivars of pears, apples, and peaches. The study was conducted in northern Italy, over two successive growing seasons (2004 and 2005). The treatments were performed by the farmers involved, in line with their usual practice. At various time intervals from treatment to harvest, representative samples of fruit were collected and analyzed for pesticide residues. In some cases, concentrations lower than the maximum residue levels (MRLs) were found immediately after treatment. In all trials a rapid decline in pesticide concentrations was observed leading to residues at harvest greatly below the MRLs.     

Zero-valent iron and iron oxide-coated sand as a combination for removal of co-present chromate and arsenate from groundwater with humic acid

The combination of zero-valent iron (Fe⁰) and iron oxide-coated sand (IOCS) was used to remove Cr(VI) and As(V) from groundwater in this study. The efficiency and the removal mechanism of Cr(VI) and As(V) by using this combination, with the influence of humic acid (HA), were investigated using batch experiments. Results showed that, compared to using Fe⁰ or IOCS alone, the Fe⁰-IOCS can perform better on the removal of both Cr(VI) and As(V). Metal extraction studies showed that As(V) was mainly removed by IOCS and iron corrosion products while Cr(VI) was mainly removed by Fe⁰ and its corrosion products. Competition was found between Cr(VI) and As(V) for the adsorption sites on the iron corrosion products. HA had shown insignificant effects on Cr(VI) removal but some effects on As(V) removal kinetics. As(V) was adsorbed on IOCS at the earlier stage, but adsorbed/coprecipitated with the iron corrosion products at the later stage.     

Alternative antimicrobial compounds to control potential Lactobacillus contamination in bioethanol fermentations

Antibiotics are commonly used to control microbial contaminants in yeast-based bioethanol fermentation. Given the increase in antibiotic-resistant bacteria, alternative natural antimicrobials were evaluated against the potential contaminant, Lactobacillus. The effects of nisin, ?-polylysine, chitosan (CS) and lysozyme were screened against 5 Lactobacillus strains. A standard broth- microdilution method was used in 96-well plates to assess the minimal inhibitory concentration (MIC). L. delbrueckii subsp lactis ATCC479 exhibited maximal MICs with CS, ?-polylysine and nisin (1.87, 0.3125 and 0.05 mg/mL, respectively). Nisin reduced most Lactobacillus strains by 6 log CFU/mL after 48 hours with the exception of L. casei. Synergism occurred when ethylenediaminetetraacetic acid (EDTA) was added with nisin. An MIC of 0.4 mg/mL of nisin combined with the EDTA at an MIC of 1 mg/ml markedly suppressed L .casei by 6 log CFU/mL. In conclusion, alternative antimicrobials proved to be a potential candidate for controlling bacterial contamination in the fermentation process. Synergistic effect of nisin with EDTA successfully inhibited the nisin-resistant contaminant, L. casei.     

Significance of metal exchange in EDDS-flushing column experiments

Chelating agents have been widely studied for extracting heavy metals from contaminated soils, and the effectiveness of EDDS ([S,S]-ethylene-diamine-disuccinic acid) has aroused extensive attention because of its biodegradability in the natural environment. However, in the course of EDDS-flushing, metal exchange of newly extracted metal-EDDS complexes with other sorbed metals and mineral cations may result in metal re-adsorption on the soil surfaces. Therefore, this study investigated the relative significance of metal exchange under different travel distances of chelant complexes, characteristics of soil contamination, and solution pH in the column experiments. As a result of metal exchange, the elution of Zn and Pb was retarded and the cumulative extraction was lower than those of Ni and Cu, especially over a longer travel distance. Compared with the field-contaminated soils, the effects of metal exchange were even more substantial in the artificially contaminated soil because of a greater amount of extractable metals and a larger proportion of weakly bound fractions. By contrast, metal exchange was insignificant at pH 8, probably due to less adsorption of metal-EDDS complexes. These findings highlight the conditions under which metal exchange of metal-EDDS complexes and the resulting impacts are more significant during EDDS-flushing.     

Influences of redox transformation, metal complexation and aggregation of fulvic acid and humic acid on Cr(VI) and As(V) removal by zero-valent iron

This study investigated the removal kinetics and mechanisms of Cr(VI) and As(V) by Fe(0) in the presence of fulvic acid (FA) and humic acid (HA) by means of batch experiments. The focus was on the involvements of FA and HA in redox reactions, metal complexation, and iron corrosion product aggregation in the removal of Cr(VI) and As(V) removal by Fe(0). Synthetic groundwater was used as the background electrolyte to simulate typical groundwater. The results showed faster Cr(VI) removal in the presence of HA compared to FA. Fluorescence spectroscopy revealed that no redox reaction occurred in the FA and HA. The results of the speciation modeling indicate that the free Fe(II) concentration was higher in the presence of HA, resulting in a higher removal rate of Cr(VI). However, the removal of As(V) was inhibited in the HA solution. Speciation modeling showed that the concentration of dissolved metal-natural organic matter (metal-NOM) complexes significantly affected the aggregation of the iron corrosion products which in turn affected the removal of As(V). The aggregation was found to be induced by gel-bridging of metal-NOM with the iron corrosion products. The effects of metal-NOM on the aggregation of the iron corrosion products were further confirmed by TEM studies. Larger sizes of iron corrosion products were formed in the FA solution compared to HA solution. This study can shed light on understanding the relationships between the properties of NOM (especially the content of metal-binding sites) and the removal of Cr(VI) and As(V) by Fe(0).     

Integration of post-combustion capture and storage into a pulverized coal-fired power plant

Post-combustion CO₂ capture and storage (CCS) presents a promising strategy to capture, compress, transport and store CO₂ from a high volume–low pressure flue gas stream emitted from a fossil fuel-fired power plant. This work undertakes the simulation of CO₂ capture and compression integration into an 800 MW_e supercritical coal-fired power plant using chemical process simulators. The focus is not only on the simulation of full load of flue gas stream into the CO₂ capture and compression, but also, on the impact of a partial load. The result reveals that the energy penalty of a low capture efficiency, for example, at 50% capture efficiency with 10% flue gas load is higher than for 90% flue gas load at the equivalent capture efficiency by about 440 kWh_e/tonne CO₂. The study also addresses the effect of CO₂ capture performance by different coal ranks. It is found that lignite pulverized coal (PC)-fired power plant has a higher energy requirement than subbituminous and bituminous PC-fired power plants by 40.1 and 98.6 MW_e, respectively. In addition to the investigation of energy requirement, other significant parameters including energy penalty, plant efficiency, amine flow rate and extracted steam flow rate, are also presented. The study reveals that operating at partial load, for example at half load with 90% CO₂ capture efficiency, as compared with full load, reduces the energy penalty, plant efficiency drop, amine flow rate and extracted steam flow rate by 9.9%, 24.4%, 50.0% and 49.9%, respectively. In addition, the effect of steam extracted from different locations from a series of steam turbine with the objective to achieve the lowest possible energy penalty is evaluated. The simulation shows that a low extracted steam pressure from a series of steam turbines, for example at 300 kPa, minimizes the energy penalty by up to 25.3%.     

Zinc distribution in soils amended with different kinds of sewage sludge

Sewage sludge (SS) can be applied to cropland to supply and recycle nutrients and organic carbon. Potentially toxic elements in the sludge, however, are of environmental concern. This study evaluates the changes in chemical speciation of Zn in three representative pristine soils of the Pampas Region, Argentina, measured with sequential extraction over a one-year period. Pure SS or SS containing 30% (DM) of its own incineration ash (AS) was applied to the soils at an application rate of 150Mgha(-1). Zn was sequentially fractionated into exchangeable, organically bound, inorganic and residual fractions. The application of the SS and AS amendments significantly increased Zn concentration in all soil fractions at each sampling date. At day 1, Zn was mainly found in the residual fraction. A year after the application of the amendments, redistribution towards the inorganic fraction was observed (41-76% of total Zn content). Zn found in exchangeable and inorganic fractions depended on soil pH rather than on the type of soil used. A negative and significant correlation was found between exchangeable Zn concentrations and soil pH (r=0.94), and a positive and significant correlation between inorganic Zn concentrations and soil pH (r=0.92). For each amended soil and sampling date, no significant differences were observed between SS or AS treatments for the exchangeable fraction. Moreover, the use of AS did not cause significant differences in Zn concentration in the other soil fractions compared to SS. Based on these results, land spreading of AS may be similar to SS diaposal in terms of Zn mobility.     

On the thermally induced isomerisation of hexabromocyclododecane stereoisomers

The interconversion of the stereoisomers contained in technical 1,2,5,6,9,10-hexabromocyclododecane, a major brominated flame retardant increasingly found in the environment and in biota, was investigated at elevated temperatures. The application of pure enantiomers of the three constituents alpha-, beta-, and gamma-HBCD enabled the unambiguous elucidation of the individual isomerisation reactions as well as the quantification of all respective rate constants. At 160 degrees C the rate constants range over two orders of magnitude from 1.50x10(-3) to 1.88x10(-5)mol(%)s(-1). A preliminary mechanistic explanation for the differences of the rate constants which govern the composition of HBCD diastereomers at equilibrium is given.     

Copper extraction effectiveness and soil dissolution issues of EDTA-flushing of artificially contaminated soils

Ethylenediaminetetraacetic acid (EDTA) was used as a reference chelating agent in column experiments to investigate the effectiveness of chelant-enhanced flushing of soils artificially contaminated under various conditions (low/high Cu loading, and aging). The associated soil dissolution issues were of particular concern. Dissolution of indigenous Fe/Al oxides, Ca carbonates and organic matter was monitored over the course of flushing. Regardless of contamination condition, above 85% extraction efficiency could be accomplished by 10(-2) and 10(-3)M EDTA-flushing, but not 10(-4)M. The Cu extraction kinetics positively correlated to EDTA concentration but inversely to Cu loading in soils. In addition to extraction from weakly sorbed fractions, a large portion of Cu was extracted from oxide, organic matter and residual fractions, which appears to derive from soil dissolution. Cumulative dissolved amounts of Fe, Al, and Ca were found to reach as high as hundreds of mgkg(-1), which were comparable to Cu contamination. Soil organic matter, which is known to strongly interact with Fe and Al oxides, was also mobilized. The rate and extent of these soil dissolutions were also positively correlated to EDTA concentration. Therefore, the co-extraction of soil minerals and organic matter during chelant-enhanced flushing, which would alter both physical structure and chemical properties of the soils, is detrimental to future land use and deserves greater attention. The concentration of chelating agent is the most crucial factor for an effective soil flushing with minimal damage.